Numerical investigations of piston cooling using oil jet in heavy duty diesel engines

Abstract

Thermal loading of diesel engine pistons has increased dramatically in recent years owing to applications of various technologies to meet low emission and high power density requirements. Control of piston temperatures by cooling of these pistons has become one of the determining factors in a successful engine design. The pistons are cooled by oil jets fired at the underside from the crankcase. Any excessive piston temperature rise may lead to engine seizure because of piston warping. However, if the temperature at the underside of the piston, where the oil jet strikes the piston, is above the boiling range of the oil being used, it may contribute to the generation of mist. This mist significantly contributes to the non-tailpipe emissions in the form of unburnt hydrocarbons (UBHCs). The problem of non-tailpipe emissions has unfortunately not been looked into so seriously, as the current stress of all automobile manufacturers is to meet the tailpipe emission legislative limits.

A numerical model has been developed using finite element methods for studying the oil jet cooling of pistons and has been validated experimentally on a flat plate cooled by oil jet. Using numerical modelling, the heat transfer coefficient (h) at the underside of the piston is predicted. This predicted value of heat transfer coefficient significantly helps in selecting the correct oil type, oil jet velocity, oil jet diameter, and distance of oil nozzle from the underside of the piston. It also helps to predict whether the selected grade of oil will contribute to mist generation. Isotherms of the predicted temperature profiles in a production grade piston have been plotted.

Keywords

piston cooling oil jet non-tailpipe emissions cooling nozzle modelling pool boiling piston temperature profile oil grade

Get full access to this article

View all access options for this article.

References

Woschni

Fieger

Determination of local heat transfer coefficients at the piston of a high speed diesel engine by evaluation of measured temperature distribution

SAE paper 790834, 1979, pp. 2807–2815.

Ferguson

C. R.

Kirpatrick

A. T.

Internal combustion engines, 2001, p. 369 (John Wiley & Sons, New York).

Sanders

J. C.

Schramm

W. B.

Analysis of variation of piston temperature with piston dimensions and undercrown cooling

NACA report 895, 1946.

Manganiello

E. J.

Piston temperatures in an air-cooled engine for various operating conditions

NACA report 698, 1942.

Stotter

Heat transfer in piston cooling

SAE paper 660757, 1966, pp. 705–710.

Dhariwal

H. C.

Control of blowby emissions and lubricating oil consumption in IC engines

Energy Conversion Management 1997, 38(10–13), 1267–1274.

Martin

Heat and mass transfer between impingement gas jets and solid surfaces

Advances in Heat Transfer 1977, 13, 1–60.

Down

S. J.

James

E. H.

Jet impingement heat transfer - a literature survey

ASME paper 87-HT-35, 1987.

Hrycak

Heat transfer from impingement jets to a flat plate

Int. J. Heat and Mass Transfer 1988, 26, 1857–1865.

10.

Sparrow

E. M.

Lovell

B. J.

Heat transfer characteristics of an obliquely impinging circular jet

Trans. ASME, J. Heat Transfer 1980, 102

11.

C. H.

Lienhard

V. J. H.

Younis

H. F.

Dahbura

R. S.

Michels

Liquid jet-array cooling modules for high fluxes

Alche J. Fluid Mechanics and Transport Phenomena April 1998, 44(4), 769–779.

12.

Wen

M.-Y.

Jang

K.-J.

An impingement cooling on a flat surface by using circular jet with longitudinal swirling strips

Int. J. Heat and Mass Transfer 2003, 46(24), 1–12.

13.

Oliphant

Webb

B. W.

Mcquay

M. Q.

An experimental comparison of liquid jet array and spray impingement cooling in the non-boiling regime

Expl Thermal and Fluid Sci. 1998, 18, 1–10.

14.

Cornaro

Fleischer

A. S.

Rounds

Goldstein

R. J.

Jet impingement cooling of a convex semi-cylindrical surface

Int. J. Thermal Sci. 2001, 40, 890–898.

15.

Bush

J. E.

Heat transfer in a reciprocating hollow piston partially filled with a liquid. Technical report 51, Stanford University, 1961.

16.

French

C. C. J.

Piston cooling

SAE paper 720024, 1972.

17.

Evans

C. A.

Cocktail shaker. Heat Transfer Science Library, University of Nottingham, 1977.

18.

Kajiwara

Fujioka

Suzuki

Negishi

An analytical approach for prediction of piston temperature distribution in diesel engines

J. Soc. Automot. Engrs Rev. 2002, 23, 429–434.

19.

Leites

J. M. M.

De Camargo

R. C.

Articulated piston cooling optimization

SAE paper 930276, 1993.

20.

Pimenta

M. M.

Cooling of automotive pistons: Study of liquid-cooling jets

Escola Politécnica da USP, SAE paper 931622, 1993.

21.

Stevens

Webb

B. W.

The effect of inclination on local heat transfer under an axisymmetric, free liquid jet

Int. J. Heat Transfer 1991, 34(4/5), 1227–1236.

22.

Stevens

Webb

B. W.

Local heat transfer coefficient under an axisymmetric, single-phase liquid jet

Trans. ASME, J. Heat Transfer 1991, 113, 71–78.

23.

Ghoshdastidar

P. S.

Computer simulation of flow and heat transfer, 1998 (Tata McGraw-Hill Publishing, New Delhi).

24.

Verghese

M. B.

Agarwal

A. K.

Numerical investigations of piston cooling using oil jet SAE paper 2004-28-0061, 2004; In Proceedings of the Third International Conference on Synergy of fuel and automotive technology for a cleaner environment, New Delhi, India.

25.

Muralidhar

Sundararajan

Computational fluid flow and heat transfer, 2003 (Narosa Publishing House, New Delhi).