The effects of a homogenisation treatment on precipitation, recrystallisation, grain refinement and texture in an Al–1.2Mn alloy were investigated. Based on hardness and electrical conductivity measurements, a precipitation–recrystallisation diagram was generated, which described the sequence of recrystallisation and precipitation. The results showed that recrystallisation was significantly retarded during the annealing treatment for the cold-rolled alloys with a supersaturated solid solution or with dense pre-existing dispersoids. If precipitation occurred prior to recrystallisation, the precipitates caused a strong resistance to recrystallisation, resulting in a coarse and elongated grain structure with a dominant normal direction-rotated cube texture. In contrast, when recrystallisation was completed before precipitation, recrystallisation was little affected by the precipitates, leading to a fine-grained structure with a weak cube texture.
LiuK, ChenXG.Development of Al-Mn-Mg 3004 alloy for applications at elevated temperature via dispersoid strengthening. Mater Des. 2015;84:340–350. doi: 10.1016/j.matdes.2015.06.140
2.
LiYJ, ArnbergL.Evolution of eutectic intermetallic particles in DC-cast AA3003 alloy during heating and homogenization. Mater Sci Eng A. 2003;347:130–135. doi: 10.1016/S0921-5093(02)00555-5
3.
MuggerudAMF, MørtsellEA, LiY, Dispersoid strengthening in AA3xxx alloys with varying Mn and Si content during annealing at low temperatures. Mater Sci Eng A. 2013;567:21–28. doi: 10.1016/j.msea.2013.01.004
4.
DehmasM, WeisbeckerP, GeandierG, Experimental study of phase transformations in 3003 aluminium alloys during heating by in situ high energy X-ray synchrotron radiation. J Alloys Compd. 2005;400:116–124. doi: 10.1016/j.jallcom.2005.03.062
5.
HuangHW, OuBL.Evolution of precipitation during different homogenization treatments in a 3003 aluminum alloy. Mater Des. 2009;30:2685–2692. doi: 10.1016/j.matdes.2008.10.012
6.
LiYJ, ArnbergL.Quantitative study on the precipitation behavior of dispersoids in DC-cast AA3003 alloy during heating and homogenization. Acta Mater. 2003;51:3415–3428. doi: 10.1016/S1359-6454(03)00160-5
BirolY.Impact of homogenization on recrystallization of a supersaturated Al-Mn alloy. Scr Mater. 2009;60:5–8. doi: 10.1016/j.scriptamat.2008.07.047
9.
LiuQ, YaoZY, GodfreyA, Effect of particles on microstructural evolution during cold rolling of the aluminum alloy AA3104. J Alloys Compd. 2009;482:264–271. doi: 10.1016/j.jallcom.2009.03.183
10.
HuangHW, OuBL, TsaiCT.Effect of homogenization on recrystallization and precipitation behavior of 3003 aluminum alloy. Mater Trans. 2008;49:250–259. doi: 10.2320/matertrans.MRA2007615
11.
DehmasM, Aeby-GautierE, ArchambaultP, Interaction between eutectic intermetallic particles and dispersoids in the 3003 aluminum alloy during homogenization treatments. Metall Mater Trans A. 2013;44:1059–1073. doi: 10.1007/s11661-012-1473-1
12.
DuQ, PooleWJ, WellsMA, Microstructure evolution during homogenization of Al-Mn-Fe-Si alloys: modeling and experimental results. Acta Mater. 2013;61:4961–4973. doi: 10.1016/j.actamat.2013.04.050
13.
MikhaylovskayaAV, PortnoyVK, MochugovskiyAG, Effect of homogenisation treatment on precipitation, recrystallization and properties of Al – 3% Mg – TM alloys (TM = Mn, Cr, Zr). Mater Des. 2016;109:197–208. doi: 10.1016/j.matdes.2016.07.010
14.
PouraliakbarH, PakbazM, FiroozS, Study on the dynamic and static softening phenomena in Al–6Mg alloy during two-stage deformation through interrupted hot compression test. Measurement2016;77:50–53. doi: 10.1016/j.measurement.2015.08.033
15.
PouraliakbarH, FiroozS, JandaghiMR, Combined effect of heat treatment and rolling on pre-strained and SPDed aluminum sheet. Mater Sci Eng A. 2014;612:371–379. doi: 10.1016/j.msea.2014.06.044
16.
