A common technique to prevent the propagation of fatigue cracks in bridge girders is to drill crack-stop holes at crack tips. Stress concentrations at the crack tips are reduced and fatigue life of the bridge is extended. The size of the crack-stop hole needed to prevent further crack growth is determined by using known material properties and relationships developed through experimentation. However, these equations often result in a crack-stop hole diameter larger than can be practically drilled; physical limitations force crack-stop holes to be undersized in the field. To improve effectiveness of undersized holes to that of full-sized holes, a method is needed to strengthen undersized crack-stop holes. This study investigated the potential of a technique to improve the fatigue life of undersized, crack-stop holes. It uses piezoelectric actuators operated at ultrasonic frequencies to convert electrical signals into mechanical work. The technique produced residual compressive stresses of the same order of magnitude as those produced by static cold expansion. A suite of finite element models was created to quantify and characterize the residual stresses surrounding the cold-expanded, undersized, crack-stop holes. Results were compared with analyses in the literature.
Get full access to this article
View all access options for this article.
References
1.
DomazetZ.Comparison of Fatigue Crack Retardation Methods. Engineering Failure Analysis, Vol. 3, No. 2, 1996, pp. 137–147.
2.
VulićN., JecićS., and GrubišićV.Validation of Crack Arrest Technique by Numerical Modeling. International Journal of Fatigue, Vol. 19, No. 4, 1997, pp. 283–291.
3.
Kim RoddisW. M., and ZhaoY.Finite-Element Analysis of Steel Bridge Distortion-Induced Fatigue. Journal of Bridge Engineering, Vol. 8, No. 5, 2003, pp. 259–266.
4.
ZhaoY., and Kim RoddisW. M.Fatigue Behavior and Retrofit Investigation of Distortion-Induced Web Gap Cracking. Journal of Bridge Engineering, Vol. 12, No. 6, 2007, pp. 737–745.
5.
HuY., ShieldC. K., and DexterR. J.Use of Adhesives to Retrofit Out-of-Plane Distortion at Connection Plates. In Transportation Research Record: Journal of the Transportation Research Board, No. CD 11-S (CD-ROM), Transportation Research Board of the National Academies, Washington, D.C., 2005, pp. 419–427.
6.
AmroucheA., GhfiriR., ImadA., and MesmacqueG.Fatigue Life Estimation After Crack Repair in 6005 A-T6 Aluminum Alloy Using the Cold Expansion Hole Technique. Fatigue and Fracture of Engineering Materials and Structures, Vol. 23, 2000, pp. 991–916.
7.
de MatosP. F. P., McEvilyA. J., MoreiraP. M. G. P., and de CastroP. M. S. T.Analysis of the Effect of Cold-Working of Rivet Holes on the Fatigue Life of an Aluminum Alloy. International Journal of Fatigue, Vol. 29, No. 3, 2007, pp. 575–586.
8.
ForguesS. A., BernardM., and Bui-QuocT.3-D Axisymmetric Numerical Analysis and Experimental Study of the Fastener Hole Coldworking Process. In Computer Methods and Experimental Measurements for Surface Treatments Effects (BrebbiaC. A., and AliabadiM. H., eds.), Engineering Sciences 2, Computational Mechanics Publications, Southampton, United Kingdom, 1993, pp. 61–70.
9.
HermanR., and OzdemirA. T.Effect of Expansion Techniques and Plate Thickness on Near-Hole Residual Stresses and Fatigue Life of Cold Expanded Holes. Journal of Material Science, Vol. 34, 1999, pp. 1243–1252.
10.
LandryM. A., ArmenH.Jr., and EidinoffH. L.Enhanced Stop-Drill Repair Procedure for Cracked Structures. Fatigue in Mechanically Fastened Composite and Metallic Joints, ASTM STP 927 (PotterJ. M., ed.), American Society for Testing and Materials, Philadelphia, Pa., 1986, pp. 190–220.
11.
PavierM. J., PoussardC. G. C., and SmithD. J.Effect of Residual Stress Around Cold Worked Holes on Fracture Under Superimposed Mechanical Load. Engineering Fracture Mechanics, Vol. 63, No. 6, 1999, pp. 751–773.
