Operations Cycle of the Stirling Engine with Particular Reference to the Function of the Regenerator

Abstract

The basic elements of a Stirling engine, the regenerator and the compression and expansion spaces may be arranged in three different ways. The preferred arrangement is the displacer-piston in a single-cylinder system. With a machine of this type, acting as a refrigerator, some experiments were carried out to determine the effect of the regenerator on the machine output. The experimental regenerators were made up of packs of wire gauze. Different sizes and arrangements of meshes were tried, and it was found that dense meshes with small diameter wires gave the best results. The theory of the operational cycle of a Stirling engine is not fully developed, but a simplified theory can be used to investigate the effects of some of the independent design parameters. A recent more complex theory promises to make possible a closer relation of the experimental and theoretical performance of an engine.

The operating conditions of a regenerator in a Stirling engine are different from those assumed in the existing theory of regenerators developed mainly for application to gas turbines. Even so values for the efficiency of the regenerator in a particular case can be estimated using the theory. The few values obtained confirm the conclusions of the experimental work.

Get full access to this article

View all access options for this article.

References

Schmidt

1871 Z. Ver. dtsch. Ing., vol. 15, No. 1, ‘Theorie der Lehmann'schen calorischen Maschine’.

Zeuner

1887 ‘Technische Thermodynamik’, pp. 347–357, vol. 1 (Leipzig).

Grashof

1890 ‘Theorie der Kraftmaschinen’, (Hamburg).

Finkelstein

1960 Soc. automot. Engrs, N.Y., Annual Meeting, ‘Generalized thermodynamic analysis of Stirling engines’.

Stoddart

1960 University of Durham Thesis, ‘Generalized thermodynamic analysis of Stirling engines’.

Malone

J. F. J.

1931 J. roy. Soc. Arts, vol. LXXIX, p. 679, ‘A new prime mover’.

Finkelstein

1960 Soc. automot. Engrs, N.Y., Annual Meeting, ‘Optimization of phase angle and volume ratio for Stirling engines’.

Hausen

1929 Z. angew. Math. Mech., vol. 9, p. 173, ‘Uber die Theorie des Wärmeaustausches in Regeneratoren’ (‘On the theory of heat exchange in regenerators’, R.A.E. Library Translation No. 126).

1929 Z. Ver. dtsch. Ing., vol. 73., p. 432, Wärmeaustauch in Regeneratoren’.

10.

1931 Z. angew. Math. Mech., vol. 11, p. 105, ‘Näherungsverfahren zur Berechnung des Wärmeaustausches in Regeneratoren’, (‘An approximate method of dimensioning regenerative heat exchangers’, R.A.E. Library Translation No. 98).

11.

1942 Z. Ver. dtsch. Ing., Beiheft Verfahrenstechnik No. 2, p. 31, ‘Vervollständigte Berechnung des Wärmeaustauches in Regeneratoren’, (M.A.P. Reports and Translations No. 312, 1946).

12.

Nusselt

1927 Z. Ver. dtsch. Ing., vol. 71, p. 85, ‘Die Theorie des Winderhitzers’.

13.

1928 Z. Ver. dtsch. Ing., vol. 72, p. 1052, ‘Der Beharrungszustand im Winderhitzer’.

14.

Boestad

1938 Feuerungstecknik, Sweden, vol. 26, p. 282, ‘Die Wärmeübertragung im Ljungström Luftwärmer’.

15.

Iliffe

1948 Proc. Instn mech. Engrs, Lond., vol. 159, p. 363, ‘Thermal analysis of the contra-flow regenerative heat exchanger’.

16.

Saunders

Smoleniec

1948 Proc. Seventh Internat. Congr. appl. Mech. II, p. 91, ‘Heat regenerators’. 1951 Proc. Gen. Disc, on Heat Transfer (Instn mech. Engrs, Lond., Amer. Soc. mech. Engrs), p. 443, ‘Heat transfer in regenerators’.

17.

Johnson

J. E.

1952 Aero. Res. Counc. Technical Report R. & M. No. 2630 ‘Regenerator heat exchangers for gas turbines’.

18.

Tipler

1947 Shell Technical Report No. I.C.T./14, ‘A simple theory of the heat regenerator’.

19.

Schultz

B. H.

1951 Proc. Gen. Disc. on Heat Transfer (Instn mech. Engrs, Lond., Amer. Soc. mech. Engrs), p. 440, ‘Regenerators with longitudinal heat conduction’.

20.

1952 Appl. Sci. Res., vol. 3, p. 165, ‘Approximative formulae in the theory of thermal regenerators’.

21.

Williamson

J. M.

1959 English Electric Report No. W/M(4B), ‘The effectiveness of the periodic—flow heat exchanger’.

22.

Coppage

J. E.

London

A. L.

1953 Trans. Amer. Soc. mech. Engrs, vol. 75, p. 779, ‘The period flow regenerator–A summary of design theory’.

23.

Kays

W. M.

London

A. L.

1958 ‘Compact heat exchangers’ (McGraw-Hill, New York).

24.

1951 Proc. Gen. Disc. on Heat Transfer (Instn mech. Engrs, Lond., Amer. Soc. mech. Engrs), Closing Technical Session, p. 488, ‘Regenerator theory and measurement of heat transfer coefficients’, also p. 470, Discussion on Section V, Le Fevre E. J.

25.

Davies

S. J.

Singham

J. R.

1951 Proc. Gen. Disc. on Heat Transfer (Instn mech. Engrs, Lond., Amer. Soc. mech. Engrs), p. 434, ‘Experiments on a small thermal regenerator’.

26.

Murray

J. A.

Martin

B. W.

Bayley

F. J.

Rapley

C. W.

1961 Internat. Heat Transfer Conf. (Instn mech. Engrs, Lond., Amer. Soc. mech. Engrs), ‘Performance of thermal regenerators under sinusoidal flow conditions’.

27.

Kohler

J. W. L.

Jonkers

C. O.

1954 Philips Tech. Rev., vol. 16 (3), p. 69, ‘Fundamentals of the gas refrigerating machine’, vol. 16 (4), p. 105, ‘Construction of the gas refrigerating machine’.

28.

Meyer

R. J.

1958 Philips Tech. Rev., vol. 20 (9), p. 245, ‘The Philips hot gas engine with rhombic drive mechanism’.

29.

Emmerson

1958 University of Durham Thesis, ‘Effect of regenerator matrix arrangement on the performance of a gas refrigerating machine’.

30.

Dawson

P. H.

1961 Power Transmission, vol. 30, No. 351, p. 208, and No. 352, pp. 286, ‘Pitting of lubricated gear teeth and rollers’.

31.

Dawson

P. H.

‘Effect of Metallic Contact on Pitting’ (to be published).

32.

Crook

A. W.

1958 Phil. Trans. roy. Soc., Series A, No. 981, vol. 250, p. 387, ‘Lubrication of rollers’.