The aim of this work was to study effects of hot extrusion on the microstructure of Ti-6Al-4V (wt-%) alloy processed by ECAP. Firstly, an isothermally Ti–6Al–4V alloy processed by Equal channel angular pressing(ECAP) was preheated at 950°C for 6 min and then hot extruded at 900°C. The hot extrusion minimised the grain size and maximised the mechanical strength. Therefore, it was demonstrated that hot extrusion of Ti-6Al-4V alloys that processed by ECAP could be performed without compromising any mechanical properties. Therefore, it is possible to use the ability to apply a reduced cross-section in hot extrusion for an Ti-6Al-4V processed by ECAP without concern about the reduction of properties.
SemenovaI.P., RaabG.I., GolubovskiyE.R., ValievR.R., Service properties of ultrafine-grained Ti–6Al–4V alloy at elevated temperature, J Mater Sci. 48 (2013) 4806–4812. doi:10.1007/s10853-013-7305-x.
2.
SalishchevG.A., GaleyevR.M., ValiakhmetovO.R., SaR. V, LutfullinR.Y., Development of Ti ± 6Al ± 4V sheet with low temperature superplastic properties, J Mater Process Technol. 116 (2001) 6–9. doi: 10.1016/S0924-0136(01)01037-8
3.
MatsumotoH., YoshidaK., LeeS., OnoY., ChibaA., Ti – 6Al – 4V alloy with an ultrafine-grained microstructure exhibiting low-temperature–high-strain-rate superplasticity, Mater Lett. 98 (2013) 209–212. doi:10.1016/j.matlet.2013.02.033.
4.
LeeT., ShihD.S., LeeY., LeeC.S., Manufacturing ultrafine-grained Ti-6Al-4V Bulk Rod using Multi-pass Caliber-Rolling, Metals (Basel). (2015) 777–789. doi:10.3390/met5020777.
5.
SemenovaI.P., PolyakovA. V, PolyakovaV. V, HuangY., ValievR.Z., LangdonT.G., High-cycle fatigue behavior of an ultra fine-grained Ti – 6Al – 4V alloy processed by ECAP and extrusion, Adv Eng Mater. (2016) 1–6. doi:10.1002/adem.201500630.
PolyakovA. V, SemenovaI.P., HuangY., ValievR.Z., LangdonT.G., Fatigue Life and Failure Characteristics of an ultrafine-grained Ti – 6Al – 4V alloy processed by ECAP and extrusion, Adv Eng Mater. (2014) 1–6. doi:10.1002/adem.201300530.
8.
LangdonT.G., Twenty-five years of ultrafine-grained materials: Achieving exceptional properties through grain refinement, Acta Mater. 61 (2013) 7035–7059. doi:10.1016/j.actamat.2013.08.018.
9.
SemenovaI.P., RaabG.I., SaitovaL.R., ValievR.Z., The effect of equal-channel angular pressing on the structure and mechanical behavior of Ti–6Al–4V alloy, Mater Sci Eng. 389 (2004) 805–808. doi:10.1016/j.msea.2004.02.093.
10.
SemiatinS.L., DeloD.P., Equal channel angular extrusion of difficult-to-work alloys, Mater Des. 21 (2000) 311–322. doi: 10.1016/S0261-3069(99)00085-0
11.
DeloD.P., SemiatinS.L., Hot working of Ti-6Al-4V via equal channel angular extrusion, Metall Mater Trans A. 30 (1999) 2473–2481. doi: 10.1007/s11661-999-0256-9
12.
KoY.G., JungW.S., ShinD.H., LeeC.S., Effects of temperature and initial microstructure on the equal channel angular pressing of Ti – 6Al – 4V alloy, Scr Mater. 48 (2003) 197–202. doi: 10.1016/S1359-6462(02)00356-1
13.
SemenovaI.P., SaitovaL.R., RaabG.I., KorshunovA.I., Microstructural features and mechanical properties of the Ti-6Al- 4V ELI alloy processed by severe plastic deformation, Mater Sci Forum. 504 (2006) 757–762. doi:10.4028/www.scientific.net/MSF.503-504.757.
