Sintering shrinkage of prior cold compacted iron rings with different geometry (height to wall thickness ratio) and green density in the 6.5–7.3 g/cm3 range was investigated. It displays a minimum at an intermediate green density. Axial, tangential and radial shrinkages are different, due to the gradients of green density along the axial and the radial directions. Therefore, the effect of height on shrinkage and its anisotropy is the result of their effect on the stress distribution in the green parts during cold compaction, and the resulting green density and deformation experienced by the powder. Anisotropy decreases on increasing shrinkage.
CristofoliniI, PillaM, MolinariA, . DOE investigation of anisotropic dimensional change during sintering of iron-copper-carbon. Int J Powder Metall. 2012;48(4):37–43.
2.
CristofoliniI, PillaM, LarsonM, . A DOE analysis of dimensional change on sintering of a 3%Cr-0.5%Mo-x%C steel and its effect on dimensional and geometrical precision. Powder Metall Progr2012;3(12):127–143.
3.
CristofoliniI, CorsentinoN, PillaM, . Influence of geometry on the anisotropic dimensional change on sintering of PM parts. Adv Powder Metall Part Mater. 2013;11:49–61.
4.
CristofoliniI, CorsentinoN, LarssonM, . Study of the influence of material and geometry on the anisotropy of dimensional change on sintering of powder metallurgy parts. Int J Prec Eng Manuf. 2014;15(9):1865–1873. doi: 10.1007/s12541-014-0540-5
5.
CristofoliniI, CorsentinoN, MolinariA, . Influence of geometry and process variables on the anisotropy parameter K. Adv Powder Metall Part Mater2015;1:31–40.
6.
CristofoliniI, CorsentinoN, LarssonM, . Analytical model of the anisotropic dimensional change on sintering of ferrous PM parts. Powder Metall Progr. 2016;16(1):27–39. doi: 10.1515/pmp-2016-0003
7.
CristofoliniI, MenapaceC, CazzolliM, . The effect of anisotropic dimensional change on the precision of steel parts produced by powder metallurgy. J Mater Proc Technol. 2012;7(212):1513–1519. doi: 10.1016/j.jmatprotec.2012.02.009
8.
CristofoliniI, SelberF, MenapaceC, . Anisotropy of dimensional variation and its effect on precision of sintered parts. CD Proceedings EURO PM2012 Congress & Exhibition, Basel; 2012 September 16–19; ed. EPMA, Shrewsbury (UK);, 2012, 1. p. 519–524.
9.
CristofoliniI, CorsentinoN, MolinariA, . A design procedure accounting for the anisotropic dimensional change on sintering of ferrous PM parts. Adv Powder Metall Part Mater. 2014;1:115–127.
10.
CorsentinoN, CristofoliniI, LarssonM, . Anisotropy of the dimensional variation of sintered parts: a predictive model and a statistical evaluation of its reliability. CD Proceedings EuroPM2015 Congress & Exhibition, Reims (France); 2015 October 4–7; ed. Shrewsbury (UK): EPMA.
11.
OlevskyEA.Theory of sintering: from discrete to continuum. Mater Sci Eng R. 1998;23:41–100. doi: 10.1016/S0927-796X(98)00009-6
12.
WakaiF, ChiharaK, YoshidaM.Anisotropic shrinkage induced by particle rearrangement in sintering. Acta Mater. 2007;55:4553–4566. doi: 10.1016/j.actamat.2007.04.027
13.
WakaiF, ShinodaY.Anisotropic sintering stress for sintering of particles arranged in orthotropic symmetry. Acta Mater. 2009;57:3955–3964. doi: 10.1016/j.actamat.2009.04.049
14.
WakaiF, AkatsuT.Anistropic viscosities and shrinkage rate in sintering of particles arranged in simple orthorhombic structure. Acta Mater. 2010;58:1921–1929. doi: 10.1016/j.actamat.2009.11.035
ZavaliangosA, BouvardD.Numerical simulation of anisotropy in sintering due to prior compaction. Int J Powder Metall. 2000;36(7):59–65.
17.
ZavaliangosA, MissiaenJM, BouvardD.Anisotropy in shrinkage during sintering. Sci Sinter. 2006;38:13–25. doi: 10.2298/SOS0601013Z
18.
MolinariA, MenapaceC, TorresaniE, . Working hypothesis for origin of anisotropic sintering shrinkage caused by prior uniaxial cold compaction. Powder Metall. 2013;56(3):189–195. doi: 10.1179/1743290112Y.0000000043
19.
TorresaniE, CristofoliniI, MolinariA.Study of the anisotropic microstructure of uniaxially cold compacted green parts. Adv Powder Metall Part Mater2015;3:9–18.
20.
AmirabdollahianS, DeirminaF, MolinariA.Study of the pores characteristics in the uniaxially cold compacted green parts by Image Analysis. CD Proceedings World PM2016 Hamburg (Germany); 2016 October 9–13; ed. Shrewsbury (UK): EPMA.
21.
BaselliS, MolinariA.The geometrical model of sintering. CD Proceedings EuroPM2017 Congress & Exhibition, Milano (Italy); 2017 October 1–5; ed. Shrewsbury (UK): EPMA.
22.
TorresaniE, BaselliS, AmirabdollhaianS, . Effect of the green microstructure on the sintering shrinkage of metallic powders, to be submitted to Powd. Metall.
23.
MolinariA, TorresaniE, MenapaceC, . A study of sintering shrinkage kinetics of cold compacted ferrous green parts. Adv Powder Metall Part Mater2013;5:25–32.
24.
MolinariA, TorresaniE, MenapaceC, . The anisotropy of dimensional change on sintering of iron. J Am Ceram Soc. 2015;98(11):3431–3437. doi: 10.1111/jace.13852
25.
MolinariA, BisoffiE, MenapaceC, . Shrinkage kinetics during early stage sintering of cold isostatically compacted iron powder. Powder Metall. 2014;57(1):61–69. doi: 10.1179/1743290113Y.0000000068
