Investigation of the Interface Fracture during Debonding between FRP and Masonry

Abstract

The masonry-FRP interface fracture is a topic of considerable research interest due to the heterogeneity of the masonry subgrade. The size of the material inhomgeneity associated with the presence of mortar joints is significant compared with the length scale of fracture process. In this paper, the results of an experimental investigation into the shear debonding of FRP sheets from brick, mortar and masonry blocks are reported. The test procedures (Ali-Ahmad et al. 2006,2007) developed previously for obtaining the FRP-concrete cohesive fracture response are applied to study interface debonding from the three substrates. During each test, spatially continuous measurements of the surface strains on the FRP and masonry are obtained using an optical technique known as digital image correlation. The interface cohesive fracture response of FRP-brick and the FRP-mortar interfaces are obtained from the results of the strain analysis. The interface fracture energy associated with the FRP-mortar interface is shown to be significantly smaller in magnitude than that of the FRP-brick interface. The contributions of the mortar and the brick to the overall load response of the masonry are analyzed using the cohesive material response of the FRP-brick and the FRP-mortar interfaces. It is shown that complete debonding is achieved at the FRP-mortar joint while the FRP is still attached to the bricks on either side of the joint. The cohesive crack front stretches across the fully debonded mortar joint before the cohesive crack completely crosses the joint. The local debonding at the mortar joint produces stresses higher than those associated with the main cohesive crack front in the brick-FRP interface close to the joint, thereby accelerating the crack advance.

Keywords

FRP masonry debonding mortar joints interface fracture cohesive material law mortar brick

Get full access to this article

View all access options for this article.

References

Ali-Ahmad

Subramaniam

K.V.

and Ghosn

(2006). “Experimental investigation and fracture analysis of debonding between concrete and FRP”, Journal of Engineering Mechanics, ASCE, Vol 132, No. 9, pp. 914–923.

Ali-Ahmad

Subramaniam

K.V.

and Ghosn

(2007). “Analysis of instability in FRP-concrete shear debonding for beam strengthening applications”, Journal of Engineering Mechanics, ASCE, Vol. 133, No. 1, pp. 58–67.

ACI 440.2R (2008). Guide for the Design and Construction of Externally Bonded FRP Systems for Strengthening Concrete Structures, American Concrete Institute.

Aiello

M.A.

and Sciolti

M.S.

(2004). “Influenza delle proprieta' dei materiali e della geometria dei campioni sull'aderenza fra nastri in FRP e pietra naturale”, Proceedings of the 2nd National Conference Meccanica delle Strutture in Muratura Rinforzate con FRP-materials, Venice, Italy, December 6–8, pp. 17–28.

Aiello

M.A.

and Sciolti

M.S.

(2006). “Bond analysis of masonry structures strengthened with CFRP sheets”, Construction and Building Materials, Vol. 20, pp 90–100.

Aiello

M.A.

Sciolti

M.S.

and Triantafillou

T.C.

(2007). “FRP-strengthened masonry: Bond aspects”, Proceedings of the FRPRCS-8, University of Patras, Patras, Greece, July 16–18.

Ali-Ahmad

(2005). Debonding of FRP from Concrete in Strengthening Applications: Experimental Investigation and Theoretical Validation, PhD Thesis, The Graduate School and University Center of The City University of New York, New York, USA.

Buyukozturk

and Hearing

(1998). “Failure behavior of precracked concrete beams retrofitted with FRP”, Journal of Composites for Construction, ASCE, Vol. 2, No. 3, pp. 138–144.

Buyukozturk

Gunes

and Karaca

(2004). “Progress on understanding debonding problems in reinforced concrete and steel members strengthened using FRP composites”, Construction and Building Materials, Vol. 18, pp. 9–19

10.

Carloni

Ali-Ahmad

and Subramaniam

(2005). “Scaling effect in FRP/concrete interface debonding”, Proceedings of the 7th International Conference on Mesomechanics, Montreal, August 1–4, pp. 37–42.

11.

Casareto

Olivieri

Romelli

and Lagomarsino

(2003). “Bond behaviour of FRP laminates adhered to masonry”, Proceeding of the Advancing with Composites (Plast 2003), Milan, Italy.

12.

Cosenza

Manfredi

Occhiuzzi

and Pecce

M.R.

(2000). “Towards the investigation of the interface behaviour between tuff masonry and FRP fabrics”, Proceedings of the National Conference Meccanica delle Strutture in Muratura Rinforzate con FRP-materials, Venice, Italy, December 7–8 2000, pp. 99–108.

