In the present investigation, tribological behaviour of the hot extruded Al–Cu–Mg–Ag (matrix) alloy and the effect of Ti and TiB2 addition in matrix alloy have been studied. Hot extrusion was introduced to eliminate cast defects like porosity, voids and micro cracks. Addition of Ti and TiB2 particles increased the hardness of the matrix by grain refinement and dispersion hardening, respectively. It has been observed that the increase in hardness had significantly improved the wear resistance of the material. Detail study of the wear surfaces and debris were carried out to understand the wear mechanism of the samples. It revealed a complex mechanism of micro-cutting, plastic deformation, abrasion and delamination of the wear samples.
LakshmiS, LuL, GuptaM.In situ preparation of TiB2 reinforced Al-based composites. J Mater Process Technol. 1998;73:160–166. doi: 10.1016/S0924-0136(97)00225-2
2.
TeeKL, LuL, LaiMO.In situ processing of Al-TiB2 composite by the stir-casting technique. J Mater Process Technol. 1999;89–90:513–519. DOI:10.1016/S0924-0136(99)00038-2.
3.
KumarS, ChakrabortyM, Subramanya SarmaV, Tensile and wear behaviour of in situ Al-7Si/TiB2 particulate composites. Wear. 2008;265:134–142. DOI:10.1016/j.wear.2007.09.007.
4.
SureshS, ShenbagaN, MoV, Tribological, tensile and hardness behavior of TiB2 reinforced aluminium metal matrix composite. J Balk Tribol Assoc. 2014;20:380–394.
5.
EmamyM, MahtaM, RasizadehJ.Formation of TiB2 particles during dissolution of TiAl3 in Al-TiB2 metal matrix composite using an in situ technique. Compos Sci Technol. 2006;66:1063–1066. DOI:10.1016/j.compscitech.2005.04.016.
6.
HashimJ, LooneyL, HashmiMSJ.Metal matrix composites: production by the stir casting method. J Mater Process Technol. 1999;92–93:1–7. doi: 10.1016/S0924-0136(99)00118-1
7.
RameshC, HirianiahA, HarishanadK, A review on hot extrusion of metal matrix composites (MMC's). Int J Eng Sci. 2012;1:30–35.
8.
VivekanandaAS, Balasivanandha PrabuS, PaskaramoorthyR.Combined effect of process parameters during aluminothermic reaction process on the microstructure and mechanical properties of in situ Al/TiB2 composite. J Alloys Compd. 2018;735:619–634. DOI:10.1016/j.jallcom.2017.11.167.
9.
NatarajanS, NarayanasamyR, Kumaresh BabuSP, Sliding wear behaviour of Al 6063/TiB2 in situ composites at elevated temperatures. Mater Des. 2009;30:2521–2531. DOI:10.1016/j.matdes.2008.09.037.
10.
HerbertMA, MaitiR, MitraR, Wear behaviour of cast and mushy state rolled Al-4.5Cu alloy and in-situ Al4.5Cu-5TiB2composite. Wear. 2008;265:1606–1618. DOI:10.1016/j.wear.2008.03.010.
11.
SureshS, Shenbaga Vinayaga MoorthiN, VettivelSC, Mechanical behavior and wear prediction of stir cast Al-TiB2composites using response surface methodology. Mater Des. 2014;59:383–396. DOI:10.1016/j.matdes.2014.02.053.
12.
Chapter 3, Production and characterization of Al-TiB2, Introduction, p. 51–78.
13.
PramodSL, BakshiSR, MurtyBS.Aluminum-based cast in situ composites: a review. J Mater Eng Perform. 2015;24:2185–2207. DOI:10.1007/s11665-015-1424-2.
14.
NieJ, WangF, LiY, Microstructure evolution and mechanical properties of Al-TiB2/TiC in situ aluminum-based composites during accumulative roll bonding (ARB) process. Materials (Basel). 2017;10. DOI:10.3390/ma10020109.
15.
VenkatesanS, XaviorMA.Comparative analysis of aluminium metal matrix composites reinforced with TiC and TiB2 using stir casting process. Int J Sci Res Eng Stud. 2015;2:61–65.
16.
LiZG.Fabrication of in situ TiB2 particulates reinforced zinc alloy matrix composite. Mater Lett. 2014;121:1–4. DOI:10.1016/j.matlet.2014.01.050.
17.
ŠkolA, NovP, MejzlL, Structure and mechanical properties of Al-Cu-Fe-X alloys with excellent thermal stability. Materials. 2017;10:1269. DOI:10.3390/ma10111269.
18.
FengCF, FroyenL.Microstructures of in situ Al/TiB2MMCs prepared by a casting route. J Mater Sci. 2000;35:837–850. DOI:10.1023/A:1004729920354.
19.
ArchardJF.Contact and rubbing of flat surfaces. J Appl Phys. 1953;24:981–988. DOI:10.1063/1.1721448.
20.
SampathV, RajasekaranN.R.Effect of in-situ titanium boride particle addition and friction stir processing on wear behavior of aluminum alloy 2219; TMS2015 1441h Annual Meeting & Exhibition conference proceeding edited by T. Sano, T. S. Srivatsan: Adv Compos Aerosp Mar Land Appl II; 2015.
21.
CaracostasCA, ChiouWA, FineME, Tribological properties of aluminum alloy matrix TiB2 composite prepared by in-situ processing. Metall Mater Trans A. 1997;28:491–502. doi: 10.1007/s11661-997-0150-2
22.
PoriaS, SahooP, SutradharG.Wear performance optimization of stir cast Al-TiB2 metal matrix composites using Taguchi design of experiments wear performance optimization of stir cast Al-TiB2 metal matrix composites using Taguchi design of experiments; 2016. DOI:10.1088/1757-899X/149/1/012085.
