Tests were conducted on three hollow partially prestressed concrete beams subjected to combined loading in bending, shear and torsion. The beams were designed using the Direct Design Method which is based on the Lower Bound Theorem of the Theory of Plasticity. All beams were of 300 × 300 mm cross-section, 3.8 m in length, and possessed a 200 × 200 mm hollow core and 50 mm wall thickness. The two main variables studied were the ratio in the web of the maximum shear stress due to the twisting moment, to the shear stress arising from the shear force, which varied between 1.09 and 6.85, and the ratio of the maximum twisting moment to the maximum bending moment which varied between 0.35 and 2.62. Good agreement was found between design and experimental failure loads. All beams failed near the design loads and underwent ductile behaviour up to failure. The results indicate that the Direct Design Method can be successfully used to design partially prestressed concrete hollow beams which will cater for the combined effect of bending, shear and torsion loads.
LailaAbdel-Hafez M. (1986). Direct Design of Reinforced Concrete Skew Slab, PhD Thesis, University of Glasgow.
2.
ACI Committee 318 (2002). Building Code Requirements for Structural Concrete (ACI 318–02), American Concrete Institute, Farmington Hills, MI, 48333–9094, USA.
3.
AguilarG.MatamorosA. B.Parra-MontesinosG.J.RamrazJ.A. and WightJ.K. (2002). “Experimental evaluation of design procedures for shear strength of deep reinforced concrete beams”, ACI Structural Journal, Vol. 99, No. S56, pp. 539–548.
4.
AlnuaimiA.S. and BhattP. (2004a). “Direct design of hollow reinforced concrete beams – Part I: Design procedure”, Structural Concrete Journal, Vol. 5, No. 4, pp. 139–146.
5.
AlnuaimiA.S. and BhattP. (2004b). “Direct design of hollow reinforced concrete beams – Part II: Experimental investigation”, Structural Concrete Journal, Vol. 5, No. 4, pp. 147–160.
6.
BhattP. and BensalemA. (1996). “Behaviour of reinforced concrete flat slab over column support using nonlinear stress field design”, Structural Engineering Review, Vol. 8, No. 2–3, pp. 201–212.
7.
BhattP. and BensalemA. (1996a). “Use of non-elastic stress in the design of reinforced concrete deep beams”, Structural Engineering Review, Vol. 8, No. 2–3, pp. 213–225.
8.
BhattP. and EbireriJ. O. (1989) Direct Design of Beams for Combined Bending and Torsion, Stavebnicky Casopis, Building Journal (Bratislava), Vol. 37, No. 4 Apr., pp. 249–263, in English, ISSN: 0039–078X, Coden: STVCA2
9.
BhattP. and MousaJ. (1996a). “Tests on concrete box beams under non-monotonic loading”, Structural Engineering Review, Vol. 8, No. 2–3, pp. 227–235.
10.
BS8110 (1997). Structural Use of Concrete, Part1: Code of Practice for Design and Construction, British Standard Institution, 389 Chiswick High Road, London, W44AL.
11.
ClarkL.A. (1976). “The provision of tension and compression reinforcement to resist in-plane forces”, Magazine of concrete research, Vol. 28, No. 94, pp. 3–12.
12.
CohnM.Z. and LounisZ. (1993). “Optimum limit design of continuous prestressed concrete beams”, Journal of Structural Engineering, ASCE, Vol. 119, No. 12, pp. 3551–3569.
13.
ElarabiH. (1999). “Application of the direct design method on reinforced concrete beams subjected to combined torsion, bending and shear”, Building and Road Research Journal, University of Khartom, Vol. 2, pp. 47–56.
14.
El-HusseinE.A. (1994). “Finite element and direct design method in combined torsion, bending and shear of reinforced Concrete”, Computational Structural Engineering for Practice, Civil-Comp Ltd, Edinburgh, Scotland, pp. 165–171.
15.
El-NuonuG.F.R. (1985). Design of Shear Wall-floor Slab Connections, PhD Thesis, University of Glasgow.
16.
HagoA. and BhattP. (1986). “Tests on reinforced concrete slabs designed by direct design procedure”, ACI Journal, No. 83–79, pp. 916–924.
17.
HsuT.T. (1997). “ACI shear and torsion provisions for prestressed hollow girders”, ACI Structural Journal, Vol. 94–S72, No. 6, pp. 787–799.
18.
KarayannisC.G. and ChaliorisC.E. (2000). “Strength of prestressed concrete beams in torsion”, Structural Engineering and Mechanics, Vol. 10, No. 2, pp. 165–180.
19.
KempK.O. (1971). “Optimum reinforcement in a concrete slab subjected to multiple loadings”, Publications of the International Association of Bridge and Structural Engineering, pp. 93–105.
20.
MemonM. (1984). Strength and Stiffness of Shear Wall-floor Slab Connections, PhD Thesis, University of Glasgow.
21.
MorleyC.T. and GulvanessianH. (1977). “Optimum reinforcement of concrete slab elements”, Proceedings of the Institution of Civil Engineers, Part 2, Vol. 63, pp. 441–454.
22.
NielsenM.P. (1974). Optimum Design of Reinforced Concrete Shells and Slabs, Structural Research Laboratory, Technical University of Denmark, Report NR.R44, pp. 190–200.
23.
NielsenT.B. (1985). “Optimization of reinforcement in shells, folded plates, walls and slabs”, ACI Journal, Vol. 82–26, No. 3, pp. 304–309.
24.
PCI Design Handbook (2004). Pre-cast and Prestressed Concrete, Sixth edition, Pre-cast/Prestressed Concrete Institute, Chicago, IL.
25.
PoulsenP.N. and DamkildeL. (2000). “Limit state analysis of reinforced concrete plates subjected to in-plane forces”, International Journal of Solids and Structures, Vol. 37, No. 42, pp. 6011–6029.
26.
RahalK. and CollinsM.P. (1996). “Simple model for predicting torsional strength of reinforced and prestressed concrete sections”, ACI Structural Journal, Vol. 93–S62, No. 6, pp. 658–666.
27.
RahalK.N. (2001). “Analysis and design for torsion in reinforced and prestressed concrete beams”, Structural Engineering and Mechanics, Vol. 11, No. 6, pp. 575–590.
28.
RahalK.N. and CollinsM.P. (2003a). “Combined torsion and bending in reinforced and prestressed concrete beams”, ACI Structural Journal, Vol. 100, No. 2, pp. 157–165.
29.
RahalK. N. and CollinsM. P. (2003b). “Experimental evaluation of ACI and ASHTO-LRFD design provisions for combined shear and torsion”, ACI structural Journal, Vol. 100, No. S29, pp. 277–282.
30.
SerajS.M.KotsovosM.D. and PavlovicM.N. (1993). “Compressive-force path and behaviour of prestressed concrete beams”, Materials and Structures, Vol. 26, No.156, pp. 74–89.
31.
ZiaP. and HsuT.T.C. (2004). “Design for torsion and shear in prestressed concrete flexural members”, PCI Journal, Vol. 49, No. 3, pp. 34–42.
