Department of Civil and Environmental Engineering, University of Missouri-Columbia, Columbia MO 65211–2200, U.S.A. The effects of strain rate on the mechanical properties of carbon steel and plain concrete are investigated through a rate-dependent elasto-plasticity model and rate-dependent elasto-damage model, respectively. Continuum tangent stiffness tensors are derived for both models so that bifurcation analyses can be performed to identify the onset of material failure. Three-dimensional constitutive model solvers are designed and the numerical results are compared with the experimental data to verify the proposed models.
BarracloughD.R. and SellarsC.M. (1974) “The Effect of Varying Deformation Conditions during Hot Torsion Testing”. Inst. Phys. Conf. Series, Vol. 21, pp. 111.
2.
CampbellJ.D. and DubyJ. (1956) “The Yield Behavior of Mild Steel in Dynamic Compression”, Proc. Roy. Soc., London, Ser. A, Vol. 236, pp. 24–40.
3.
ChangK.C. and LeeG.C. (1987) “Strain Rate Effect on Structural Steel Under Cyclic Loading”, Journal of Engineering Mechanics, Vol. 113, No. 9, pp. 1292–1301.
4.
ChatfieldD.A., and RoteR.R. (1974) “Strain Rate Effects on the Properties of High Strength Low Alloy Steel”, paper 740177, SAE Automotive Engineering Congress, Detroit, February.
5.
ChenE.P. and TaylorL.M. (1986) “Fracture of Brittle Rock under Dynamic Loading Conditions”, Fracture Mechanics of Ceramics, Published by Plenum Press, New York, NY, Vol. 7, pp. 175–186.
6.
ChenZ. (1993) “Modification and Implementation of a Brittle Damage Model for Concrete”, NMERI-OC-94-6, University of New Mexico, prepared for Sandia National Laboratories, Albuquerque, NM, USA
7.
ChenZ.HuW., and ChenE.P. (2000) “Simulation of Dynamic Failure Evolution in Brittle Solids without Using Nonlocal Terms in the Strain-Stress Space”, Computer Modeling in Engineering & Sciences, Vol.1, No. 4, pp.101–106.
8.
ChenZ. and SchreyerH. L. (1995) Formulation and Computational Aspects of Plasticity and Damage Models with Application to Quasi-Brittle Materials, SAND95–0329, Sandia National Laboratories, Albuquerque, NM, USA
9.
CowperG.R. and SymondsP.S. (1957) Strain Hardening and Strain Rate Effects in Impact Loading of Cantilever Beams, Tech Report No. 28, ONR contract No. 562(10), Division of Engineering, Brown University, Providence, RI, USA.
10.
EtseG. and WillamK. (1999) “Failure analysis of elastoviscoplastic material models”, Journal of Engineering Mechanics-ASCE, Vol.125, No.1, pp.60–69.
11.
FuH.C.ErkiM.A. and SeckinM. (1991) “Review of Effects of Loading Rate on Concrete in Compression”, Journal of Structural Engineering, Vol. 117, No. 12, pp. 3645–3658.
12.
GreenA.E., and NaghdiP.M. (1967) “A Class of Viscoelastic-Plastic Media”, Acta Mechanica, Vol. IV, No. 3, pp. 228–295.
13.
HaqueM.M.HashmiM.S.J. and PickeringF.B. (1987) “Effects of Strain Rate and Strain Rate History on a Medium Carbon Steel at Room Temperature”, Material Forum, Vol. 10, No. 3, pp. 214–217.
14.
HashmiM.S.J. and HamoudaA.M.S. (1994) “Development of a One-Dimensional Constitutive Equation for Metals Subjected to High Strain Rate and Large Strain”, Journal of Strain Analysis, Vol. 29, No. 2, pp. 117–127.
15.
JohnsonG.R. and CookW.H. (1983) “A Constitutive Equation and Data for Metals subjected to Large Strains, High Strain Rates and High Temperatures”, Proceedings of the Seventh International Symposium on Ballistics, pp.541.
16.
MalvernL.E. (1951) “The Propagation of Longitudinal Waves of Plastic Deformation in a Bar of Material Exhibiting a Strain-Rate Effect”, Journal of Applied MechanicsVol.18, pp. 203–208.
17.
ManjoineM.J. (1944) “Influence of Rate of Strain and Temperature on Yield Stresses of Mild Steel”, Journal of Applied Mechanics, ASCE Transactions, Vol. 11, No. 4, pp. A-211–A-218.
18.
NaghdiP. M., and MurchS. A. (1963) “On the Mechanical Behavior of Viscoelastic/Plastic Solids”, Journal of Applied Mechanics, Vol. 30, pp. 321–328.
19.
PerzynaP. (1966) “Fundamental Problems in Viscoplasticity”, Advances in Applied Mechanics, Academic Press, New York, Vol. 9, pp. 243–296.
20.
RubinM.B. (1982) “A Thermoelastic-Viscoplastic Model with a Rate-Dependent Yield Strength”, Journal of Applied Mechanics, Vol. 49, June, pp. 305–311.
21.
SaxenaA. and ChatfieldD. A. (1976) “High Strain Rate Behavior of Some Hot and Cold Rolled Low Carbon Steels”, Automotive Engineering Congress and Exposition, Society of Automotive Engineers, Feb., pp. 1–19.
22.
SoroushianP. and ChoiK. B. (1987) “Steel Mechanical Properties at Different Strain Rates”, Journal of Structural Engineering, Vol. 111, No. 4, pp. 663–672.
23.
SoroushianP.ChoiK. B. and AlhamadA. (1986) “Dynamic Constitutive Behavior of Concrete”, ACI Journal, Vol. 83, No. 2, Mar.-Apr., pp. 252–259.
24.
TaylorL.M.ChenE.P. and KuszmaulJ.S. (1986) “Microcrack-Induced Damage Accumulation in Brittle Rock under Dynamic Loading”, Computer Methods in Applied Mechanics and Engineering, Vol. 55, pp. 301–320.
25.
WillamK.EtseG. and MunzT. (1993) “Localized Failure in Elastic-viscoplastic Materials”, Creep and Shrinkage of Concrete. E & FN Spon, London, pp.327–344.
26.
WilsonM.L.HawleyR.H. and DuffyJ. (1979) The Effect of Loading Rate and Temperature on Fracture Initiation in 1020 Hot-rolled Steel, Brown University Report NSF-ENG 75-18532/8.
27.
WinlockJ. and LeiterR. (1937) “Some Factors Affecting the Plastic Deformation of Sheet and Strip Steel and their Relation to the Deep Drawing Properties”, Transaction, American Society for Metals, Vol. 25, Mar., pp. 163–185.
