ASTM F75 femoral knee implant components distort during manufacture due to residual stress re-distribution or inducement. X-ray diffraction, neutron diffraction, centre-hole drilling and the contour method residual stress determination techniques were applied to as-cast and/or shot-blasted components. The centre-hole drilling and contour methods can only be considered qualitative as a result of uncertainty associated with the elastic anisotropy of gauge volumes. Additionally, neutron diffraction experimentation returned unfeasible results. However, it was qualitatively identified that a shot-blasting shell-removal process has the ability to significantly alter the bulk residual stress state of the implants and induce a stress state which would cause distortion by re-distribution following material removal during manufacturing processes.
HutchingsMT, WithersPJ, HoldenTM, Introduction to the characterization of residual stress by neutron diffraction. Boca Raton, FL: CRC Press; 2005.
5.
PrimeMB. Cross-sectional mapping of residual stresses by measuring the surface contour after a cut. J Eng Mater Technol. 2001;123(2):162–168. doi: 10.1115/1.1345526
6.
PrimeMB, DeWaldAT. The contour method. In: SchajerGS, editor. Practical residual stress measurement methods.
Chichester: Wiley; 2013. p. 109–138.
7.
JohnsonG. Residual stress measurements using the contour method. In: School of materials.
Manchester: University of Manchester; 2008.
8.
HosseinzadehF, KowalJ, BouchardPJ. Towards good practice guidelines for the contour method of residual stress measurement. J Eng. 2014; 16 pp. DOI:10.1049/joe.2014.0134
9.
CullityBD, StockSR. Elements of X-ray diffraction.
New Jersey: Pearson Education Limited; 2014.
10.
BSI. BS EN 15305: Non-destructive testing. Test method for residual stress analysis by X-ray diffraction. London: BSI; 2008.
11.
ASTM E837. ASTM E837: Standard method for determining residual stresses by the hole drilling strain gauge method.
West Conshohocken, PA: ASTM International; 2013.
12.
GrantPV, LordJD, WhiteheadPS. Measurement of residual stresses by the incremental hole drilling technique, in Measurement good practice guide No. 53 – Issue 2.
London: NPL; 2006.
13.
Vishay Precision Group. Measurement of residual stresses by the hole-drilling strain gauge method – Technical note TN-503. 2010. [cited 2015 July 7]. Available from: http://www.vishaypg.com/docs/11053/tn503.pdf
14.
KaiserR. Study of the effect of casting variables and heat treatment procedures on the microstructure and mechanical properties of Co-Cr-Mo biomedical alloy. In: School of mechanical and materials engineering. Dublin: University College Dublin; 2013. p. 194.
15.
GiacchiJV, MorandoCN, FornaroO, Microstructural characterization of as-cast biocompatible Co-Cr-Mo alloys. Mater Charact. 2011;62(1):53–61. doi: 10.1016/j.matchar.2010.10.011
16.
GómezM, ManchaH, SalinasA, Relationship between microstructure and ductility of investment cast ASTM F-75 implant alloy. J Biomed Mater Res. 1997;34(2):157–163. doi: 10.1002/(SICI)1097-4636(199702)34:2<157::AID-JBM3>3.0.CO;2-P
17.
LiaoY, PourzalR, StemmerP, New insights into hard phases of CoCrMo metal-on-metal hip replacements. J Mech Behav Biomed. 2012;12:39–49. doi: 10.1016/j.jmbbm.2012.03.013
18.
GhazvinizadehH, MeratianM, KermanpurA, Effect of mould preheating on the microstructure of the investment cast ASTM F-75 implant alloy. Int J Eng. 2011;24(1):49–53.
19.
LewisRW, SeetharamuKN, HassanAY. Residual stress formation during casting. In: TottenG, HowesM, InoueT, editors. Handbook of residual stress and deformation of steel. OH: ASM International; 2002. p. 361–371.
20.
NorouziS, ShamsA, FarhangiH, The temperature range in the simulation of residual stress and hot tearing during investment casting. World Acad Sci Eng Technol. 2009;58:283–289.
21.
LiuBC, KangJW, XiongSM. A study on the numerical simulation of thermal stress during the solidification of shaped castings. Sci Technol Adv Mater. 2001;2:157–164. doi: 10.1016/S1468-6996(01)00041-9
22.
FarhangiH, NorouziS, Nili-AhmadabadiM. Effects of casting process variables on the residual stress in Ni-base superalloys. J Mater Process Technol. 2004;153-154:209–212. doi: 10.1016/j.jmatprotec.2004.04.199
23.
