A Cu–0.24Mg alloy bar was treated by internal oxidation using Cu2O as an oxidiser at 1123–1273 K for 10 h. The thermodynamic diagram for oxidation of a Cu–Mg alloy was confirmed by the critical oxygen pressure. The results show that the thickness of the MgO/Cu layer and the electrical conductivity of the Cu–0.24Mg alloy increase with increasing internal oxidation temperature, whereas the average hardness of the MgO/Cu layer initially increases and subsequently decreases. Examination of the microstructure of the MgO/Cu layer revealed that Mg precipitation in the form of MgO particles and their uniform dispersion in the Cu matrix were the primary reasons for increases in the comprehensive properties of the Cu–Mg alloy treated by internal oxidation.
GuoX, SongK, LiangS, Effect of Al2O3 particle size on electrical wear performance of Al2O3 Cu composites. Tribol Trans. 2016;59(1):170–177. doi: 10.1080/10402004.2015.1061079
2.
RenFZ, ZhiAJ, ZhangDW, Preparation of Cu–Al2O3 bulk nano-composites by combining Cu–Al alloy sheets internal oxidation with hot extrusion. JAlloys Compd. 2015;633:323–328. doi: 10.1016/j.jallcom.2015.02.057
3.
YinJ, ZhangH, TanC, Effect of heat treatment temperature on sliding wear behaviour of C/C-Cu composites under electric current. Wear2014;312(1–2):91–95. doi: 10.1016/j.wear.2014.01.001
4.
ChenG, YangW, DongR, Interfacial microstructure and its effect on thermal conductivity of SiCp/Cu composites. Mater Des. 2014;63:109–114. doi: 10.1016/j.matdes.2014.05.068
5.
SelvakumarN, VettivelSC.Thermal, electrical and wear behavior of sintered Cu–W nanocomposite. Mater Des. 2013;46:16–25. doi: 10.1016/j.matdes.2012.09.055
6.
GuoX, SongK, LiangS, Effect of the thermal expansion characteristics of reinforcements on the electrical wear performance of copper matrix composite. Tribol Trans. 2014;57(2):283–291. doi: 10.1080/10402004.2013.870271
7.
ZhengR, ZhanZ, WangW.Tribological properties of Cu-La2O3 composite under different electrical currents. J Rare Earths. 2011;29(3):247–252. doi: 10.1016/S1002-0721(10)60440-1
8.
RitasaloR, LiuaXW, SöderbergO, The microstructural effects on the mechanical and thermalproperties of pulsed electric current sintered Cu-Al2O3 composites. Procedia Eng. 2011;10:124–129. doi: 10.1016/j.proeng.2011.04.023
9.
GrozaJR, GibelingJC.Principles of particle selection for dispersion-strengthened copper. Mater Sci Eng A. 1993;171(1–2):115–125. doi: 10.1016/0921-5093(93)90398-X
10.
LiangS, FangL, FanZ.Internal oxidation of Cr in Cu–Cr/Cu2O composite powder prepared by mechanical activation. Mater Sci Eng A. 2004;374(1–2):27–33. doi: 10.1016/j.msea.2003.09.082
11.
TjongS, WangG.Low-cycle fatigue behavior of in situ TiB2/Cu composite prepared by reactive hot pressing. J Mater Sci. 2006;41(16):5263–5268. doi: 10.1007/s10853-006-0333-z
12.
SongK, GuoX, LiangS, Relationship between interfacial stress and thermal expansion coefficient of copper–matrix composites with different reinforced phases. Mater Sci Technol. 2014;30(2):171–175. doi: 10.1179/1743284713Y.0000000332
13.
GuoX, SongK, LiangS, Effect of the thermal expansion characteristics of reinforcements on the electrical wear performance of copper matrix composite. Tribol Trans. 2014;57(2):283–291. doi: 10.1080/10402004.2013.870271
14.
