The influence of strain rates on the indentation size effect (ISE) was explored experimentally. A strong ISE phenomenon on the hardness of Ti–10V–2Fe–3Al (Ti-1023) alloy was found when the peak-load was less than 3500 mN, regardless of the variation of loading rates. However, as indenter strain rates increased, the degree of ISE reduced considerably, which was related to the decrease of the internal indentation length scale ranging from 23.08 to 6.80 µm. Furthermore, a positive strain rate sensitivity of the hardness in the whole peak-load range was found in Ti-1023 alloy, which showed a linear function of indenter load. The underlying mechanism was well explained by the variation of geometrically necessary dislocation and statistically stored dislocations in Ti-1023 alloy.
AshtonPJ, JunT-S, ZhangZ, The effect of the beta phase on the micromechanical response of dual-phase titanium alloys. Int J Fatigu. 2017;100:377–387. doi: 10.1016/j.ijfatigue.2017.03.020
2.
AkanumaT, MatsumotoH, SatoS, Enhancement of athermal α″martensitic transformation in Ti–10V–2Fe–3Al alloy due to high-speed hot deformation. Scripta Mater. 2012;67:21–24. doi: 10.1016/j.scriptamat.2012.03.011
3.
CaiJ, LiF, LiuT, Microindentation study of Ti–6Al–4 V alloy. Mater Design. 2011;32:2756–2762. doi: 10.1016/j.matdes.2011.01.003
4.
LeiX, DongL, ZhangZ, Microtexture and nanoindentation of α and β Phases in Ti–6Al–1.5 Cr–2.5 Mo–0.5 Fe–0.3 Si titanium alloy. Sci Adv Mater. 2017;9:1476–1483. doi: 10.1166/sam.2017.3154
5.
Ehtemam-HaghighiS, CaoG, ZhangL-C.Nanoindentation study of mechanical properties of Ti based alloys with Fe and Ta additions. J Alloy Compd. 2017;692:892–897. doi: 10.1016/j.jallcom.2016.09.123
6.
HaghshenasM.Multi-cycling instrumented nanoindentation of a Ti-23Nb-0.7 Ta-2Zr-1.2 O alloy in annealed condition. Mater Sci Eng A-Struct. 2017;697:8–16. doi: 10.1016/j.msea.2017.05.004
7.
PharrGM, HerbertEG, GaoY.The indentation size effect: a critical examination of experimental observations and mechanistic interpretations. Annu Rev Mater Res. 2010;40:271–292. doi: 10.1146/annurev-matsci-070909-104456
8.
NixWD, GaoH.Indentation size effects in crystalline materials: a law for strain gradient plasticity. J Mec Phys Solids. 1998;46:411–425. doi: 10.1016/S0022-5096(97)00086-0
HurákováM, CsachK, JuríkováA, Influence of loading rate on the mechanical performance of metallic glass. J Non-Cryst Solids. 2017;470:160–167. doi: 10.1016/j.jnoncrysol.2017.05.023
14.
MaierV, SchunkC, GökenM, Microstructure-dependent deformation behaviour of bcc-metals–indentation size effect and strain rate sensitivity. Philos Mag. 2015;95:1766–1779. doi: 10.1080/14786435.2014.982741
15.
ChenJ, ShenY, LiuW, Effects of loading rate on development of pile-up during indentation creep of polycrystalline copper. Mater Sci Eng A-Struct. 2016;656:216–221. doi: 10.1016/j.msea.2016.01.042
16.
HaghshenasM, WangY, ChengY-T, Indentation-based rate-dependent plastic deformation of polycrystalline pure magnesium. Mater Sci Eng A-Struct. 2018;716:63–71. doi: 10.1016/j.msea.2018.01.036
17.
HuJ, SunW, JiangZ, Indentation size effect on hardness in the body-centered cubic coarse-grained and nanocrystalline tantalum. Mater Sci Eng A-Struct. 2017;686:19–25. doi: 10.1016/j.msea.2017.01.033
18.
