A new method has been developed for strengthening reinforced concrete beams for flexure which uses multiple mechanical fasteners to attach a fiber reinforced polymer (FRP) strip to the member. This study investigates the behavior of the method on full scale concrete T beams of three different steel reinforcement levels. The beams were strengthened without surface preparation, and the strips were attached with only four man-hours of labor per beam. The strengthened beams resulted in increases of up to 11.7 % in the yield moment and up to 27.2 % in the moment capacity at a deflection of L/135. The beams exhibited large amounts of ductility, before failure.
AASHTO (2002). Standard Specifications for Highway Bridges, 17th ed., American Association of State Highway and Transportation Officials, Washington DC.
2.
ACI Committee 318 (1999). Building Code Reqiorements for Structural Concrete (318–99) and Commentary (318R-99), American Concrete Institute, Farmington Hills, MI.
3.
Abd-El-NabyS. F. M. and HollawayL. (1993). “The experimental behavior of bolted joints in pultruded glass/polyester material. Part 1: Single-Bolt Joints”, Composites, Vol. 24, No. 7, pp. 531–538.
4.
ASTM D3039, Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials, American Society for Testing and Materials, West Conshohocken, Pa.
5.
ASTM D5766, Standard Test Method for Open Hole Tensile Strength of Polymer Matrix Composite Laminates, American Society for Testing and Materials, West Conshohocken, Pa.
6.
BankL. C.BorowiczD. T.LamannaA. J.RayJ. C. and VelazquezG. I. (2002b). Rapid Strengthening of Full-Sized Concrete Beams with Powder-Actuated Fastening Systems and Fiber-Reinforced Polymer (FRP) Composite Materials, US Army Corps of Engineers Engineer Research and Development Center, ERDC/GSL TR-02-12, July.
7.
BankL. C.LamannaA. J.RayJ. C. and VelazquezG. I. (2002a). Rapid Strenthening of Reinforced Concrete Beams with Mechanically Fastened, Fiber-Reinforced Polymeric Composite Strips, US Army Corps of Engineers Engineer Research and Development Center, ERDC/GSL TR-02-4, March.
8.
Hilti (2001). North American Product Technical Guide, Hilti Inc., Tulsa OK.
9.
LamannaA. J.BankL. C. and ScottD. W. (2004). “Flexural strengthening of RC beams by mechanically attaching FRP strips”, ASCE Journal of Composites for Construction, Vol. 8, No. 3, in press May-June.
10.
LamannaA. J.BankL. C. and ScottD. W. (2001a). “Flexural strengthening of RC beams using fasteners and FRP strips”, ACI Structural Journal, Vol. 98, No. 3, pp. 368–376.
11.
LamannaA. J.BankL. C. and ScottD. W. (2001b). “Rapid flexural strengthening of RC beams using powder actuated fasteners and FRP strips”, FRPRCS-5 Fiber Reinforced Plastics for Reinforced Concrete Structures, University of Cambridge, UK, Vol. 1, pp. 389–397.
12.
ParkR. and PaulayT. (1975). Reinforced Concrete Structures, John Wiley and Sons, New York.
13.
SoroushianP. and ChoiK. B. (1991). “Analytical evaluation of straight bar anchorage design in exterior joints”, ACI Structural Journal, Vol. 88, No. 2, pp. 161–168.
14.
SpadeaG.BencardinoF. and SwamyR. N. (1998). “Structural behavior of composite RC beams with externally bonded CFRP”, ASCE Journal of Composites for Construction, Vol. 2, No. 3, pp. 132–137.
15.
SpadeaG.SwamyR. N. and BencardinoF. (2001). “Strength and ductility of RC beams repaired with bonded CFRP laminates,”ASCE Journal of Bridge Engineering, Vol. 6, No. 5, pp. 349–354.
16.
StockdaleJ. H. and MatthewsF. L. (1976). “The effect of clamping pressure on bolt bearing loads in glass fibre-reinforced plastics”, Composites, Vol. 7, No. 1, pp. 34–38.
