Modelling of Break-up and Coalescence in Bubbly Two-Phase Flows

Abstract

Numerical simulations of gas-liquid two-phase flow with high superficial velocity in a vertical pipe were conducted with the use of the commercial software package STAR-CD 3.27. The change in bubble size due to breakup and coalescence was modelled by the S_γ model. The applicability and performance of the S_γ model in modelling of gasliquid bubbly flow were studied. The sensitivity of the S_γ model to the distribution moment γ, and the drainage mode were investigated. The numerical results were compared with the experimental data of Hibiki et al., (2001). Good agreement was achieved for axial velocities and void fraction for all tested cases. It was found in this work that the S_γ model is capable of predicting with reasonable accuracy the bubble size and its distribution even in high void fraction. Except in the near wall region, the simulated bubble size and therefore the interfacial area density fit well with the experiment measurements. It was observed that the predicted bubble size and interfacial area density obtained from both the S₀ and S₂ models are more or less the same, indicating that the numerical results are independent of the distribution moment γ. It was further found that, the drainage mode greatly affects the bubble size: an increase in mobility of the bubble surface enhances the coalescence and leads to an over-prediction of the bubble size in the pipe centre. The bubble size increases with the increase of the gas phase superficial velocity while the variation of the interfacial area density is smaller as it is a combined function of the bubble size and local gas hold-up.

Keywords

Breakup Bubbly flow Coalescence Euler-Euler model

References

Becker

Sokolichin

and Eigenberger

, Gas-liquid flow in bubble columns and loop reactors: Part II. Comparison of detailed experiments and flow simulations, Chem. Eng. Sci., 49, 1994, 5747–5762.

Chesters

A. K.

, Local coalescence rates in emulsions: A model for collision and film thinning process when drop inertia dominates, BRITE Report I-31, 1988.

Darmana

Deen

N. G.

and Kuipers

J. A. M.

, Detailed modeling of hydrodynamics, mass transfer and chemical reactions in a bubble column using a discrete bubble model, Chem. Eng. Sci., 60, 2005, 3383–3404.

De Bruijn

R. A.

, Newtonian drop breakup in general laminar flows. Development of a computer code to predict drop sizes, BRITE Report I-15, 1987.

Grace

H. P.

, Dispersion phenomena in high viscosity immiscible fluid and application of static mixers as dispersion devices in such systems, Chem. Eng. Comm., 14, 1982, 225–277.

Hibiki

and Ishii

, One-group interfacial area transport of bubbly flow in vertical round tubes, Int. J. Heat Mass Transfer, 43, 2000, 2711–2726.

Hibiki

Ishii

and Xiao

, Axial interfacial area transport of vertical bubbly flows, Int. J Heat and Mass Transfer, 44, 2001, 1869–1888.

, Application of Population Balance to CFD Modelling of Bubbly Flow via the MUSIG model, AEA Technology, AEAT-1096, 1996.

, Modelling multiphase flow with an Eulerian approach”, von Karman Institute Lecture Series – Industrial Two-Phase Flow CFD, May 23–27, von Karman Institute, Belgium, 2005.

10.

and Rao

, Modelling of droplet breakup and coalescence in an oil-water pipeline”, 6^th International Conference on Multiphase Flow, ICMF 2007, Leipzig, Germany, 2007, STAR-CD Version 3.20, Methodology Manual, Chapter 13, CD-adapco, UK, 2007.

11.

Kim

Ishii

and Beus

S. G.

, One-group interfacial area transport in vertical bubbly flow, Int. J. Heat Mass Transfer, 41, 1998, 1103–1112.

12.

Yao

and Morel

, Volumetric interfacial area prediction in upward bubbly two-phase flow, Int. J. Heat Mass Transfer, 47, 2004, 307–328.

13.

Yeoh

G. H.

and Tu

J. Y.

, Modeling gas-liquid bubbly flows, 15^th Australasian Fluid Mechanics Conference. The University of Sydney, Sydney, Australia, 2004.