The microstructure and mechanical properties of a Cu–Cr–Ag alloy at the different processing stages were investigated using hardness measurements, scanning electron microscopy, and transmission electron microscopy. The combined effects of dislocation strengthening and precipitation strengthening were shown to remarkably enhance the hardness of the alloy. Coherent Cr-rich precipitates with a face-centred cubic structure, formed during aging, were shown to be the main source of age strengthening, and the introduction of pre-deformation led to acceleration of their precipitation. Nevertheless, recovery occurring during aging caused significant softening in the cold-drawn samples. Analysis of the microstructural evolution during cold drawing and aging was used as an effective tool to optimise the thermomechanical process and improve the mechanical properties.
MorozovaA, KaibyshevR.Grain refinement and strengthening of a Cu–0.1Cr–0.06Zr alloy subjected to equal channel angular pressing. Philos Mag. 2017;97(24):2053–2076. doi: 10.1080/14786435.2017.1324649
2.
KrishnaSC, RaoGS, JhaAK, Strengthening in high strength Cu–Cr–Zr–Ti alloy plates produced by hot rolling. Mater Sci Eng A. 2016;674:164–170. doi: 10.1016/j.msea.2016.07.063
3.
WatanabeC, MonzenR, TazakiK.Mechanical properties of Cu–Cr system alloys with and without Zr and Ag. J Mater Sci. 2008;43(3):813–819. doi: 10.1007/s10853-007-2159-8
4.
AbibK, AzzeddineH, TirsatineK, Thermal stability of Cu–Cr–Zr alloy processed by equal-channel angular pressing. Mater Charact. 2016;118:527–534. doi: 10.1016/j.matchar.2016.07.006
5.
FuYB, CuiJ.Preparation of Cu–Cr–Zr alloy billets by horizontal electromagnetic continuous stirring. Mater Sci Technol. 2014;30(3):370–376. doi: 10.1179/1743284713Y.0000000321
6.
ZhangPC, JieJC, GaoY, Influence of cold deformation and Ti element on the microstructure and properties of Cu–Cr system alloys. J Mater Res. 2015;30(13):2073–2080. doi: 10.1557/jmr.2015.143
7.
JiaSG, ZhengMS, LiuP, Aging properties studies in a Cu–Ag–Cr alloy. Mater Sci Eng A. 2006;419(1–2):8–11. doi: 10.1016/j.msea.2005.09.118
8.
IslamgalievRK, NesterovKM, BourgonJ, Nanostructured Cu–Cr alloy with high strength and electrical conductivity. J Appl Phys. 2014;115(19):1943011–1943014. doi: 10.1063/1.4874655
9.
MahmudiR, KarsazA, Akbari-FakhrabadiA, Impression creep study of a Cu–0.3Cr–0.1Ag alloy. Mater Sci Eng A. 2010;527(10-11):2702–2708. doi: 10.1016/j.msea.2010.01.044
10.
ZhilyaevAP, ShakhovaI, MorozovaA, Grain refinement kinetics and strengthening mechanisms in Cu–0.3Cr–0.5Zr alloy subjected to intense plastic deformation. Mater Sci Eng A. 2016;654:131–142. doi: 10.1016/j.msea.2015.12.038
11.
ChengJY, ShenB, YuFX.Precipitation in a Cu–Cr–Zr–Mg alloy during aging. Mater Charact. 2013;81(4):68–75. doi: 10.1016/j.matchar.2013.04.008
12.
RdzawskiZ, StobrawaJ.Structure of coherent chromium precipitates in aged copper alloys. Scripta Metall. 1986;20(3):341–344. doi: 10.1016/0036-9748(86)90154-7
13.
ChbihiA, SauvageX, BlavetteD.Atomic scale investigation of Cr precipitation in copper. Acta Mater. 2012;60(11):4575–4585. doi: 10.1016/j.actamat.2012.01.038
14.
XiaCD, ZhangW, KangZY, High strength and high electrical conductivity Cu–Cr system alloys manufactured by hot rolling-quenching process and thermomechanical treatments. Mater Sci Eng A. 2012;538:295–301. doi: 10.1016/j.msea.2012.01.047
15.
