This study reports for the first time the synthesis of syntactic composite foams based on magnesium matrix and hollow fly ash cenosphere particles using the powder metallurgy technique involving hybrid microwave sintering. The effects of varying amounts of hollow cenosphere particle addition on the density, microstructure, thermomechanical and mechanical properties of pure magnesium were investigated. Density measurements indicated up to 18% reduction in density with the highest quantity of cenospheres (15%) addition to the magnesium. Microstructural examination demonstrated evenly distributed, intact and a few broken cenosphere particles with good interfacial integrity. Phase analysis showed finely distributed intermetallic phases such as MgO and Mg2Si due to the reaction between Mg matrix and the hollow cenosphere reinforcement. Mechanical property measurements showed retention/slight improvement in specific mechanical properties of magnesium due to hollow fly ash cenosphere particles. However, the tensile ductility was marginally affected.
RohatgiP. K., GuptaN., SchultzB. F., and LuongD. D.: ‘The synthesis, compressive properties, and applications of metal matrix syntactic foams’, JOM., 2011, 63, (2), 36–42.
7.
RajanT., PillaiR., PaiB., SatyanarayanaK., and RohatgiP.: ‘Fabrication and characterisation of Al–7Si–0.35 Mg/fly ash metal matrix composites processed by different stir casting routes’, Compos. Sci. Technol., 2007, 67, (15), 3369–3377. http://dx.doi.org/10.1016/j.compscitech.2007.03.028
8.
MondalD., DasS., RamakrishnanN., and BhaskerK. U.: ‘Cenosphere filled aluminum syntactic foam made through stir-casting technique’, Compos. Part A: Appl. Sci. Manuf., 2009, 40, (3), 279–288. doi: 10.1016/j.compositesa.2008.12.006
9.
GuptaN., LuongD. D., and ChoK.: ‘Magnesium matrix composite foams—density, mechanical properties, and applications’, Metals., 2012, 2, (3), 238–252. http://dx.doi.org/10.3390/met2030238
10.
AhmaruzzamanM.: ‘A review on the utilization of fly ash’, Prog. Energy Combust. Sci., 2010, 36, (3), 327–363. doi: 10.1016/j.pecs.2009.11.003
11.
ZhangZ., HanB. Q., WitkinD., AjdelsztajnL., and LavernaE. J.: ‘Synthesis of nanocrystalline aluminum matrix composites reinforced with in situ devitrified Al–Ni–La amorphous particles’, Scripta Mater., 2006, 54, (5), 869–874. http://dx.doi.org/10.1016/j.scriptamat.2005.11.003
12.
RohatgiP., DaoudA., SchultzB., and PuriT.: ‘Microstructure and mechanical behavior of die casting AZ91D-Fly ash cenosphere composites’, Compos. Part A: Appl. Sci. Manuf., 2009, 40, (6), 883–896. doi: 10.1016/j.compositesa.2009.04.014
13.
HuangZ. and YuS.: ‘Microstructure characterization on the formation of in situ Mg2Si and MgO reinforcements in AZ91D/Flyash composites’, J. Alloy. Compd., 2011, 509, (2), 311–315. http://dx.doi.org/10.1016/j.jallcom.2010.09.015
14.
HuangZ., YuS., LiuJ., and ZhuX.: ‘Microstructure and mechanical properties of in situ Mg2Si/AZ91D composites through incorporating fly ash cenospheres’, Mater. Design., 2011, 32, (10), 4714–4719. doi: 10.1016/j.matdes.2011.06.043
15.
LiuJ., YuS., HuangZ., MaG., and LiuY.: ‘Microstructure and compressive property of in situ Mg2Si reinforced Mg-microballoon composites’, J. Alloy. Compd., 2012, 537, 12–18. http://dx.doi.org/10.1016/j.jallcom.2012.05.027
16.
HartmannM., ReindelK., and SingerR.: ‘Fabrication and properties of syntactic magnesium foams’, MRS Proceedings, 1998, Cambridge University Press, 211.
17.
DaoudA., El-KhairM. A., Abdel-AzizM., and RohatgiP.: ‘Fabrication, microstructure and compressive behavior of ZC63 Mg–microballoon foam composites’, Compos. Sci. Technol., 2007, 67, (9), 1842–1853. doi: 10.1016/j.compscitech.2006.10.023
18.
KainerK. U. and MordikeB. L.: ‘Magnesium alloys and their applications’, 2000, Wiley-VCH, Weinheim, Wiley Online Library.
19.
GuptaM. and WongW.: ‘Enhancing overall mechanical performance of metallic materials using two-directional microwave assisted rapid sintering’, Scripta Mater., 2005, 52, (6), 479–483. http://dx.doi.org/10.1016/j.scriptamat.2004.11.006
20.
SeetharamanS., SubramanianJ., TunK. S., HamoudaA. S., and GuptaM.: ‘Synthesis and characterization of nano boron nitride reinforced magnesium composites produced by the microwave sintering method’, Materials., 2013, 6, (5), 1940–1955. doi: 10.3390/ma6051940
21.
ASTM E756-05: ‘Standard test method for measuring vibration-damping properties of materials’, 2005, West Conshohocken, PA, ASTM International.
22.
ASTM E384-11E1: ‘Standard test method for Knoop and Vickers hardness of materials’, 2007, West Conshohocken, PA, ASTM International.
23.
ASTM E9-09: ‘Standard test methods of compression testing of metallic materials at room temperature’, 2009, West Conshohocken, PA, ASTM International.
24.
ASTM E8/E8M-13a: ‘Standard test methods for tension testing of metallic materials’, 2013, West Conshohocken, PA, STM International.
25.
GuptaM., LeongW., and EugeneW.: ‘Microwave heating of metal-based materials’ in ‘Book: microwaves and materials’, 65–157; 2011, Singapore, John Wiley.
26.
GuoR. and RohatgiP.: ‘Chemical reactions between aluminum and fly ash during synthesis and reheating of Al-fly ash composite’, Metall. Mater. Trans. B., 1998, 29, (3), 519–525. http://dx.doi.org/10.1007/s11663-998-0086-y
27.
DieterG. E.: ‘Mechanical metallurgy’, 1976, New York, McGraw-Hill.
28.
CallisterW. D. and RethwischD. G.: ‘Materials science and engineering: an introduction’, 2007, New York, Wiley.
29.
NguyenQ. B., ChuaY. H. D., TunK. S., ChanJ., KwokR., WongW. L. E., and GuptaM.: ‘Effect of addition of nano-Al2O3 and copper particulates and heat treatment on the tensile response of AZ61 magnesium alloy’, J. Eng. Mater. Technol., 2013, 135, (3), 031004–031011. doi: 10.1115/1.4023769
