Cold-rolled 6061 aluminium alloys are used to prepare semisolid billets by recrystallisation and partial melting. The effects of isothermal treatment parameters on the microstructures were investigated. The results indicated that the high isothermal holding temperature increases the experimental liquid fraction, average grain size and shape factor. A long isothermal holding time also increases the experimental liquid fraction and improves the spheroidisation degree of solid grains, but the average grain size also increases. Moreover, when the isothermal holding time at high temperature is increased, the size of intragranular liquid droplets increases, but their quantity decreases. The optimal isothermal holding temperature and time during semisolid isothermal treatment were 635°C and 5 – 10 min, respectively.
ChenTJ, MaY, LiYD, Microstructural evolution of equal channel angular pressed AZ91D magnesium alloy during partial remelting. Mater Sci Technol. 2010;26(10):1197–1206. doi: 10.1179/174328409X428873
2.
MurakamiY, MiwaK, KitoM, Fluidity evaluation of the AC4CH (A356) aluminum alloy semisolid slurry made by mechanical vibration method. Mater Trans. 2016;57:168–173. doi: 10.2320/matertrans.F-M2015838
3.
WangY, ZhaoS, ZhangC.Grain refinement of aluminum alloy bar by a modified rap process for semisolid forming. Mater Trans. 2017;58(02):176–181. doi: 10.2320/matertrans.M2016271
4.
QiMF, KangYL, YanY, Comparison of microstructure and mechanical properties of AZ91D alloy formed by rheomolding and high-pressure die casting. J Mater Eng Perform. 2015;24:1–15. doi: 10.1007/s11665-014-1279-y
5.
ChoiY, ParkJH.Control of surface temperature of an aluminum alloy billet by air flow during a heating process at elevated temperature. J Mech Sci Technol.2016;30(6):2753–2758. doi: 10.1007/s12206-016-0537-3
6.
ChenTJ, HuangLK, HuangXF, Effects of reheating temperature and time on microstructure and tensile properties of thixoforged AZ63 magnesium alloy. Mater Sci Technol. 2014;30(1):96–108. doi: 10.1179/1743284713Y.0000000317
7.
JangCH, JinCK, BolouriA, Effect of forming conditions on mechanical properties of rheoformed thin plates with microchannels using electromagnetic stirring. Proc Inst Mech Eng B J Eng Manuf. 2014;228(3):399–412. doi: 10.1177/0954405413496403
8.
GaoQ, YangB, MeiH, Microstructure and wear resistance of semisolid TiB/7050 composites produced by serpentine tube pouring technique. Mater Manuf Process. 2016;31(8):1029–1036. doi: 10.1080/10426914.2015.1037917
9.
DasP, SamantaSK, ChattopadhyayH, Eulerian two-phase flow simulation and experimental validation of semisolid slurry generation process using cooling slope. Mater Sci Technol. 2013;29(1):83–92. doi: 10.1179/1743284712Y.0000000075
10.
NayyeriMJ, HaghshenasDF.Evaluation of microstructural evolution of Mg–4Al–RE in SIMA process based on statistical approach. Mater Sci Technol. 2014;30(3):348–354. doi: 10.1179/1743284713Y.0000000373
11.
AhmadAH, NaherS, BrabazonD.The effect of direct thermal method, temperature and time on microstructure of a cast aluminum alloy. Mater Manuf Process. 2014;29(2):134–139. doi: 10.1080/10426914.2013.822980
12.
AtkinsonHV, LiuD.Microstructural coarsening of semisolid aluminium alloys. Mater Sci Eng A. 2008;496(1–2):439–446. doi: 10.1016/j.msea.2008.06.013
13.
ChenQ, ZhaoZD, ChenG, Effect of accumulative plastic deformation on generation of spheroidal structure, thixoformability and mechanical properties of large-size AM60 magnesium alloy. J Alloys Compd. 2015;632:190–200. doi: 10.1016/j.jallcom.2015.01.185
14.
WangN, ZhouZM, LuGM.Microstructural evolution of 6061 alloy during isothermal heat treatment. J Mater Sci Technol. 2011;27(1):8–14. doi: 10.1016/S1005-0302(11)60018-2
15.
JiangJF, WangY, AtkinsonHV.Microstructural coarsening of 7005 aluminum alloy semisolid billets with high solid fraction. Mater Charact. 2014;90:52–61. doi: 10.1016/j.matchar.2014.01.017
16.
XuY, HuL, JiaJ, Microstructure evolution of a SIMA processed AZ91D magnesium alloy based on repetitive upsetting-extrusion (RUE) process. Mater Charact. 2016;118:309–323. doi: 10.1016/j.matchar.2016.06.011
17.
KazemiA, NourouziS, KolahdoozA, Experimental investigation of thixoforging process on microstructure and mechanical properties of the centrifugal pump flange. J Mech Sci Technol. 2015;29(7):2957–2965. doi: 10.1007/s12206-015-0626-8
18.
ZhaoZD, ChenQ, TangZJ, Microstructural evolution and tensile mechanical properties of AM60B magnesium alloy prepared by the SIMA route. J Alloys Compd. 2010;497(1-2):402–411. doi: 10.1016/j.jallcom.2010.03.088
19.
BineshB, Aghaie-KhafriM.Phase evolution and mechanical behavior of the semisolid SIMA processed 7075 aluminum alloy. Metals. 2016;6(3):42–64. doi: 10.3390/met6030042
20.
ZhangL, LiuYB, CaoZY, Effects of isothermal process parameters on the microstructure of semisolid AZ91D alloy produced by SIMA. J Mater Process Technol. 2009;209(2):792–797. doi: 10.1016/j.jmatprotec.2008.02.046
21.
JiangJ, WangY, XiaoG, Comparison of microstructural evolution of 7075 aluminum alloy fabricated by SIMA and RAP. J Mater Process Technol. 2016;238:361–372. doi: 10.1016/j.jmatprotec.2016.06.020
22.
NayyeriMJ, DehghaniK.Microstructure evolution in as-cast and SIMA-processed AE42 magnesium alloy. J Mater Eng Perform. 2014;23(9):3077–3084. doi: 10.1007/s11665-014-1080-y
23.
HaghdadiN, Zarei-HanzakiA, Heshmati-ManeshS, The semisolid microstructural evolution of a severely deformed A356 aluminum alloy. Mater Des. 2013;49:878–887. doi: 10.1016/j.matdes.2013.02.051
