The effects of Y and Zn/Y on hot tearing susceptibility (HTS) of Mg–6.5Zn–xY–0.5Zr (x = 4, 9, 12 and 18) and Mg–5Zn–13.5Y–0.5Zr alloys were investigated herein. The results illustrated that HTS of the investigated alloys decreased in the following order: Mg–6.5Zn–4Y–0.5Zr > Mg–6.5Zn–18Y–0.5Zr > Mg–6.5Zn–9Y–0.5Zr > Mg–6.5Zn–12Y–0.5Zr > Mg–5Zn–13.5Y–0.5Zr. The results also showed that HTS of the α-Mg-based alloy containing only LPSO phase was lower than that of the alloy containing only W-phase and (I+W) or (W+LPSO) mixed secondary phases. This was attributed to the coherence relationship between LPSO phase and α-Mg, and the bridging effect of LPSO phase.
WangYS, SunBD, WangQD, An understanding of the hot tearing mechanism in AZ91 magnesium alloy. Mater Lett. 2002;53:35–39. doi: 10.1016/S0167-577X(01)00449-9
2.
SongJF, WangZ, HuangYD, Effect of Zn addition on hot tearing behaviour of Mg–0.5Ca–xZn alloys. Mater Des. 2015;87:157–170. doi: 10.1016/j.matdes.2015.08.026
3.
ChenYH, WangLP, FengYC, Effect of Al content on hot tearing behaviour of Mg–xAl–2ca–2Sm alloys. Mater Sci Technol. 2019;35:116–126. doi: 10.1080/02670836.2018.1545282
4.
WangJF, SongPF, GaoS, Influence of Y on the phase composition and mechanical properties of as-extruded Mg–Zn–Y–Zr magnesium alloys. J Mater Sci. 2012;47:2005–2010. doi: 10.1007/s10853-011-5998-2
5.
SrinivasanA, WangZ, HuangYD, Hot tearing characteristics of binary Mg–Gd alloy castings. Metall Mater Trans A. 2013;44:2285–2298. doi: 10.1007/s11661-012-1593-7
6.
GundeP, SchifflA, UggowitzerPJ.Influence of yttrium additions on the hot tearing susceptibility of magnesium–zinc alloys. Mater Sci Eng A. 2010;527:7074–7079. doi: 10.1016/j.msea.2010.07.086
7.
NasresfahaniMR, NiroumandB.A new criterion for prediction of hot tearing susceptibility of cast alloys. Metall Mater Trans A. 2014;45:3699–3702. doi: 10.1007/s11661-014-2341-y
8.
HatamiN, BabaeiR, DadashzadehM, Modeling of hot tearing formation during solidification. J Mater Process Technol. 2008;205:506–513. doi: 10.1016/j.jmatprotec.2007.11.260
9.
KouS.A criterion for cracking during solidification. Acta Mater. 2015;88:366–374. doi: 10.1016/j.actamat.2015.01.034
10.
UludağM, ÇetinR, DispinarD.Freezing range, melt quality, and hot tearing in Al–Si alloys. Metall Mater Trans A. 2018;49:1948–1961. doi: 10.1007/s11661-018-4512-8
11.
EskinDG, SuyitnoS, KatgermanL.Mechanical properties in the semi-solid state and hot tearing of aluminium alloys. Prog Mater Sci. 2004;49:629–711. doi: 10.1016/S0079-6425(03)00037-9
12.
SubrotoT, MirouxA, BouffierL, Formation of hot tear under controlled solidification conditions. Metall Mater Trans A. 2014;45:2855–2862. doi: 10.1007/s11661-014-2220-6
13.
HaoH, MaijerDM, WellsMA, Modeling the stress-strain behavior and hot tearing during direct chill casting of an AZ31 magnesium billet. Metall Metal Trans A. 2010;41:2067–2077. doi: 10.1007/s11661-010-0216-4
14.
SongJF, WangZ, HuangYD, Hot tearing susceptibility of Mg–Ca binary alloys. Metall Mater Trans A. 2015;46:6003–6017. doi: 10.1007/s11661-015-3165-0
15.
LiuJW, KouS.Susceptibility of ternary aluminum alloys to cracking during solidification. Acta Mater. 2017;125:513–523. doi: 10.1016/j.actamat.2016.12.028
16.
LiuJW, KouS.Crack susceptibility of binary aluminum alloys during solidification. Acta Mater. 2016;110:84–94. doi: 10.1016/j.actamat.2016.03.030
17.
LiuJW, KouS.Effect of diffusion on susceptibility to cracking during solidification. Acta Mater. 2015;100:359–368. doi: 10.1016/j.actamat.2015.08.064
18.
WeiZQ, WangY, LiuZ.Effects of Zn and Y on hot-tearing susceptibility of Mg–xZn–2xY alloys. Mater Sci Technol. 2018;34:2001–2007. doi: 10.1080/02670836.2018.1507696
19.
WeiZQ, LiuZ, WangZ, Effects of Y on hot tearing susceptibility of Mg–Zn–Y–Zr alloys. Chin J Nonferrous Met. 2018;28:233–240.
