Reasons for using projects in higher education are briefly discussed and typical aims are outlined. The way projects are operated at Middlesex is described. A variety of student projects in the field of vehicle aerodynamics are illustrated. Projects such as car—caravan drag, roof-rack effects, the performance of go-karts and motor cycles are included. Brief details of the nature of, and results from, these projects are given. They are compared with contemporary reference material. Often despite the small scale of the tests they were surprisingly accurate. Difficulties with managing projects of this nature are outlined. Lessons are drawn from the way students pursued their projects, and tentative conclusions are made about the relevance of this type of project.
Get full access to this article
View all access options for this article.
References
1.
Van DeynseN., ‘Project work in the first years: A new method with specific objective’, European Journal of Engineering Education, 4, 199–204 (1980).
2.
BarkiH., ‘Design of a tow car spoiler’, Middlesex Polytechnic Diploma, project report (1976).
3.
FordP., ‘Drag reduction for a caravan using air deflectors’, Middlesex Polytechnic Diploma, project report (1976).
4.
WatersD. M.‘The aerodynamic behaviour of car—caravan combinations’, 1st Road Vehicle Aerodynamics Symposium, City University, paper 4 (1969).
5.
Report on deflector devices, Caravan Magazine, Feb. 1976.
6.
Road test report on caravan deflector, Hot Car Magazine, Dec. 1976.
7.
StockM., Private communication (1977).
8.
BuckleyF. T., and SekscienskiW. S., ‘Comparisons of effectiveness of commercially available devices for the reduction of aerodynamic drag on tractor-trailers’, SAE 750704 (1975).
9.
MetzL. D., and SensenbrennerK., ‘The influence of roughness elements on laminar to turbulent boundary layer transition as applied to scale model testing of automobiles’, SAE 730233 (1973).
10.
LarabeeE. E., ‘Small scale research in automobile aerodynamics’, SAE 660384 (1966).
11.
CooperK. R., ‘The wind tunnel simulation of surface vehicles’, J. Wind Engineering, 17, 167–198 (1984).
12.
CooperK. R., Contribution to discussion, Symposium on Aerodynamic Drag Mechanisms of Bluff Bodies and Road Vehicles, General Motor Research Labs, Sept. 27–28, (1976).
13.
HandsS. J., and ZdravkovichM. M., ‘Drag reduction for a passenger car towing a caravan’, J. Wind Eng., 9, 137–143 (1981).
14.
GotzH., ‘Examples of practical aerodynamics with passenger cars caravans and buses’, Conf. Proc. Designing with the Wind. Nantes, June 15–19, paper XI (1981).
15.
GarryK. P., ‘Wind tunnel investigation into the effectiveness of drag reducing devices for car caravan combinations’, Conf. Proc. Designing with the Wind, paper XI-1 (1981).
16.
JamesM., ‘An investigation into the feasibility of reducing the drag caused by the gap between railway coaches’, Middlesex Polytechnic Diploma in Mechanical Engineering, project report (1977).
17.
ModhaH., ‘Aerodynamic drag testing of motor vehicles whilst in motion’, Middlesex Polytechnic B.Sc. Engineering., project report (1981).
18.
KorstH. H., and WhiteR. A., ‘Evaluation of vehicle drag parameters from coastdown experiments conducted under non-ideal environmental conditions’, J. Fluids Engineering, ASME, 103, 133–141 (1981).
19.
WhiteR. G. S., ‘An experimental survey of vehicle aerodynamics characteristics' (2nd report), MIRA, 4 (1964).
20.
RoussillonG., ‘Contribution to accurate measurement of aerodynamic drag on a moving vehicle from coast down tests and determination of actual rolling resistances’, J. Wind Engineering and Industrial Aerodynamics, 9, 33–48 (1981).
21.
GinigalgodageK. K., ‘The use of air spoilers in aerodynamic drag reduction of car—caravan combinations’, B.Sc. (Hons) Mechanical Engineering, Middlesex Polytechnic, project report (1982).
22.
DaveS., ‘Effect of side skirting on aerodynamic lift force in a saloon car’, B.Sc. Mechanical Engineering, Middlesex Polytechnic, project report (1984).
23.
JanssenL. J.HuchoW. H., ‘The effect of various parameters on the aerodynamic drag of passenger cars’, Advances in Road Vehicle Aerodynamics, Cranfield, UK (1973).
24.
PallariaE., ‘An investigation into the reduction of drag on trucks using boundary layer suction’, B.Sc. (Hons) Mechanical Engineering, Middlesex Polytechnic, project report (1984).
25.
PauH. C., ‘Aerodynamic performance of aerofoils on the formula E racing go-karts’, B.Sc. (Hons) Mechanical Engineering, Middlesex Polytechnic, project report (1984).
26.
WoodwardS. P., ‘Improving the aerodynamic performance of the zip formula E racing kart, B.Eng. (Hons) Mechanical Engineering, Middlesex Polytechnic, project report (1986).
27.
WhiteA. S., and PauH. C., ‘The aerodynamic effectiveness of aerofoils on formula E, Karting, May, 42–43 (1985).
28.
PiskitzisY., ‘Aerodynamics of racing motorcycles’, BTEC HND in Mechanical & Production Engineering, Middlesex Polytechnic, project report (1986).
29.
Perreur-LloydK., ‘Coefficient of drag of a motorcycle’, BTEC HND in Mechanical & Production Engineering, Middlesex Polytechnic, project report (1987).