AfazovSM, BeckerAA, HydeTH. FE prediction of residual stresses of investment casting in a bottom core vane under equiaxed cooling. J Manuf Process. 2011;13:30–40. doi: 10.1016/j.jmapro.2010.10.001
24.
NorouziS, FarhangiH. The impact of ceramic shell strength on hot tearing during investment casting. International Conference on Advances in Materials and Processing Technologies (AMPT2010). Paris, France: American Institute of Physics; 2010.
25.
SadrossadatMS, JohanssonS. The effect of casting parameters on residual stresses and microstructure variations of an Al-Si cast alloy. Denver X-ray Conference. CO: ICDD; 2008.
26.
KirkD. Shot peening. Aircraft Eng Aerosp Technol. 1999;71(4):349–361. doi: 10.1108/00022669910270727
KaiserR, WilliamsonK, O'BrienC, The influence of cooling conditions on grain size, secondary phase precipitates and mechanical properties of biomedical alloy specimens produced by investment casting. J Mech Behav Biomed Mater. 2013;24:53–63. doi: 10.1016/j.jmbbm.2013.04.013
30.
HaukV. Structural and residual stress analysis by nondestructive methods. Amsterdam, The Netherlands: Elsevier; 1997.
31.
ISO. ISO/TS 21432: Non-destructive testing – standard test method for determining residual stresses by neutron diffraction. Geneva: ISO; 2005.
32.
OhmsC. Residual stresses in thick bi-metallic fusion welds: a neutron diffraction study.
Delft, The Netherlands: Delft University of Technology; 2013.
33.
HoldenTM, TraoreY, JamesJ, Determination and mitigation of the uncertainty of neutron diffraction measurements of residual strain in large-grained polycrystalline material. J Appl Crystallogr. 2015;48(2):582–584. doi: 10.1107/S1600576715002757
34.
RobinsonJS, HughesDF, TrumanCE. Confirmation of principal residual stress directions in rectilinear components by neutron diffraction. Strain. 2010;47(2):36–42.
35.
JamesJA, SantistebanJR, EdwardsL, A virtual laboratory for neutron and synchrotron strain scanning. Phys B Condens Matter. 2004;350:E743–E746. doi: 10.1016/j.physb.2004.03.194
GangulyS, JamesJA, FitzpatrickME, Automation of a neutron diffractometer for analysis of residual stress inside complex engineering components. Appl Phys A. 2010;99(3):601–606. doi: 10.1007/s00339-010-5615-2
38.
Von DreeleRB, JorgensenJD, WindsorCG. Rietveld refinement with spallation neutron powder diffraction data. J Appl Crystallogr. 1982;15:581–589. doi: 10.1107/S0021889882012722
39.
LarsonAC, Von DreeleRB. General Structure Analysis System (GSAS). Los Alamos National Laboratory Report LAUR 86-748, 2004.
40.
KerrM, PrimeMB, SwensonH, Residual stress characterization in a dissimilar metal weld nuclear reactor piping system mock up. J Press Vess Technol. 2013;135(4):1–8. doi: 10.1115/1.4024446
41.
HosseinzadehF, LedgardP, BouchardPJ. Controlling the cut in contour residual stress measurements of electron beam welded Ti-6Al-4V alloy plates. Exp Mech. 2013;53(5):829–839. doi: 10.1007/s11340-012-9686-1
42.
BouchardPJ, LedgardP, HillerS, HosseinzadhT. Making the cut for the contour method. In: Silva GomesJF, VazMAP, editors. 15th International Conference on Experimental Mechanics. Portugal: Porto; 2012.
43.
PrimeMB, SebringRJ, EdwardsJM, Laser surface-contouring and spline data-smoothing for residual stress measurement. Exp Mech. 2004;44(2):176–184. doi: 10.1007/BF02428177
44.
RobinsonJS, RedingtonW. The influence of alloy composition on residual stresses in heat treated aluminium alloys. Mater Charact. 2015;105:47–55. doi: 10.1016/j.matchar.2015.04.017
45.
SasakiT, KobayashiY. X-ray multiaxial stress analysis using two debye rings. Denver X-ray Conference. CO: ICDD; 2008.
46.
Vishay Precision Group. Milling guide for residual stress measurements RS-200. 2011. [cited 2016 June 7]. Available from: http://www.vishaypg.com/doc?11304
47.