13.

Kamel

A.S.

Elwi

A.A.

and Cheng

R.J.

, (2004). “Experimental investigation on FRP sheets bonded to concrete”, Emirates Journal for Engineering Research, Vol. 9, No. 2, pp. 71–76.

14.

Krevaikas

T.D.

and Triantafillou

T.C.

(2005). “Computer-aided strengthening of masonry walls using fibre-reinforced polymer strips”, Materials and Structures, Vol. 38, No. 1, pp. 1359–5997.

15.

Leung

C.K.Y.

(2001). “Delamination failure in concrete beams retrofitted with bonded plate”, Journal of Materials in Civil Engineering, ASCE, Vol. 13, No. 2, pp. 106–113.

16.

X.Z.

Teng

J.G.

L.P.

and Jiang

J.J.

(2005). “Bond-slip models for FRP sheets/plates bonded to concrete”, Engineering Structures, Vol. 27, No. 6, pp. 920–937.

17.

Moon

F.L.

(2003). Seismic Strengthening of Low-Rise Unreinforced Masonry Structures with Flexible Diaphragms, PhD Thesis, Georgia Institute of Technology, Atlanta, GA, USA.

18.

Mosallam

A.S.

(2007). “Out-of-plane flexural behaviour of unreinforced red brick walls strengthened with FRP composites”, Composites B: Engineering, Vol. 38, pp. 559–574.

19.

Olivito

R.S.

and Zuccarello

F.A.

(2006). “Experimental analysis on durability of brick-masonry panels subjected to cyclic loads”, SDHM, Vol. 2, No. 1, pp. 19–27.

20.

Prota

Manfredi

and Nardone

(2008). “Assessment of design formulas for in-plane strengthening of masonry walls”, Journal of Composites for Construction, ASCE, November/December 2008.

21.

Savoia

Ferracuti

and Mazzotti

(2003). “Non-linear bond-slip law for FRP-concrete interface”, Proceedings of the FRPRCS-6, Singapore, pp. 1–10.

22.

Stratford

Pascale

Manfroni

and Bonfiglioli

(2004). “Shear strengthening masonry panels with sheet glass-fiber reinforced polymer,” Journal of Composites for Construction, ASCE, Vol. 8, No. 5, pp. 434–443.

23.

Subramaniam

K.V.

Carloni

and Nobile

(2007). “Width effect in the interface fracture during debonding of FRP from concrete”, Engineering Fracture Mechanics, Vol. 74, No. 4, pp. 578–594.

24.

Sutton

M.A.

Wolters

W.J.

Peters

W.H.

Ranson

W.F.

and McNeill

S.R.

(1983). “Determination of displacements using an improved digital correlation method”, Image and Vision Computing, Vol. 1, No. 3, pp. 133–139.

25.

Taljsten

(1997). “Defining anchor lengths of steel and CFRP plates bonded to concrete”, International Journal of Adhesion and Adhesives, Vol. 17, No. 4, pp. 319–327.

26.

Tan

K.H.

and Patoary

M.K.H.

(2004). “Strengthening of masonry walls against out-of-plane loads using fiber-reinforced polymer reinforcement”, Journal of Composites for Construction, ASCE, January/February 2004.

27.

Teng

J.G.

Smith

S.T.

Yao

and Chen

J.F.

(2003). “Intermediate crack induced debonding in RC beams and slabs”, Construction and Building Materials, Vol. 17, pp. 447–462.

28.

Triantafillou

T.C.

and Pelvris

(1992). “Strengthening of RC beams with epoxy-bonded fiber-composite materials”, Material and Structures, Vol. 25, No. 149, pp. 201–211.

29.

Ueda

Sato

and Asano

(1999). “Experimental study on bond strength of continuous carbon fiber sheets”, Proceedings of the 4th International Symposium on Fiber Reinforced Polymer for Reinforced Concrete Structures, American Concrete Institute (SP-188), Detroit, MI, pp. 407–416.

30.

Matsuzaki

and Tanabe

(1997). “Interface crack propagation in FRP-strengthened concrete structures”, Non-Metallic (FRP) Reinforcement for Concrete Structures, Japan Concrete Institute, Vol. 1, pp. 319–326.

31.

Xia

and Oehlers

(2006). “Debonding mechanisms in FRP plated unreinforced masonry under out-of-plane loading”, Advances in Structural Engineering, Vol. 9, No. 5, pp. 619–637.