Operating Speed on Crest Vertical Curves with Limited Stopping Sight Distance

Abstract

Horizontal and vertical elements of a highway are designed based on an assumed design speed. This concept was developed in the 1930s as a mechanism for designing rural alignments to permit most drivers to operate uniformly at their desired speed. In 1938, AASHO recognized that drivers select a speed influenced by the roadway environment instead of an assumed design speed. Recent research suggests that design speed is no longer the speed adopted by the faster group of drivers but that it has become a value used to establish the sharpness of horizontal and vertical design elements. The objective of this study was to establish the relationship between design and operating speeds for crest vertical curves with limited sight distance. Geometric data and 3,500 paired speeds (speeds at control and crest sections) were collected at 36 sites in 3 states. The results indicated that both the 85th percentile and the mean operating speeds were well above the inferred design speeds of the crest vertical curves for the range of conditions studied and that the lower the design speed the larger the difference between the 85th percentile speed and the design speed. The mean reductions in speed between the control and crest sections tend to increase as available sight distance is decreased; however, the reduction in speed is less than that suggested by current AASHTO criteria.

Get full access to this article

View all access options for this article.

References

A Policy on Sight Distance for Highways. AASHO, Washington, D.C., 1940.

Fambro

D. B.

, Fitzpatrick

, and Koppa

R. J.

. NCHRP Report 400: Determination of Stopping Sight Distances. TRB, National Research Council, Washington, D.C., 1997.

Barnett

Safe Side Friction Factors and Super-Elevation Design. HRB Proc., Vol. 16, 1936, pp. 69–80.

McLean

An Alternative to the Design Speed Concept for Low Speed Alinement Design. In Transportation Research Record 702, TRB, National Research Council, Washington D.C., 1979, pp. 55–63.

Good

M. C.

Road Curve Geometry and Driver Behavior. ARRB Special Report No. 15. Australian Road Research Board, Victoria, Australia, 1978.

A Policy on Geometric Design of Highways and Streets. AASHTO, Washington, D.C., 1994.

A Policy on Geometric Design of Highways and Streets. AASHTO, Washington, D.C., 1990.

Rowan

N. J.

, and Keese

C. J.

. A Study of Factors Influencing Traffic Speed. Bulletin 341, HRB, National Research Council, Washington, D.C., 1962.

Oppenlander

J. C.

Variables Influencing Spot-Speed Characteristics—Review of the Literature. Special Report 89, HRB, National Research Council, Washington, D.C., 1966.

10.

Garber

N. J.

, and Gadiraju

. Factors Affecting Speed Variance and Its Influence on Accidents. In Transportation Research Record 1213, TRB, National Research Council, Washington, D.C., 1989, pp. 64–71.

11.

Lefeve

B. A.

Speed Characteristics on Vertical Curves. HRB Proc., Vol. 32, 1953, pp. 395–413.

12.

Krammes

R. A.

, Brackett

R. Q.

, Shaffer

M. A.

, Ottesen

J. L.

, Anderson

I. B.

, Fink

K. L.

, Collins

K. M.

, Pendleton

O. J.

, and Messer

C. J.

. Horizontal Alignment Design Consistency for Rural Two-Lane Highways. Research Report FHWA-RD-94-034. FHWA, U.S. Department of Transportation, 1994.

13.

Mclean

J. R.

Review of the Design Speed Concept. Australian Road Research, Vol. 8, No. 1, March 1978, pp. 3–16.

14.

McLean

J. R.

Speeds, Friction Factors, and Alignment Design Standards. In Australian Research Record 154, Australian Road Research Board, Victoria, 1988, pp. 48–57.

15.

Messer

C. J.

, Mounce

J. M.

, and Brackett

R. Q.

. Highway Geometric Design Consistency Related to Driver Expectancy, Vol. II. Research Report No. FHWA/RD-81/036. FHWA, U.S. Department of Transportation, 1981.