Reinforced concrete walls with openings are tested in both one-way and two-way action. The test panels, with a slenderness ratio of 30 or 40, were subjected to a uniformly distributed axial load with an eccentricity of tw/6. Apart from highlighting the experimental set-up; typical crack patterns, failure modes, and load-deflection behaviour are also reported. Utilising these and other published test results, a formula predicting the ultimate load of walls with openings was derived. A comparative study of predicted to test results indicates that the new formula is accurate and reliable.
ACI 318 (2002). Building Code Requirements for Reinforced Concrete ACI318–02, American Concrete Institute, Detroit, pp. 111.
2.
BS8110–1997 (1997). Structural Use of Concrete, Part 1 – Code of Practice for Design and Construction, British Standards Institution, London, 1997.
3.
DohJ.H. (2003). Experimental and Theoretical Studies of Normal and High Strength Concrete Wall Panels, PhD Thesis, Griffith University, Australia.
4.
DohJ.H. and FragomeniS. (2005). “Evaluation of experimental work on concrete walls in one and two-way action”, Australian Journal of Structural Engineering, Vol. 6, No. 1, pp. 37–52.
5.
DohJ.H.FragomeniS. and LooY.C.(2002). “Evaluation of experimental behaviour of normal and high strength reinforced concrete walls in two-way action”, Proceedings of the 17th Advanced in Mechanics of Structures and Materials, Gold Coast, Australia, June, pp. 169–173.
6.
FragomeniS. and MendisP.A. (1997a), “Design equations for normal and high strength concrete walls”, Concrete in Australia, Concrete Institute of Australia, North Sydney, Vol. 23, No. 3, pp. 22–24.
7.
FragomeniS. and MendisP.A. (1997b). “Instability analysis of normal- and high-strength reinforced-concrete walls”, Journal of Structural Engineering, ASCE, Vol. 123, No. 5, pp. 680–684.
8.
FragomeniS. and MendisP.A. (1999). “Applicability of current ACI318 wall design formula for high strength concrete walls”, Advances in Structural Engineering, Vol. 2, No. 2, pp. 103–108.
9.
OberlenderG.D. (1973). Strength Investigation of Reinforced Concrete Load Bearing Wall Panels, PhD thesis, University of Texas, Arlington.
10.
PillaiS.U. and ParthasarathyC.V. (1977). “Ultimate strength and design of concrete walls”, Building and Environment, London, Vol. 12, pp. 25–29.
11.
SahebS.M. and DesayiP. (1989). “Ultimate strength of RC wall panels in one-way in-plane action”, Journal of Structural Engineering, ASCE, Vol. 115, No. 10, pp. 2617–2617.
12.
SahebS.M. and DesayiP. (1990). “Ultimate strength of RC wall panels in two-way in-plane action”, Journal of Structural Engineering, ASCE, Vol. 116, No. 5, pp.1384–1402.
13.
SahebS.M. and DesayiP. (1990b). “Ultimate strength of RC wall panels with openings”, Journal of Structural Engineering, ASCE, Vol. 116, No. 6, pp. 1565–1578.
14.
SanjayanJ.G. and MaheswaranT. (1999). “Load capacity of slender high-strength concrete walls with side supports”, ACI Structural Journal, Vol. 96, No. 4, pp. 571–576.
15.
SeddonA.E. (1956). “The strength of concrete walls under axial and eccentric loads”, Symposium on Strength of Concrete Structures, Cement and Concrete Association, May, London.
16.
AustraliaStandard. (2001). Australian standard 3600, Concrete Structure, Sydney.
17.
SwartzS.E.RosebraughV.H. and BermanM.Y. (1974). “Buckling test of rectangular concrete panels”, American Concrete Institute Journal, Vol. 71, pp. 33–39.
18.
ZielinskiZ.A.TroitskiM.S. and ChristodoulouH. (1982). “Full-scale bearing strength investigation of thin wall-ribbed reinforced concrete panels”, American Concrete Institute Journal, Vol.79, pp. 313–321.
19.
ZielinskiZ.A.TroitskiM.S. and El-ChakiehE. (1983). “Bearing capacity tests on precast concrete thin-wall ribbed panels”, Prestressed Concrete Institute Journal, Chicago, Vol. 28, No. 3, pp. 89–103.