BatraIS, DeyGK, KulkarniUD, Precipitation in a Cu–Cr–Zr alloy. Mater Sci Eng A. 2003;356(1-2):32–36. doi: 10.1016/S0921-5093(02)00852-3
16.
ChenHB, LiuTM, YuHN, Dependence of microstructure and hardening behavior on torsion strain and strain rate in extruded AZ31 rods. Adv Eng Mater. 2016;18(9):1683–1689. doi: 10.1002/adem.201600219
17.
XiaCD, JiaYL, ZhangW, Study of deformation and aging behaviors of a hot rolled–quenched Cu–Cr–Zr–Mg–Si alloy during thermomechanical treatments. Mater Des. 2012;39:404–409. doi: 10.1016/j.matdes.2012.03.003
18.
ChbihiA, SauvageX, BlavetteD.Influence of plastic deformation on the precipitation of Cr in copper. JMater Sci. 2014;49(18):6240–6247. doi: 10.1007/s10853-014-8348-3
19.
YuanDW, YangB, ChenJS, Upward continuous casting in the manufacture of Cu–Cr–Ag alloys: potential for enhancing strength whilst maintaining ductility. Metall Mater Trans A. 2017;48(12):6083–6090. doi: 10.1007/s11661-017-4338-9
20.
RyuHJ, BaikHK, HongSH.Effect of thermomechanical treatments on microstructure and properties of Cu-base leadframe alloy. J Mater Sci. 2000;35(14):3641–3646. doi: 10.1023/A:1004830000742
21.
YouXG, TanY, LiJY, Effects of solution heat treatment on the microstructure and hardness of Inconel 740 superalloy prepared by electron beam smelting. J Alloy Compd. 2015;638:239–248. doi: 10.1016/j.jallcom.2015.03.075
22.
JedrychowskiM, TarasiukJ, BacroixB, Electron backscatter diffraction investigation of local misorientations and orientation gradients in connection with evolution of grain boundary structures in deformed and annealed zirconium. A new approach in grain boundary analysis. J Appl Crystallogr. 2013;46(2):483–492. doi: 10.1107/S0021889812052016
23.
LuYP, MolodovDA, GottsteinG.Recrystallization kinetics and microstructure evolution during annealing of a cold-rolled Fe-Mn-C alloy. Acta Mater. 2011;59(8):3229–3243. doi: 10.1016/j.actamat.2011.01.063
24.
ChengH, WangHY, XieYC, Controllable fabrication of a carbide-containing FeCoCrNiMn high-entropy alloy: microstructure and mechanical properties. Mater Sci Technol. 2017;33(17):2032–2039. doi: 10.1080/02670836.2017.1342367
25.
ZhaoYH, LiaoXZ, JinZ, Microstructures and mechanical properties of ultrafine grained 7075 Al alloy processed by ECAP and their evolutions during annealing. Acta Mater. 2004;52:4589–4599. doi: 10.1016/j.actamat.2004.06.017
26.
ChenXB, JiangF, LiuLL, Structure and orientation relationship of new precipitates in a Cu–Cr–Zr alloy. Mater Sci Technol. 2018;34(3):282–288. doi: 10.1080/02670836.2017.1376428
27.
BatraIS, DeGK, KulkarniUD, Microstructure and properties of a Cu–Cr–Zr alloy. J Nucl Mater. 2001;299(2):91–100. doi: 10.1016/S0022-3115(01)00691-2
28.
KuoCM, LinCS.Static recovery activation energy of pure copper at room temperature. Scripta Mater. 2007;57(8):667–670. doi: 10.1016/j.scriptamat.2007.06.054
29.
WeiKW, WeiW, WangF, Microstructure, mechanical properties and electrical conductivity of industrial Cu–0.5%Cr alloy processed by severe plastic deformation. Mater Sci Eng A. 2011;528(3):1478–1484. doi: 10.1016/j.msea.2010.10.059
30.
D'AntuonoDS, GaiesJ, GolumbfskieW, Direct measurement of the effect of cold rolling on β phase precipitation kinetics in 5xxx series aluminum alloys. Acta Mater. 2017;123:264–271. doi: 10.1016/j.actamat.2016.10.060
31.
BakerI.Recovery, recrystallization and grain growth in ordered alloys. Intermetallics. 2000;8(9–11):1183–1196. doi: 10.1016/S0966-9795(00)00031-5