14.
PolyakovA. V., SemenovaI.P., ValievRuslan Z., Influence of annealing on ductility of ultra fine-grained titanium processed by equal-channel angular pressing – Conform and drawing, MRS Commun. 3 (2013) 249–253. doi:10.1557/mrc.2013.40.
15.
ArabiH., KetabchiM., AlhosseiniS.H.N., Details of mechanical and microstructural variations in ECAP of Ti-6Al-4V alloy with equiaxed microstructure, Rare Met. In Press (2018). doi:10.1007/s12598-018-1071-5.
16.
AlabortE., KontisP., BarbaD., DragnevskiK., ReedR.C., On the mechanisms of superplasticity in Ti-6Al-4V, Acta Mater. 105 (2016) 449–463. doi:10.1016/j.actamat.2015.12.003.
17.
SalishchevG.A., KudrjavtsevE.A., ZherebtsovS. V, SemiatinS.L., Low temperature superplasticity of Ti-6Al-4V processed by warm multidirectional forging, Mater Sci Forum. 735 (2013) 253–258. doi:10.4028/www.scientific.net/MSF.735.253.
18.
SemenovaI.P., ModinaJ.M., AlexanderV., KlevtsovG. V, NatalyA., PigalevaI.N., ValievR.Z., LangdonT.G., Fracture toughness at cryogenic temperatures of ultrafine-grained Ti-6Al-4V alloy processed by ECAP, Mater Sci Eng A. (2017). doi:10.1016/j.msea.2017.12.106.
19.
MukhametrakhimovM.K., The influence of the surface roughness of sheet billets of titanium alloys VT6 on quality of the solid state joining under low temperature superplasticity conditions, Rev Adv Mater Sci. 31 (2012) 174–178.
20.
MayL.Mechanical properties of ultrafine-grained Ti-6Al-4V ELI alloy processed by severe plastic deformation. PHD Thesis. Erlangen: Univ. Erlangen-Nürnb; 2009.
21.
MiaoquanL.I., ChenZ., JiaoL.U.O., MingwangF.U., Thermomechanical coupling simulation and experimental study in the isothermal ECAP processing of Ti-6Al-4V alloy, Rare Met. 29 (2010) 613–620. doi:10.1007/s12598-010-0180-6.
22.
GunY., YoungD., HyukD., LeeS., SooC., Factors influencing the equal-channel angular pressing of Ti – 6Al – 4V alloy having lamellar microstructure, Mater Sci Eng A. 493 (2008) 164–169. doi:10.1016/j.msea.2007.06.091.
23.
KumarP., KawasakiM., LangdonT.G., Review: Overcoming the paradox of strength and ductility in ultrafine-grained materials at low temperatures, J Mater Sci. 51 (2015) 7–18. doi:10.1007/s10853-015-9143-5.
24.
LiZ., FuL., FuB., ShanA., Effects of annealing on microstructure and mechanical properties of nano-grained titanium produced by combination of asymmetric and symmetric rolling, Mater Sci Eng A. 558 (2012) 309–318. doi:10.1016/j.msea.2012.08.005.
25.
SalishchevF. H. F. G. A., ValiakhmetovO. R., GaleyevR. M.Characterization of submicron-grained Ti-6AI-4V sheets with enhanced superplastic properties. Mater Sci Forum. 2004;447–448:6–11.
26.
ValievR.Z., EstrinY., HoritaZ., LangdonT.G., ZehetbauerM.J., Producing bulk ultrafine-grained materials by severe plastic deformation: ten years later, JOM. 68 (2016) 1216–1226. doi:10.1007/s11837-016-1820-6.
27.
LangdonT.G., Correlation between microstructure and mechanical properties of severely deformed metals, J Alloy Compd J. 483 (2009) 271–274. doi:10.1016/j.jallcom.2008.07.200.
28.
ZhuY.T., LoweT.C., LangdonT.G., Performance and applications of nanostructured materials produced by severe plastic deformation, Scr Mater. 51 (2004) 825–830. doi:10.1016/j.scriptamat.2004.05.006.
