Modelling Commercial Vehicle Handling and Rolling Stability

Abstract

This paper presents a multi-degrees-of-freedom non-linear multibody dynamic model of a three-axle heavy commercial vehicle tractor unit, comprising a subchassis, front and rear leaf spring suspensions, steering system, and ten wheels/tyres, with a semi-trailer comprising two axles and eight wheels/tyres. The investigation is mainly concerned with the rollover stability of the articulated vehicle. The models incorporate all sources of compliance, stiffness, and damping, all with non-linear characteristics, and are constructed and simulated using automatic dynamic analysis of mechanical systems formulation. A constant radius turn test and a single lane change test (according to the ISO Standard) are simulated. The constant radius turn test shows the understeer behaviour of the vehicle, and the single lane change manoeuvre was conducted to show the transient behaviour of the vehicle. Non-stable roll and yaw behaviour of the vehicle is predicted at test speeds >90 km/h. Rollover stability of the vehicle is also investigated using a constant radius turn test with increasing speed.

The articulated laden vehicle model predicted increased understeer behaviour, due to higher load acting on the wheels of the middle and rear axles of the tractor and the influence of the semi-trailer, as shown by the reduced yaw rate and the steering angle variation during the constant radius turn. The rollover test predicted a critical lateral acceleration value where complete rollover occurs. Unstable behaviour of the articulated vehicle is also predicted in the single lane change manoeuvre.

Keywords

commercial vehicle dynamics articulated multibody dynamics handling stability rollover

Get full access to this article

View all access options for this article.

References

Matteson

Blower

Trucks involved in fatal accidents In Codebook 2000, 2003 (University of Michigan, Transportation Research Institute, Ann Arbor).

North Carolina Department of Transportation Division of Motor Vehicles.

Driving combination vehicles safely (Internet) (cited 17th April), 2004, available from http://www.dmv.dot.state.nc.us/driverlicense/CDL/handbook/driving_combos.html

Gillespie

T. D.

Fundamentals of vehicle dynamics, 1992 (Society of Automotive Engineers, Warrendale, PA).

Dixon

J. C.

Tires, suspension and handling, 1996 (Society of Automotive Engineers, Warrendale, PA; Arnold, London).

Ellis

J. R.

Vehicle handling dynamics, 1994 (Mechanical Engineering Publications, Bury St Edmunds and London).

Pacejka

H. B.

Tyre and vehicle dynamics, 2002 (Butterworth-Heinemann, Oxford).

Rahnejat

Multibody dynamics: vehicles, machines, and mechanisms, 1998 (Professional Engineering Publications, Bury St Edmunds and London, and Society of Automotive Engineers, Warrendale, PA (Co-publishers)).

Hegazy

Rahnejat

Hussain

Multibody dynamics in full-vehicle handling analysis

Proc. Instn Mech. Engrs, Part K: J. Multi-body Dynamics, 1999, 213, 19–31.

Hegazy

Rahnejat

Hussain

Multibody dynamics in full-vehicle handling analysis under transient manoeuvre

Vehicle Syst. Dyn., 2000, 34, 1–24.

10.

Blundell

Harty

Multibody systems approach to vehicle dynamics, 2004 (Elsevier, Butterworth-Heinemann, Oxford).

11.

Genta

Motor vehicle dynamics: modeling and simulation, 1997 (World Scientific Publishing, Singapore).

12.

Lin

R. C.

Cebon

Cole

D. J.

An investigation of active roll control of heavy road vehicles. In Proceedings of 13th IAVSD Symposium, Chengdu, China, 1993.

13.

Sampson

Active roll control of articulated heavy vehicles. PhD Thesis, Engineering Department, University of Cambridge, Cambridge.

14.

Aurell

The influence of warp compliance on the handling and stability of heavy commercial vehicles

International Symposium on Advanced vehicle control 2002, Tokyo, 2002 (Society of Automotive Engineers of Japan, Japan).

15.

ADAMS (Automatic dynamic analysis of multibody systems) manual version 12, MSC.NASTRAN, 2003.

16.

Pacejka

H. B.

Bakker

The magic formula tyre model, tyre models for vehicle dynamic analysis In Proceedings of the First International Colloquium on Tyre models for vehicle dynamic analysis (Ed. Pacejka

H. B.

) 1993, pp. 1–18 (Swets and Zeitlinger, Lisse).

17.

Da Cunha

Handling analysis of a three-axle intercity bus. 16th European ADAMS User Conference 2001, Berchtesgaden, 2001 (MSC Software, Germany).

18.

Society of Automotive Engineers.

Steady-state circular test procedure for trucks and buses, 1998 (Society of Automotive Engineers, Warrendale, PA).

19.

Ross

C. F.

Electronic braking systems: An aid to vehicle stability. In

Braking of road vehicle, 2004 (University of Bradford, UK) ISBN 1851432175.

20.

Gordon

Multibody dynamic lecture notes, 2000. MSc course in Automotive Engineering (Department of Aeronautical and Automotive Engineering, University of Loughborough, UK).