20.
TakaiR, EndoN, HiroharaR, Experimental and numerical analysis of grain refinement effect on hot tearing susceptibility for Al–Mg alloys. Int J Adv Manuf Technol. 2019;100:1867–1880. doi: 10.1007/s00170-018-2791-2
21.
WangWK, MaLM, ChaiSC, Role of one direction strong texture in stretch formability for ZK60 magnesium alloy sheet. Mater Sci Eng A. 2018;730:162–167. doi: 10.1016/j.msea.2018.05.113
22.
LiHY, BaiYY, ZhangHT, Effect of Mn on hot cracking tendency of Mg–6.5Zn alloys. Acta Metall Sin. 2014;50:1237–1243.
23.
ZhouL, HuangYD, MaoPL, Influence of composition on hot tearing in binary Mg–Zn alloys. Int J Cast Metals Res. 2011;24:170–176. doi: 10.1179/136404611X13001912813942
24.
XuDK, LiuL, XuYB, The effect of precipitates on the mechanical properties of ZK60–Y alloy. Mater Sci Eng A. 2006;420:322–332. doi: 10.1016/j.msea.2006.01.092
25.
ZhouHT, ZhangZD, LiuCM, Effect of Nd and Y on the microstructure and mechanical properties of ZK60 alloy. Mater Sci Eng A. 2007;445–446:1–6. doi: 10.1016/j.msea.2006.04.028
26.
ZhaoZD, ChenQ, ChaoHY, Microstructural evolution and tensile mechanical properties of thixoforged ZK60–Y magnesium alloys produced by two different routes. Mater Des. 2010;31:1906–1916. doi: 10.1016/j.matdes.2009.10.056
27.
SongJF, WangZ, HuangYD, Hot tearing characteristics of Mg–2Ca–xZn alloys. J Mater Sci. 2016;51:2687–2704. doi: 10.1007/s10853-015-9583-y
28.
UpadhyaKG, StefanescuDM, LieuK, Computer-aided cooling curve analysis: principles and applications in metal casting. AFS Trans. 1989;97:61–66.
29.
HuangZH, LiangSM, ChenRS, Solidification pathways and constituent phases of Mg–Zn–Y–Zr alloys. J Alloys Compd. 2009;468:170–178. doi: 10.1016/j.jallcom.2008.01.034
30.
ClyneB, DaviesGJ.The influence of composition on solidification cracking susceptibility in binary alloys. Brit Found. 1981;74:65–73.
31.
MuthurajaC, BalasundarI, RaviKR.Determination of liquid fraction in Mg–Zn–Y alloys: thermal analysis versus thermodynamic approach. Trans Indian Inst Met. 2018;71:2807–2811. doi: 10.1007/s12666-018-1419-4
32.
LiuZ, ZhangSB, MaoPL, Effects of Y on hot tearing formation mechanism of Mg–Zn–Y–Zr alloys. Mater Sci Technol. 2014;30:1214–1222. doi: 10.1179/1743284713Y.0000000437
33.
GaoG, KouS.Hot cracking of binary Mg–Al alloy castings. Mater Sci Eng A. 2006;417:230–238. doi: 10.1016/j.msea.2005.10.050
34.
GaoG, KouS.Hot tearing of ternary Mg−Al−Ca alloy castings. Metall Mater Trans A. 2006;37:3647–3663. doi: 10.1007/BF02586212
35.
LeeJY, KimDH, LimHK, Effects of Zn/Y ratio on microstructure and mechanical properties of Mg–Zn–Y alloys. Mater Lett. 2005;59:3801–3805. doi: 10.1016/j.matlet.2005.06.052
36.
WangZ, LiYZ, WangF, Hot tearing susceptibility of Mg–xZn–2Y alloys. Trans Nonferrous Met Soc China. 2016;26:3115–3122. doi: 10.1016/S1003-6326(16)64443-6
37.
DavisTA, BichlerL, D'EliaF, Effect of TiBor on the grain refinement and hot tearing susceptibility of AZ91D magnesium alloy. J Alloys Compd. 2018;759:70–79. doi: 10.1016/j.jallcom.2018.05.129
ArnbergL, ChaiG, BackerudL.Determination of dendritic coherency in solidifying melts by rheological measurements. Mater Sci Eng A. 1993;173:101–103. doi: 10.1016/0921-5093(93)90195-K
40.
WangYB, HuangYX, MengXC, Microstructural evolution and mechanical properties of Mg–Zn–Y–Zr alloy during friction stir processing. J Alloys Compd. 2017;696:875–883. doi: 10.1016/j.jallcom.2016.12.068
41.
LiZM, WanDQ, HuangY, Characterization of a Mg95.5Zn1.5Y3 alloy both containing W phase and LPSO phase with or without heat treatment. J Magnesium Alloys. 2017;5:217–224. doi: 10.1016/j.jma.2017.05.003
42.
ZhouZJ, LiuZ, WangY, Effects of the second phase on hot tearing susceptibility of Mg-Zn-Y alloy. Mater Res Express. 2019;6:016529. doi: 10.1088/2053-1591/aae542
