The safe operation of a wide range of large-scale plant depends on knowledge of component specific materials properties. Techniques that allow reliable measurement of changes in critical properties are therefore vital. The present paper describes a new procedure for removing miniature material samples. The technique can be applied even in difficult access conditions and results in minimum material removal so that sampling is effectively non-destructive. Specific case studies where this technique has been applied to the condition assessment of steam plant are described.
Get full access to this article
View all access options for this article.
References
1.
GoochD. J.TownsendR. D.CEGB remanent life procedures. In Life extension and assessment of fossil power plants: Conference Proceedings (Eds DooleyR. B.ViswanathanR.) 1987, EPRI CS–5208 (Electric Power Research Institute, Palo Alto, Calif.).
2.
ParkerJ. D.SideyD.Residual life of boiler components. Mater. Forum, 1986, 9(1 and 2).
3.
CoadeR. W.MannS. D.Creep life assessment procedures and a computer based creep life assessment programme. Report SO/85/92, State Electricity Commission of Victoria, 1985.
4.
ParkerJ. D.McMinnA.BellR. J.RichmanR. H.McNaughtonW. P.Condition assessment guidelines for fossil-fuel power plant components, EPRI GS–6724, Electric Power Research Institute, Palo Alto, Calif., 1990.
5.
HarrisD. O.ParkerJ. D.WellsC. H.Optimization of plant maintenance. Third International Congress on Condition monitoring and diagnostic engineering management, 1991 (IOP Publishing Limited).
6.
DérT. J.LonsdaleD.StevensR. A.ChastellD. J.FlewittP. E. J.Methods of sampling service components for metallurgical evaluation of remanent creep life. SE/SSD/RN/81/067, Central Electricity Generating Board, 1981.
7.
AskinsM. C.MerchantK. D.Remaining life estimation of boiler pressure parts, Vol. 2, Miniature specimen creep testing, 1988, CS–5588 (Electric Power Research Institute, Palo Alto, Calif.).
8.
ParkerJ. D.McMinnA.FouldsJ.Material sampling for the assessment of component integrity. Pressure Vessel and Piping Conference, Vol. 171, 1989 (American Society of Mechanical Engineers).
9.
BeckerF. L.WalkerS. M.DooleyR. B.Industry experience and overview of steam pipe activities. Conference Proceedings on life extension and assessment of fossil power plants (Eds DooleyR. B.ViswanathanR.), 1987, CS–5208, p. 839 (Electric Power Research Institute, Palo Alto, Calif.).
10.
WolstenholmeD.Transverse cracking and creep ductility of 2CrMo weld metal. Conference on Trends in steels and consumables for welding, 1978 (The Welding Institute).
11.
Life assessment methodology for turbogenerator rotors, Vols I–IV, 1988, projects RP–2481–3; 2785–1 (Electric Power Research Institute, Palo Alto, Calif.).
12.
ViswanathanR.BruemmerS. M.RichmanR. H.Etching techniques for assessing toughness degradation of in-service components. Trans. ASME, J. Engng Mater. Technol., 1988, 110..
13.
RichmanR. H.CargillR. L.BruemmerS. M.GehlS. M.Non-destructive methods for assessing temper embrittlement of in-service conditions. Second EPRI Conference on Fossil plant inspection, San Antonio, Tex., 1988.
14.
ViswanathanR.JaffeeR. I.Toughness of CrMoV steels for steam turbine rotors. Trans. ASME, J. Engng Mater. Technol., 1983, 105..
15.
ViswanathanR.BruemmerS.In-service degradation of rotors. Trans. ASME, J. Engng Mater. Technol., 1985, 107..
16.
BaikJ.-M.KamedaJ.BuckO.Development of small punch tests for ductile–brittle transition temperature measurement of temper embrittled Ni–Cr steels. ASTM STP 888, ASTM, Philadelphia, 1986.
17.
LucasG. E.Review of small specimen test techniques for irradiation testing. Met. Trans., 1990, 21A..