Vishay Precision Group. The three-wire quarter-bridge circuit-Technical Tip TT-612. 2015. [cited 2016 May 30]. Available from: http://www.vishaypg.com/doc?11092
48.
SchajerGS, WhiteheadPS. Hole drilling and ring coring. In: SchajerGS, editor. Practical residual stress measurement methods.
Chichester: John Wiley and Sons; 2013. p. 29–64.
49.
Vishay Precision Group. Surface preparation for strain gage bonding-Instruction bulletin B-129. 2014. [cited 2016 May 30]. Available from: http://www.vishaypg.com/doc?11129
50.
Vishay Precision Group. Strain gage application with M-Bond AE-10, AE-15 and GA-2 adhesive systems-Instruction bulletin B-137. 2014. [cited 2016 May 30]. Available from: http://www.vishaypg.com/doc?11137
51.
PreveyPS. Residual-stress distributions produced by strain-gage surface preparation. Exp Mech. 1988;28(1):92–97. doi: 10.1007/BF02329002
52.
SerraY, FicquetX, KingstonEJ. Residual stress measurement using the hole drilling technique on components outside the ASTM E837 standard. Adv Mater Res. 2014;996:301–306. doi: 10.4028/www.scientific.net/AMR.996.301
53.
KaiserR, WilliamsonK, O'BrienC, Effects of section size, surface cooling conditions and crucible material on microstructure and as-cast properties of investment cast Co-Cr biomedical alloy. Metall Mater Trans A. 2013;44(12):5333–5342. doi: 10.1007/s11661-013-1825-5
ISO. ISO 14577-1 Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 1: Test method. Geneva: ISO; 2015.
56.
ASTM. ASTM E2546: Standard practice for instrumented indentation testing.
West Conshohocken, PA: ASTM International; 2015.
57.
SchwartzAJ, KumarM, AdamsBL, FieldDP. Electron backscatter diffraction in materials science. 2nd ed. New York: Springer; 2009.
58.
FarhangiH, NorouziS, Nili-AhmadabadiM. Effects of casting process variables on the residual stress in Ni-base superalloys. J Mater Process Technol. 2004;153-154:209–212. doi: 10.1016/j.jmatprotec.2004.04.199
59.
VangiD, TelliniS. Hole-drilling strain-gauge method: residual stress measurement with plasticity effects. J Eng Mater Technol. 2010;132:1–7. doi: 10.1115/1.3184030
60.
KentaY, ManamiM, AkihikoC. Mechanical properties of as-forged Ni-free Co-29Cr-6Mo alloys with ultrafine-grained microstructure. Mater Sci Eng A. 2011;528(18):5961–5966. doi: 10.1016/j.msea.2011.04.027
61.
SteinzigM, UpshawD, RatsyJ. Influence of drilling parameters on the accuracy of hole-drilling residual stress measurements. Exp Mech. 2014;54(99):1537–1543. doi: 10.1007/s11340-014-9923-x
62.
NauA, ScholtesB. Evaluation of the high-speed drilling technique for the incremental hole-drilling method. Exp Mech. 2013;53:531–542. doi: 10.1007/s11340-012-9641-1
StefanescuDM. Science and engineering of casting solidification.
New York: Springer; 2009.
66.
FazalL, WeiL, Da FonsecaJQ. Grain deformation in a cast Ni superalloy: comparing experimental and modelling results. BSSM Young Stress Analyst Competition 2016, 2016.
67.
JosicL, SteuwarA, LehmannE. Energy selective neutron radiography in material research. Appl Phys A. 2010;99(3):515–522. doi: 10.1007/s00339-010-5602-7
68.
SantistebanJR, EdwardsL, StelmukhV. Characterization of textured materials by TOF transmission. Phys B Condens Matter. 2006;385–386(Part 1):636–638. doi: 10.1016/j.physb.2006.06.090
69.
BoinM, HilgerA, KardjilovN, Validation of Bragg edge experiments by Monte Carlo simulations for quantitative texture analysis. J Appl Crystallogr. 2011;44:1040–1046. doi: 10.1107/S0021889811025970
70.
EigenmannB, MacherauchE. Röntgenographische Untersuchung von Spannungszuständen in Werkstoffen. Teil III. Fortsetzung von Matwiss. und Werkstofftechn. Heft 3/1995, S. 148–160 und Heft 4/1995, S. 199–216. Materwiss Werksttech. 1996;27(9):426–437. doi: 10.1002/mawe.19960270907
