Residual stresses were characterised in a wire-feed additively manufactured titanium alloy component. A numerical simulation based on the inherent strain method was used to model residual stresses arising from the manufacturing process. The contour method was used to experimentally determine the residual stress field. High tensile residual stresses were seen at and around the interface of the substrate and the deposited metal. Compressive residual stresses were present in the substrate and at the top of the deposit. The satisfactory correlation was achieved between the results from the numerical simulation and the contour method, except for the location of the root of the deposit. The effect of pre-heating the sample substrate on the residual stress distribution is also discussed.
DuttaB, FroesFH.The additive manufacturing (AM) of titanium alloys. Met Powder Rep. 2017;72:96–106. doi: 10.1016/j.mprp.2016.12.062
2.
LevyLN, SchindelR, KruthJP.Rapid manufacturing and rapid tooling with layer manufacturing (LM) technologies, state of the art and future perspectives. CIRP Annals. 2003;52:589–609. doi: 10.1016/S0007-8506(07)60206-6
3.
LiP, WarnerDH, FatemiA, Critical assessment of fatigue performance of additively manufactured Ti-6Al-4V and perspective for future research. Int J Fatigue. 2016;85:130–143. doi: 10.1016/j.ijfatigue.2015.12.003
4.
DebRoyT, WeiHL, ZubackJS, Additive manufacturing of metallic components-process, structure and properties. Progr Materi Sci. 2018;92:112–224. doi: 10.1016/j.pmatsci.2017.10.001
5.
MartinaF, RoyMJ, SzostBA, Residual stress of as-deposited and rolled wire + arc additive manufacturing Ti-6Al-4V components. Mater Sci Technol. 2016;32:1439–1448. doi: 10.1080/02670836.2016.1142704
6.
BaufeldB, BrandlE, van der BiestO.Wire based additive layer manufacturing: comparison of microstructure and mechanical properties of Ti-6Al-4V components fabricated by laser-beam deposition and shaped metal deposition. J Mater Process. Technol. 2011;211:1146–1158. doi: 10.1016/j.jmatprotec.2011.01.018
7.
DingD, PanZ, CuiuriD, Wire-feed additive manufacturing of metal components: technologies, developments and future interests. Int J Adv Manuf. Technol. 2015;81:465–481. doi: 10.1007/s00170-015-7077-3
8.
HönnigeJR, WilliamsS, RoyMJ, Residual stress characterization and control in the additive manufacture of large scale metal structures. Mater Res Proc. 2016;2:455–460.
9.
SzostBA, TerziS, MartinaF, A comparative study of additive manufacturing techniques: residual stress and microstructural analysis of CLAD and WAAM printed Ti-6Al-4V components. Mater Des. 2016;89:559–567. doi: 10.1016/j.matdes.2015.09.115
10.
MartinaF, ColegrovePA, WilliamsSW, Microstructure of interpass rolled wire + arc additive manufacturing Ti-6Al-4V components. Metall Trans A. 2015;46:6103–6118. doi: 10.1007/s11661-015-3172-1
11.
DenlingerE.Thermo-mechanical model development and experimental validation of metallic parts in additive manufacturing [dissertation]. Pennsylvania: The Pennsylvania State University; 2015.
12.
FujimotoT.A method for analysis of residual welding stresses and deformations based on the inherent strain. J Jpn Weld Soc. 1970;39:236–252. doi: 10.2207/qjjws1943.39.4_236
13.
UedaY, FukudaK, NakachoK, A new measuring method of residual stresses with the aid of finite element method and reliability of estimated values. Trans JWRI. 1975;4:123–131. doi: 10.1007/BF00164683
14.
UedaY, YuanMG.A predicting method of welding residual using source of residual stress (report III). Trans JWRI. 1993;22:157–168.
15.
AhmadB, Van-der-VeenSO, FitzpatrickME, Residual stress evaluation in selective-laser-melting additively manufactured titanium (Ti-6Al-4V) and inconel 718 using the contour method and numerical simulation. Add Manuf. 2018;22:571–582.
16.
PrabhakarP, SamesWJ, DehoffR, Computational modelling of residual stress formation during the electron beam melting process for Inconel 718. Addit Manuf. 2015;7:83–91. doi: 10.1016/j.addma.2015.03.003
17.
PrimeMB.Cross-sectional mapping of residual stresses by measuring the surface contour after a cut. J Eng Mater Technol. 2001;123:162–168. doi: 10.1115/1.1345526
18.
AhmadB, FitzpatrickME.Residual stresses in ultrasonically peened fillet welded joints. Adv Mater Res. 2014;996:755–760.
19.
AhmadB, FitzpatrickME.Analysis of residual stresses in laser-shock-peened and shot-peened marine steel welds. Metall Mater Trans A. 2017;48:759–770. doi: 10.1007/s11661-016-3867-y
20.
AhmadB, FitzpatrickME.Minimization and mitigation of wire EDM cutting errors in the application of the contour method of residual stress measurement. Metall Mater Trans A. 2016;47:301–313. doi: 10.1007/s11661-015-3231-7
21.
HosseinzadehF, TraoreY, BouchardPJ, Mitigating cutting-induced plasticity in the contour method (part 1, experimental). Exp Mech. 2016;94-95:247–25.
22.
MuranskyO, HamelinCJ, HosseinzadehF, Evaluation of self-equilibrium cutting strategy for the contour method of residual stress measurement. Int J Pressure Ves Pipe. 2017. DOI:10.1016/j.ijpvp.2017.04.002.
23.
ToparliMB, FitzpatrickME, GungorS.Determination of multiple near-surface residual stress components in laser peened aluminium alloy via the contour method. Metall Mater Trans A. 2015;46:4268–4275. doi: 10.1007/s11661-015-3026-x
24.
ZhangJ, WangX, PaddeaS, Fatigue crack propagation behaviour in wire + arc additive manufactured T-6Al-4V: effects of microstructure and residual stress. Mater Des. 2016;90:551–561. doi: 10.1016/j.matdes.2015.10.141
25.
JohnsonG.Residual stress measurement using contour method [dissertation]. Manchester: The University of Manchester; 2008.
26.
KellerN, PloshikhinV.New method for fast predictions of residual stress and distortion of AM parts. Annu Int Solid Freeform Fab Symp. 2014:1229–1237.
27.
CaoJ, GharghouriMA, NashP.Finite-element analysis and experimental validation of thermal residual stress and distortion in electron beam additive manufactured Ti-6Al-4V build plates. J Mater Process Technol. 2016;237:409–419. doi: 10.1016/j.jmatprotec.2016.06.032
28.
ColegrovePA, CoulesHE, FairmanJ, Microstructure and residual stress improvement in wire and arc additively manufactured parts through high pressure rolling. J Mater Process Technol. 2013;213:1782–1791. doi: 10.1016/j.jmatprotec.2013.04.012