12.
ShinC. S., SongP. S., and WangC. M.Fatigue Damage Repair: A Comparison of Some Possible Methods. International Journal of Fatigue, Vol. 18, No. 8, 1996, pp. 535–546.
13.
ZhangY., FitzpatrickM. E., and EdwardsL.Analysis of the Residual Stress Around a Cold-Expanded Fastener Hole in a Finite Plate. Strain, Vol. 41, No. 2, 2005, pp. 59–70.
14.
BallD., and LowryD. R.Experimental Investigation on the Effects of Cold Expansion of Fastener Holes. Fatigue and Fracture of Engineering Materials and Structures, Vol. 21, No. 1, 1998, pp. 17–34.
15.
PoolsukS.Measurement of the Elastic-Plastic Boundary Around Cold-worked Fastener Holes. PhD dissertation. Michigan State University, East Lansing, 1977.
16.
ReemsnyderH. S.Fatigue Life Extension of Riveted Connections. ASCE Journal of the Structural Division, Vol. 101, No. 12, 1975, pp. 2591–2608.
17.
HuhnH., and ValtinatG.Bolted Connections with Hot Dipped Galvanized Steel Members with Punched Holes. Proc. ECCS/AISC Workshop, Connection in Steel Structures V: Innovative Steel Connections, Amsterdam, June 3–5, European Convention for Construction Steelwork and American Institute of Steel Construction, 2004.
18.
BrownJ. D., LubitzD. J., CekovY. C., FrankK. H., and KeatingP. B.Evaluation of Influence of Hole Making upon the Performance of Structural Steel Plates and Connections. CTR Technical Report 0–4624–1. Center for Transportation Research, Austin, Tex., 2007.
19.
StatnikovE. S.Physics and Mechanisms of Ultrasonic Impact Treatment. IIV Document XIII-2004-04. International Institute of Welding, Paris, 2004.
20.
PhillipsJ. L.Sleeve Cold Working Fastener Holes, Vol. 1. AFML-TR-74-10. Air Force Materials Laboratory, Wright-Patterson AFB, Ohio, 1974.
21.
LeonA.Benefits of Split Mandrel Coldworking. International Journal of Fatigue, Vol. 20, No. 1, 1998, pp. 1–8.
22.
BarsomJ. M., and RolfeS. T.Fracture and Fatigue Control in Structures: Application of Fracture Mechanics, 3rd ed. ASTM, West Conshohocken, Pa., 2006.
23.
CreagerM.The Elastic Stress Field Near the Tip of a Blunt Crack. M.S. thesis. Lehigh University, Bethlehem, Pa., 1966.
24.
PoussardC., PavierM. J., and SmithD. J.Analytical and Finite Element Predictions of Residual Stresses in Cold Worked Fastener Holes. Journal of Strain Analysis for Engineering Design, Vol. 30, No. 4, 1995, pp. 291–304.
25.
PoussardC. G. C., PavierM. J., and SmithD. J.Prediction of Residual Stresses in Cold Worked Fastener Holes Using the Finite Element Method. Proc. 2nd Biennial European Joint Conference on Engineering Systems Design and Analysis, American Society of Mechanical Engineers, New York, 1994, pp. 47–53.
26.
OzeltonM. W., and CoyleT. G.Fatigue Life Improvement by Cold Working Fastener Holes in 7050 Aluminum. In Fatigue in Mechanically Fastened Composite and Metallic Joints, ASTM STP 927 (PotterJ. M., ed.), ASTM, Philadelphia, Pa., 1986, pp. 53–71.
27.
BoyerH. E.Atlas of Stress Strain Curves.ASM International, Materials Park, Ohio, 1987.
28.
de MatosP. F. P., MoreiraP. M. G. P., CamanhoP. P., and de CastroP. M. S. T.Numerical Simulation of Cold Working of Rivet Holes. Finite Elements in Analysis and Design, Vol. 41, Nos. 9-10, 2005, pp. 989–1007.
