This paper describes the procedure of electromagnetic and thermal modeling of an induction hardening load of 42CrMo4 steel. In addition to the temperature and field level dependent physical properties of the material, the magnetic behavior of the load is captured by means of some kind of non-linear impedance boundary condition which simplifies the computational cost of the simulation. The numerical results show the critical behavior around Curie temperature. Finally, a comparison between several simulation results and experimental measurements are provided to assess the usefulness of the proposed electro-thermal simulation.
RudnevV.LovelessD. and CookR., Handbook of Induction Heating, 2nd edn, CRC Press, 2017.
2.
LucíaO.MaussionP.DedeE.J. and BurdíoJ.M., Induction Heating technology and its applications: Past developments, current technology, and future challenges, IEEE Transactions on Industrial Electronics61 (2014), 2509–2520.
BarglikJ., Mathematical modeling of induction surface hardening, COMPEL: The International Journal for Computation and Mathematics in Electrical and Electronic Engineering1(35) (2016), 1403–1417, doi:10.1108/COMPEL-09-2015-0323.
5.
BocherP.MingardiD.LarregainB.BridierF.DughieroF. and SpezzapriaM., Simulation of fast induction surface heating and comparison with experimental full-field surface temperature measurements, International Conference on Heating by Electromagnetic Sources1 (2013), 99–108.
6.
BlinovK.NikanorovA.NackeB. and KlöpzigM., Numerical simulation and investigation of induction through-heaters in dynamic operation mode, COMPEL – The International Journal for Computation and Mathematics in Electrical and Electronic Engineering1(30) (2011), 1539–1549, doi:10.1108/03321641111152694.
7.
SchwenkM.HoffmeisterJ. and SchulzeV., Experimental determination of process parameters and material data for numerical modeling of induction hardening, Journal of Materials Engineering and Performance22 (2013), 1861–1870.
8.
PierceD.T.MuralidharanG.TrofimovA.TorresJ.WangH.HaynesJ.A., Evaluation of thermal processing and properties of 422 martensitic stainless steel for replacement of 4140 steel in diesel engine pistons, Materials and Design2 (2022), 214.
9.
AreitioaurtenaM.SegurajauregiU.AkujärviV.FiskM.UrrestiI. and UkarE., A semi-analytical coupled simulation approach for induction heating, Advanced Modeling and Simulation in Engineering Sciences8(1) (2021), doi:10.1186/s40323-021-00199-0.
10.
AkujärviV.CedellT.FrognerK. and AnderssonM., Mapping of magnetic properties for simulations of high-Temperature electromagnetic applications, COMPEL – The International Journal for Computation and Mathematics in Electrical and Electronic Engineering36 (2017), 546–554.
11.
CoupardD.Palin-lucT.BristielP.JiV. and DumasC., Residual stresses in surface induction hardening of steels: Comparison between experiment and simulation, Materials Science and Engineering A7(487) (2008), 328–339.
FiskM.RistinmaaM.HultkrantzA. and LindgrenL.E., Coupled electromagnetic-thermal solution strategy for induction heating of ferromagnetic materials, Applied Mathematical Modelling111 (2022), 818–835, doi:10.1016/j.apm.2022.07.009.
14.
FuX.WangB.TangX.JiH. and ZhuX., Study on induction heating of workpiece before gear rolling process with different coil structures, Applied Thermal Engineering114 (2017), 1–9, doi:10.1016/j.applthermaleng.2016.11.192.
15.
SongM.C. and MoonY.H., Coupled electromagnetic and thermal analysis of induction heating for the forging of marine crankshafts, Applied Thermal Engineering98 (2016), 98–109, doi:10.1016/j.applthermaleng.2015.11.129.
16.
CanovaA.DughieroF.FasoloF.ForzanM.FreschiF.GiacconeL., Simplified approach for 3-D nonlinear induction heating problems, IEEE Transactions on Magnetics45 (2009), 1855–1858.
17.
CanovaA.DughieroF.FasoloF.ForzanM.FreschiF.GiacconeL., Identification of equivalent material properties for 3-D numerical modeling of induction heating of ferromagnetic workpieces, IEEE Transactions on Magnetics45 (2009), 1851–1854.
