Paper 24: Hydrodynamic Journal Bearing Performance at High Speed under Steady Load

Woolacott R. G. ‘The performance at high speeds of complete plain journal bearings with a single hole oil inlet’, N.E.L. Report No. 194, 1965 (National Engineering Laboratory, East Kilbride, Glasgow).

Hunter J. J. Hughes C. J. ‘Shaft position indicator for use with journal bearings’, Br. J. appl. Phys. 1961 12 (2), 73.

Tipei N. Theory of lubrication 1962 (University Press, Oxford).

Dowson D. Hudson J. D. ‘Thermo-hydrodynamic analysis of the infinite slide bearing: Part 1—The plane-inclined slider-bearing’, Lubrication and Wear Convention (Bournemouth, 1963) 1964, 34 (Instn Mech. Engrs, London).

Wilcock D. F. Booser E. R. Bearing design and application 1957 (McGraw-Hill Book Co., New York).

Burke A. E. Neale M. J. ‘A method of designing plain journal bearings for steady loads’, Proc. Conf. Lubrication and Wear 1957, 118 (Instn Mech. Engrs, London).

Cole J. A. ‘An experimental investigation of temperature effects in journal bearings’, Proc. Conf. Lubrication and Wear 1957, 111 (Instn Mech. Engrs, London).

Cameron A. ‘Heat transfer in journal bearings: a preliminary investigation’, Proc. Gen. Disc. Heat Transfer 1952, 194 (Instn Mech. Engrs, London).

Burr A. H. ‘The effect of shaft rotation on bearing temperatures’, Trans. Am. Soc. lubric. Engrs 1960 2 (2), 235.

Barnard D. P. ‘Lubrication in plain bearings’, Trans. Soc. automot. Engrs 1926 21 (1), 143.

McKee S. A. ‘Oil flow in complete journal bearings’, Trans. Am. Soc. mech. Engrs 1952 74 (5), 841.

Cole J. A. Hughes C. J. ‘Oil flow and film extent in complete journal bearings’, Proc. Instn mech. Engrs 1956 170 (17), 499.

Clayton D. ‘An exploratory study of oil grooves in plain bearings’, Proc. Instn mech. Engrs 1946 155 (14), 41.

Ocvirk F. W. ‘Short bearing approximation for full journal bearing’, N.A.C.A. tech. Note 2808, 1952 (National Advisory Committee for Aeronautics, Washington, D.C.).

Cameron A. Wood W. L. ‘The full journal bearing’, Proc. Instn mech. Engrs 1949 161, 59.

Walther A. Sassenfeld H. ‘Pressure distribution and load in a 360° journal bearing, for values of characteristic B (ratio of diameter to length) from 0 to 8, and eccentricities C = 0.1 to C = 0.95’, Sponsored Research (Germany) Report No. 11, 1950 (Dept Scient. Indus. Res., London).

Raynor S. Charnes A. ‘Flow parameters in hydrostatic lubrication for several bearing shapes’, J. basic Engng, Trans. Am. Soc. mech. Engrs 1960 82 (2), 257.

Hirano F. Shôdai N. ‘Oil-flow coefficient of pressure fed journal bearing’. Bull. Japan Soc. mech. Engrs 1958 1 (2), 184.

Woolacott R. G. Underhill C. Mrs ‘Flow and load parameters for hydrostatic oil bearings’, N.E.L. Report No. 106, 1963 (National Engineering Laboratory, East Kilbride, Glasgow).

Loeb A. M. ‘The determination of the characteristics of hydrostatic bearings through the use of the electric analog field plotter’, Trans. Am. Soc. lubric. Engrs 1958 1 (1), 217.

Kingsbury A. ‘On problems in the theory of fluid film lubrication with an experimental method of solution’, Trans. Am. Soc. mech. Engrs 1931 53 (9), 59.

Horsnell R. McCallion H. ‘Prediction of some journal bearing characteristics under static and dynamic loading’, Paper 12, Lubrication and Wear Convention (Bournemouth, 1963) 1964, 126 (Instn Mech. Engrs, London).

Dubois G. B. Ocvirk F. W. ‘Experimental investigation of eccentricity ratio, friction, and oil flow of short journal bearings’, N.A.C.A. tech. Note 2809, 1952 (National Advisory Committee for Aeronautics, Washington, D.C.).

Hunter W. B. Zienkiewicz O. C. ‘Effect of temperature variations across the lubricant films in the theory of hydrodynamic lubrication’, J. mech. Engng Sci. 1960 2 (1), 52.

Wilcock D. F. ‘Predicting sleeve bearing performance’, Proc. Conf. Lubrication and Wear 1958, 82 (Instn Mech. Engrs, London).

Barwell F. T. ‘Bearing data: Can they be made more useful to designers?’ Paper 23, Lubrication and Wear Third Convention (London) 1965, 192 (Instn Mech. Engrs, London).