This paper investigated the influence of electric pulses on the microstructure evolution and mechanical property of hot-stamping process of DP1180. The thickness distribution and absorbed energy of the forming parts were also calculated. The results showed that dynamic recrystallisation occurs in the middle zone in the current auxiliary tension. Moreover, the current would bypass the microcrack. The current auxiliary hot-stamping can be carried out with a current density of 9.7–10.4 A mm−2, thickness distribution formed at 10.4 A mm−2 has the lowest fluctuation of thickness with thinnest rate of 18.7% in middle. The tensile-strength decreased with increasing the current density from 9.7 to 10.4 A mm−2 while elongation increased and the absorbed energy can reached 28.39 kJ at current density of 10.0 A mm−2.
NeugebauerR., AltanT., GeigerM., KleinerM. and SterzingA.: ‘Sheet metal forming at elevated temperatures’, CIRP Ann. Manuf. Technol., 2006, 55, 793–816. doi: 10.1016/j.cirp.2006.10.008
2.
KuziakR., KawallaR. and WaenglerS.: ‘Advanced high strength steels for automotive industry’, Arch. Civ. Mech. Eng., 2008, 8, 103–117. doi: 10.1016/S1644-9665(12)60197-6
3.
CuiJ., SunG., XuJ., HuangX. and LiG.: ‘A method to evaluate the formability of high-strength steel in hot stamping’, Mater. Des., 2015, 77, 95–109. doi: 10.1016/j.matdes.2015.04.009
4.
KomgritL., HamasakiH., HinoR. and YoshidaF.: ‘Elimination of springback of high-strength steel sheet by using additional bending with counter punch’, J. Mater. Process. Technol., 2016, 229, 199–206. doi: 10.1016/j.jmatprotec.2015.08.029
5.
AbeY., OhmiT., MoriK. and MasudaT.: ‘Improvement of formability in deep drawing of ultra-high strength steel sheets by coating of die’, J. Mater. Process. Technol., 2014, 214, (9), 1838–1843. doi: 10.1016/j.jmatprotec.2014.03.023
6.
MoriK., MakiS. and TanakaY.: ‘Warm and hot stamping of ultra high tensile strength steel sheets using resistance heating’, CIRP Ann. Manuf. Technol., 2005, 54, (07), 209–212. doi: 10.1016/S0007-8506(07)60085-7
7.
YanagimotoJ., OyamadaK. and NakagawaT.: ‘Springback of high-strength steel after hot and warm sheet formings’, CIRP Ann. Manuf. Technol., 2005, 54, (1), 213–216. doi: 10.1016/S0007-8506(07)60086-9
8.
TroitskiiO. A. and LikhtmanV. I.: The Anisotropy of the Action of Electron and gamma Radiation on the Deformation of Zinc Single Crystals in the Brittle State, 196391, 1963.
9.
TroitskiiO. A.: ‘Effect of the electron state of a metal on its mechanical properties and the phenomenon of electroplasticity’, Phys. Met. Metallogr., 1977, 9, 38–46.
10.
OkazakiK., KagawaM. and ConradH.: ‘A study of the electroplastic effect in metals’, Scr. Metall., 1978, 12, 1063–1068. doi: 10.1016/0036-9748(78)90026-1
11.
ConradH. and YangD.: ‘Effect of an electric field on the plastic deformation kinetics of electrodeposited Cu at low and intermediate temperatures’, Acta Mater., 2002, 50, 2851–2866. doi: 10.1016/S1359-6454(02)00109-X
12.
LiuJ. Y. and ZhangK. F.: ‘Resistance heating superplastic forming and influence of current on deformation mechanism of TA15 titanium alloy’, Int. J. Adv. Manuf. Technol., 2015, 76, 1673–1680. doi: 10.1007/s00170-014-6286-5
13.
LiC., JiangS. S. and ZhangK. F.: ‘Pulse current-assisted hot-forming of light metal alloy’, Int. J. Adv. Manuf. Technol., 2012, 63, 931–938. doi: 10.1007/s00170-012-3934-5
14.
LiC., ZhangK. F., JiangS. S. and ZhaoZ. P.: ‘Pulse current auxiliary bulging and deformation mechanism of AZ31 magnesium alloy’, Mater. Des., 2012, 34, 170–178. doi: 10.1016/j.matdes.2011.08.007
15.
MoriK., SaitoS. and MakiS.: ‘Warm and hot punching of ultra high strength steel sheet’, CIRP Ann. Manuf. Technol., 2008, 57, 321–324. doi: 10.1016/j.cirp.2008.03.125
16.
XieH., WangQ., LiuK., PengF., DongX. and WangJ.: ‘Investigation of influence of direct-current pulses on springback during V-bending of AZ31B magnesium alloy sheet’, J. Mater. Process. Technol., 2015, 219, 321–327. doi: 10.1016/j.jmatprotec.2014.12.011
17.
GuanL., TangG. and ChuP. K.: ‘Recent advances and challenges in electroplastic manufacturing processing of metals’, J. Mater. Res., 2010, 25, (7), 1215–1224. doi: 10.1557/JMR.2010.0170
18.
OkazakiK., KagawaM. and ConradH.: ‘An evaluation of the contributions of skin, pinch and heating effects to the electroplastic effect in titatnium’, Mater. Sci. Eng., 1980, 45, (2), 109–116. doi: 10.1016/0025-5416(80)90216-5
19.
YanagimotoJ. and IzumiR.: ‘Continuous electric resistance heating—Hot forming system for high-alloy metals with poor workability’, J. Mater. Process. Technol., 2009, 209, (6), 3060–3068. doi: 10.1016/j.jmatprotec.2008.07.010
20.
LiuK., DongX. H., XieH. Y. and PengF.: ‘Effect of pulsed current on the deformation behavior of AZ31B magnesium alloy’, Mater. Sci. Eng. A, 2015, 623, 97–103. doi: 10.1016/j.msea.2014.11.039
21.
ZhouQ., QianL. H., ZhaoL. J., ZhuQ., MengJ. and ZhangF.: ‘Loading-rate dependence of fracture absorption energy of low-carbon carbide-free bainitic steel’, J. Alloys Compd., 2015, 650, 944–948. doi: 10.1016/j.jallcom.2015.06.215
22.
LvS., ChenS., MaoX., WangX., ZhuD. and HuoX.: ‘Study on recrystallization temperature of Ti microalloyed high strength steel in cold-rolled strips’, Iron Steel Vanadium Titanium, 2011, 32, 43–47.
23.
SarwarM. and PriestnerR.: ‘Influence of ferrite-martensite microstructural morphology on tensile properties of dual-phase steel’, J. Mater. Sci., 1996, 31, 2091–2095. doi: 10.1007/BF00356631