BhattacharyyaA, SinghG, PrasadKE, On the strain rate sensitivity of plastic flow in metallic glasses. Mater Sci Eng A-Struct. 2015;625:245–251. doi: 10.1016/j.msea.2014.12.004
19.
Van SteenbergeN, SortJ, ConcustellA, Dynamic softening and indentation size effect in a Zr-based bulk glass-forming alloy. Scripta Mater. 2007;56:605–608. doi: 10.1016/j.scriptamat.2006.12.014
20.
MaX, LiF, ZhaoC, Indenter load effects on creep deformation behavior for Ti-10V-2Fe-3Al alloy at room temperature. J Alloy Compd. 2017;709:322–328. doi: 10.1016/j.jallcom.2017.03.175
21.
PanD, InoueA, SakuraiT, Experimental characterization of shear transformation zones for plastic flow of bulk metallic glasses. P Natl Acad Sci USA. 2008;105:14769–14772. doi: 10.1073/pnas.0806051105
22.
LucasB, OliverW.Indentation power-law creep of high-purity indium. Metall Mater Trans A. 1999;30:601–610. doi: 10.1007/s11661-999-0051-7
OliverWC, PharrGM.An improved technique for determining hardness and elastic modulus using load and displacement sensing indentation experiments. J Mater Res. 1992;7:1564–1583. doi: 10.1557/JMR.1992.1564
25.
LiuY, TeoJ, TungS, High-temperature creep and hardness of eutectic 80Au/20Sn solder. J Alloy Compd. 2008;448:340–343. doi: 10.1016/j.jallcom.2006.12.142
26.
ChoiI-C, KimY-J, WangYM, Nanoindentation behavior of nanotwinned Cu: influence of indenter angle on hardness, strain rate sensitivity and activation volume. Acta Mater. 2013;61:7313–7323. doi: 10.1016/j.actamat.2013.08.037
27.
DurstK, BackesB, FrankeO, Indentation size effect in metallic materials: modeling strength from pop-in to macroscopic hardness using geometrically necessary dislocations. Acta Mater. 2006;54:2547–2555. doi: 10.1016/j.actamat.2006.01.036
28.
DurstK, BackesB, GökenM.Indentation size effect in metallic materials: correcting for the size of the plastic zone. Scripta Mater. 2005;52:1093–1097. doi: 10.1016/j.scriptamat.2005.02.009
FrankeO, TrenkleJC, SchuhCA.Temperature dependence of the indentation size effect. J Mater Res. 2010;25:1225–1229. doi: 10.1557/JMR.2010.0159
32.
BackesB, DurstK, GoekenM.Determination of plastic properties of polycrystalline metallic materials by nanoindentation: experiments and finite element simulations. Philos Mag. 2006;86:5541–5551. doi: 10.1080/14786430600735468
33.
SeokMY, KimYJ, ChoiIC, Predicting flow curves of two-phase steels from spherical nanoindentation data of constituent phases: isostrain method vs. non-isostrain method. Int J Plasticity. 2014;59:108–118. doi: 10.1016/j.ijplas.2014.03.013
34.
WangX, ZhanM, GaoP, Micromechanical behaviour of TA15 alloy cylindrical parts processed by multi-pass flow forming. Mater Sci Eng A Struct. 2018;737:328–335. doi: 10.1016/j.msea.2018.09.062
35.
ChrobakD, KimK-H, KurzydłowskiK, Nanoindentation experiments with different loading rate distinguish the mechanism of incipient plasticity. Appl Phys Lett. 2013;103:072101. doi: 10.1063/1.4818260
36.
ElmustafaA, StoneD.Nanoindentation and the indentation size effect: kinetics of deformation and strain gradient plasticity. J Mech Phy Solids. 2003;51:357–381. doi: 10.1016/S0022-5096(02)00033-9
37.
VoyiadjisGZ, FaghihiD.Microstructure to macro-scale using gradient plasticity with temperature and rate dependent length scale. Procedia IUTAM. 2012;3:205–227. doi: 10.1016/j.piutam.2012.03.014
