Bonded Fibre Reinforced Polymer Strengthening in a Real Fire

Abstract

FRP strengthening is critically dependent upon the bonding adhesive. The adhesive used is typically an ambient cure epoxy with a glass transition temperature as low as 60°C. This paper describes the performance of bonded FRP strengthening within real compartment fires (the Dalmarnock Fire Tests), one of which was allowed to grow past flashover. The aim of these real fire tests was to complement the laboratory-based fire tests on FRP strengthened members that are currently being undertaken at various research centres. In this study, externally bonded plate and near-surface-mounted FRP strengthening were applied to the ceiling of a concrete structure. The FRP was protected using either an intumescent coating or gypsum boards, alongside FRP that was left unprotected. The tests demonstrated the vulnerability of FRP strengthening during a real compartment fire. The glass transition temperature was rapidly exceeded in the bonding adhesive for all samples. The near-surface mounted strengthening and the gypsum board protected strengthening was in a visibly better condition after the fire.

Keywords

fire testing epoxy adhesive CFRP strengthening concrete intumescent gypsum board

Get full access to this article

View all access options for this article.

References

ACI 440.2R (2002). Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, American Concrete Institute.

ACI 440R-07 (2007). Report on Fiber-Reinforced Polymer (FRP) Reinforcement for Concrete Structures, American Concrete Institute.

Barnes

Fidell

(2006). “Performance in fire of small-scale CFRP strengthened concrete beams”, Journal of Composites for Construction, ASCE, Vol. 10, No. 6, pp. 503–508.

Bisby

L.A.

Green

M.F.

and Kodur

V.K.R.

(2005). “Response to fire of concrete structures that incorporate FRP”, Progress in Structural Engineering and Materials, Vol. 7, No. 3, pp. 136–149.

Blondtrock

Taerwe

Vandevelde

(2001). “Fire testing of concrete slabs strengthened with fibre composite laminates”, Proceedings of the FRPRCS-5, pp. 547–556, Thomas Telford, London.

Clarke

J.L.

(1996). Structural Design of Polymer Composites—Eurocomp Design Code and Handbook, E & FN Spon, London, UK.

Concrete Society (2004), Design Guidance for Strengthening Concrete Structures using Fibre Composite Materials, Technical Report 55, 2nd Edition, The Concrete Society, Camberley, UK.

Drysdale

(1998), An Introduction to Fire Dynamics, 2nd edition, Wiley.

ISO 834–1 (1999). Fire-Resistance Tests – Elements of Building Construction – Part 1: General Requirements, International Organisation for Standardisation, Switzerland.

10.

Kodur

V.K.R.

Bisby

L.A.

and Green

M.F.

(2007). “Preliminary guidance for the design of FRP-strengthened concrete members exposed to fire”, Journal of Fire Protection Engineering, Vol. 17, No. 5, pp. 5–26.

11.

Liang

Welch

Stratford

and Kinsella

E.V.

(2007), “Development and validation of a generalised engineering methodology for thermal analysis of structural members in fire”, Proceedings of the Fire and Explosion Hazards 5, Edinburgh, UK, April.

12.

Porter

M.L.

and Harries

(2007). “Future directions for research in FRP composites in concrete construction”, Journal of Composites for Construction, ASCE, Vol. 11 No. 3, pp. 252–257.

13.

Rein

Empis

Abecassis C.

and Carvel

, eds. (2007). The Dalmarnock Fire Tests: Experiments and Modelling, The University of Edinburgh, Edinburgh, UK.

14.

Williams

Bibsy

Kodur

Green

and Chowdhury

(2006). “Fire insulation schemes for FRP-strengthened concrete slabs”, Composites Part A, Vol. 37, pp. 1151–1160.