GuoX, SongK, LiangS, Thermal expansion behavior of MgO/Cu composite with lower MgO volume fraction. Mater Res Bull. 2012;47(11):3211–3215. doi: 10.1016/j.materresbull.2012.08.012
15.
HuangS, FengY, LiuH, Electrical sliding friction and wear properties of Cu–MoS2–graphite–WS2 nanotubes composites in air and vacuum conditions. Mater Sci Eng A. 2013;560:685–692. doi: 10.1016/j.msea.2012.10.014
16.
ShojaeepourF, AbachiP, PurazrangK, Production and properties of Cu/Cr2O3 nano-composites. Powder Technol. 2012;222:80–84. doi: 10.1016/j.powtec.2012.02.001
17.
SongK, XingJ, DongQ, Internal oxidation of dilute Cu–Al alloy powers with oxidant of Cu2O. Mater Sci Eng A. 2004;380(1–2):117–122. doi: 10.1016/j.msea.2004.03.042
18.
WatanabeK, KunisadaY, SakaguchiN.Stability of {111}Pd/{0002}ZnO polar interface formed by internal oxidation of Pd–Zn alloys. Microscopy. 2014;63(6):463–467. doi: 10.1093/jmicro/dfu095
19.
BalanovicL, CosovicV, TalijanN, Mater Tehnol. 2013;47(4):447–452.
20.
WangYG, ZhangZ, YanGH, J Mater Sci. 2002;37(12):2511–2518. doi: 10.1023/A:1015439624193
21.
VargaM, MolnárÁ, MulasG, Cu–MgO samples prepared by mechanochemistry for catalytic application. J Catal. 2002;206(1):71–81. doi: 10.1006/jcat.2001.3476
22.
MullerDA, ShashkovDA, BenedekR, Atomic scale observations of metal-induced gap states at {222} MgO/Cu interfaces. Phys Rev Lett. 1998;80(21):4741–4744. doi: 10.1103/PhysRevLett.80.4741
23.
BirksN, MeierGH.Introduction to high temperature oxidation of metals. London: Edward Arnold; 1983.
24.
TianYZ, ZhangZF.Stability of interfaces in a multilayered Ag–Cu composite during cold rolling. Scr Mater. 2013;68(7):542–545. doi: 10.1016/j.scriptamat.2012.12.014
25.
ChuK, JiaC, JiangL, Improvement of interface and mechanical properties in carbon nanotube reinforced Cu–Cr matrix composites. Mater Des. 2013;45:407–411. doi: 10.1016/j.matdes.2012.09.027
26.
ShorowordiKM, LaouiT, HaseebASMA, Microstructure and interface characteristics of B4C, SiC and Al2O3 reinforced Al matrix composites: a comparative study. J Mater Process Technol. 2003;142(3):738–743. doi: 10.1016/S0924-0136(03)00815-X
27.
SpeightMV.Growth kinetics of grain-boundary precipitates. Acta Metall. 1968;16(1):133–135. doi: 10.1016/0001-6160(68)90081-3
28.
SongK, XingJ, DongQ, Optimization of the processing parameters during internal oxidation of Cu–Al alloy powders using an artificial neural network. Mater Des. 2005;26(4):337–341. doi: 10.1016/j.matdes.2004.06.002
29.
RuihuaL, KexingS, ShuguoJ, Morphology and frictional characteristics under electrical currents of Al2O3/Cu composites prepared by internal oxidation. Chin J Aeronaut. 2008;21(3):281–288. doi: 10.1016/S1000-9361(08)60037-0
30.
SongKX, LiuP, TianBH, Stabilization of nano-Al2O3p/Cu composite after high temperature annealing treatment. Mater Sci Forum. 2005;475–479:993–996. doi: 10.4028/www.scientific.net/MSF.475-479.993
31.
GrozaJ.Heat-resistant dispersion-strengthened copper alloys. J Mater Eng Perform. 1992;1(1):113–121. doi: 10.1007/BF02650042
