Investigations Concerning Flow Conditions in a Centrifugal Pump,and the Effect of Blade Loading on Head Slip

Abstract

The object of the paper is to examine the flow conditions observed in a specially designed 6-inch centrifugal pump; firstly, when the directions and magnitudes of velocities of flow were obtained by means of Pitot tubes, and secondly, when the flow was examined with an electronic stroboscope, through an inspection window of “Armourplate” glass in the casing.

To provide uniform entry conditions a single-entry pump was chosen, preceded by a long length of straight suction-piping, but at small discharges a powerful forced vortex was found to exist with a spiral flow extending backwards for some distance from the pump inlet. This phenomenon was investigated by traverses with a direction vane and Pitot tubes, and an explanation of its cause is offered.

The direction and magnitude of the absolute velocity at the impeller outlet were measured by cylindrical Pitot-tube traverses across the passage at two positions, and at small discharges a component of flow from the casing towards the suction side was found to occur through a portion of the impeller on the side nearest to the suction pipe. Similar traverses were made at two positions around the volute casing. These indicated a symmetrical, double spiral-flow at the best-efficiency point, and at other discharges this was modified to a single-direction vortex having a core at a much lower pressure than that on the outside of the casing.

Pressure tappings on the casing, with an open-sided impeller and diffuser, showed the effect of shock on the inlet tips of the diffuser vanes, and inspection through the window confirmed a flow surging to and fro at small discharges.

The effect of impeller blade loading on “head slip” is also investigated—two impellers showed a direct relationship—and values of the resulting “slip constant” are given. A graphical analysis shows the head slip, and head losses in the impeller and casing for the full range of discharge.

Finally the performance curves of the pump, operating in reverse as a turbine, are given, from which the “runaway” speed under any head and any resisting torque may be estimated.

Get full access to this article

View all access options for this article.

References

Anderson

H. H.

1947 Proc. I. Mech. E., vol. 157, p. 57, “Centrifugal Pumps—an Alternative Theory”.

Binder

R. C.

Knapp

R. T.

1936 Trans. A. S. M. E., vol. 158, p. 649, “Experimental Determinations of the Flow Characteristics in the Volutes of Centrifugal Pumps”.

Blom

1949 A. S. M. E. Paper no. 49-SA-8, “Development of the Hydraulic Design for the Grand Coulee Pumps”.

Fischer

Thoma

1932 Trans. A. S. M. E., vol. 154, p. 141, “Investigation of Flow Conditions in a Centrifugal Pump”.

Gibson

A. H.

1930 “Hydraulics and its Applications”. (Constable, London).

Gibson

A. H.

Ryan

1910 Proc. Inst. C. E., vol. 179, p. 313, “The Resistance to Rotation of Disks in Water at High Speed”.

Hagmayer

1932 Dissertation, Braunschweig, “Messungen des Druckverlaufes Über Lauf- und Leitschaufel einer Kreiselpumpe”.

Kasai

1936a Memoirs of the Faculty of Engineering, Kyushu Imperial University, Japan, vol. 8, no. 1, “On the Exit Velocity and Slip Coefficient of Flow at the Outlet of the Centrifugal Pump Impeller”.

1936b Trans. S. M. E., Japan, vol. 2, p. 235, “Variations of the Characteristics of the Centrifugal Pump and Flow Conditions at the Outlet of the Impeller due to the Difference of the Size of the Volute Chamber”.

10.

Kearton

W. J.

1933 Proc. I. Mech. E., vol. 124, p. 481, “The Influence of the Number of Impeller Blades on the Pressure Generated in a Centrifugal Compressor and on its General Performance”.

11.

Kittredge

C. P.

Thoma

1931 Power, vol. 73, p. 881, “Centrifugal Pumps Operated under Abnormal Conditions”.

12.

Knapp

R. T.

1937 Trans. A. S. M. E., vol. 59, p. 683, “Complete Characteristics of Centrifugal Pumps and their use in the Prediction of Transient Behavior”.

13.

1941 Trans. A. S. M. E., vol. 63, p. 251, “Centrifugal Pump Performance as Affected by Design Features”.

14.

Muysken

1937 De Ingenieur (Holland), vol. 52, p. 161, “Het Stroombeeld in een Centrifugaalpomp”.

15.

NÜll

1935 Dissertation, Braunschweig, “Untersuchungen am umlaufenden Kreiselpumpenrade Öber ArbeitsÜbertragung und Hohlraumbildung”.

16.

Oertli

1923 Dissertation, ZÜrich, “Untersuchung der Wasserstromung durch ein rotierendes Zellen-Kreiselrad”.

17.

Price

O. A.

1939 Proc. I. Mech. E., vol. 142, p. 413, “Vortex Pumps, or, Slip in the Centrifugal Pump”.

18.

Schröder

1933 Dissertation Technischen Hochschule, Braunschweig, “Das Förderhöhenverhältnis einer radialen Kreiselpumpe”.

19.

Schulz

1928 Forschungsarbeiten, no. 307, “Das Förderhöhenverhältnis der Kreiselpumpen fÜr die ideale und wirkliche FlÜssigkeit”.

20.

Sherwell

T. Y.

Pennington

1932 Proc. I. Mech. E., vol. 123, p. 621, “Centrifugal Pump Characteristics; Performance, Construction and Cost”.

21.

Terry

R. V.

Jaski

F. E.

1942 Trans. A. S. M. E., vol. 64, p. 731, “Test Characteristics of a Combined Pump-Turbine Model with Wicket Gates”.

22.

Theunissen

T. W.

1930 International Congress for General Mechanics, vol. 2, p. 203, “De l'influence du Nombre d'aubes sur les courbes caractéristiques des Pompes Centrifuges et le rôle de la couche limite”.

23.

Watson

R. M.

1947 Proc. Third International Conference on Industrial Hydraulics, United States, p. 50, “Cavitation in Centrifugal Pumps. Some of the less well known Factors”.