BirolY.Homogenization of a twin-roll cast thin Al-Mn strip. J Alloys Compd. 2009;471:122–127. doi: 10.1016/j.jallcom.2008.04.005
17.
LiuK, MaH, ChenXG.Enhanced elevated-temperature properties via Mo addition in Al-Mn-Mg 3004 alloy. J Alloys Compd. 2017;694:354–365. doi: 10.1016/j.jallcom.2016.10.005
18.
BirolY.Recrystallization of a supersaturated Al–Mn alloy. Scr Mater. 2008;59:611–614. doi: 10.1016/j.scriptamat.2008.05.016
19.
HuangK, LiYJ, MarthinsenK.Effect of heterogeneously distributed pre-existing dispersoids on the recrystallization behavior of a cold-rolled Al-Mn-Fe-Si alloy. Mater Charact. 2015;102:92–97. doi: 10.1016/j.matchar.2015.02.015
20.
SomerdayM, HumphreysFJ.Recrystallisation behaviour of supersaturated Al-Mn alloys part 1 – Al-1.3 wt-%Mn. Mater Sci Technol. 2003;19:20–29. doi: 10.1179/026708303225008590
21.
LiuWC, MorrisJG.Evolution of recrystallization and recrystallization texture in continuous-cast AA 3015 aluminum alloy. Metall Mater Trans A. 2005;36:2829–2848. doi: 10.1007/s11661-005-0279-9
22.
ZhangYH, JensenDJ, ZhangYB, Three-dimensional investigation of recrystallization nucleation in a particle-containing Al alloy. Scr Mater. 2012;67:320–323. doi: 10.1016/j.scriptamat.2012.05.006
23.
KarlíkM, MánikT, LauschmannH.Influence of Si and Fe on the distribution of intermetallic compounds in twin-roll cast Al-Mn-Zr alloys. J Alloys Compd. 2012;515:108–113. doi: 10.1016/j.jallcom.2011.11.101
24.
SunN, PattersonBR, SuniJP, Microstructural evolution in twin roll cast AA3105 during homogenization. Mater Sci Eng A. 2006;416:232–239. doi: 10.1016/j.msea.2005.10.018
25.
JandaghiMR, PouraliakbarH, KhalajG, Study on the post-rolling direction of severely plastic deformed aluminum-manganese-silicon alloy. Arch Civ Mech Eng. 2016;16:876–887. doi: 10.1016/j.acme.2016.06.005
26.
PouraliakbarH, JandaghiMR, KhalajG.Constrained groove pressing and subsequent annealing of Al-Mn-Si alloy: microstructure evolutions, crystallographic transformations, mechanical properties, electrical conductivity and corrosion resistance. Mater Des. 2017;124:34–46. doi: 10.1016/j.matdes.2017.03.053
27.
PouraliakbarH, JandaghiMR, BaygiSJM, Microanalysis of crystallographic characteristics and structural transformations in SPDed Al-Mn-Si alloy by dual-straining. J Alloys Compd. 2017;696:1189–1198. doi: 10.1016/j.jallcom.2016.12.086
28.
EnglerO, KongXW.Recrystallisation textures of particle-containing Al-Cu and Al-Mn single crystals. Acta Mater. 2001;49:1701–1715. doi: 10.1016/S1359-6454(01)00087-8
29.
TangenS, SjølstadK, FuruT, Effect of concurrent precipitation on recrystallization and evolution of the P-texture component in a commercial Al-Mn alloy. Metall Mater Trans A. 2010;41:2970–2983. doi: 10.1007/s11661-010-0265-8
30.
HuangK, WangN, LiYJ, The influence of microchemistry on the softening behavior of two cold-rolled Al-Mn-Fe-Si alloys. Mater Sci Eng A. 2014;601:86–96. doi: 10.1016/j.msea.2014.02.037
31.
JandaghiMR, PouraliakbarH.Study on the effect of post-annealing on the microstructural evolutions and mechanical properties of rolled CGPed aluminum-manganese-silicon alloy. Mater Sci Eng A. 2017;679:493–503. doi: 10.1016/j.msea.2016.10.054
