The paper describes a noise, vibration and harshness (NVH) phenomenon caused by impact of meshing gear teeth pairs, resulting in structural wave propagation and elastoacoustic coupling in the driveline system, referred to in industry as clonk. The numerical investigation combines multi-body dynamics analysis with flexible body oscillation behaviour predicted by finite element analysis (FEA) techniques. Particular attention is paid to local non-linearities such as the varying stiffness of meshing gear teeth and their normal backlash. The spectrum of vibration of lightly damped hollow driveshaft tubes shows good conformity with experimental results.
ArrundaleD.HussainK.RahnejatH.MendayM. T.Acoustic response of driveline pieces under impacting loads (clonk). Proc. 31st ISATA, 1998, 319–331.
2.
BiermannJ. W.HagerodtB.Investigation into the clonk phenomenon in vehicle transmission-measurement, modelling and simulationProc. Instn Mech. Engrs, Part K: J. Multi-body Dynamics, 1999, 213 (1), 53–60.
3.
MendayM.RahnejatH.EbrahimiM.Clonk: An onomatopoeic response in torsional impact of automotive drivelinesProc. Instn Mech. Engrs, Part D: J. Automobile Engineering, 1999, 213, 349–357.
4.
VafaeiS.MendayM. T.RahnejatH.Transient high-frequency elasto-acoustic response of a vehicular drivetrain to sudden throttle demandProc. Instn Mech. Engrs, Part K: J. Multi-body Dynamics, 2001, 215, 35–52.
5.
FothergilD. J.SwierstraN.The application of nonlinear displacements modelling techniques to an automotive driveline for the investigation of shunt. VDI Ber., 1992, (1007), 163–179.
6.
HawthornJ.A mathematical investigation of driveabilityInstn Mech. Engrs, report C420/003, 1995.
7.
RookeG.ChanE. A.CrossleyP. R.Computer modelling of a vehicle powertrain for driveability development. Institution of Mechanical Engineers Conference Transactions, 1995, C462/31/035, pp. 1–9.
8.
FarshindiafarA.EbrahimiM.RahnejatH.MendayM. T.High frequency torsional, vibration of vehicular driveline systems in clonkInt. J. Veh. Des., 2002, 9, 127–149.
9.
KrenzR.Vehicle response to throttle tip in/tip out. SAE paper 850967, 1985.
10.
ToblerW.TsangeridesM.Dynamic behaviour of a torque converter with centrifugal bypass clutch. SAE paper 850461, 1985.
11.
PetriH.HeldingfeldD.The hydraulic torsion damper-a new concept for vibration damping in powertrains. SAE paper 892447, 1989.
12.
KellyP.MendayM.RahnejatH.EbrahimiM.Powertrain refinement: A combined experimental and multi-body dynamics analysis approach8th Aachener Kolloquium,1999.
13.
FahyF. J.Sound and Structural Vibration: Radiation, Transmission and Response, 1985 (Academic Press, London).
14.
NortonM. P.Fundamentals of Noise and Vibration Analysis for Engineers, 1989 (Cambridge University Press).
15.
Adams/Solver Reference Manual, Version 12.0, 2002 (Mechanical Dynamics Inc., Ann Arbor, Michigan).
16.
PatranlNastran Reference Manual, Version 2001, 1998 (MSC Software, Los Angeles, USA).
17.
CraigR. R.JrStructural Dynamics-An Introduction to Computer Methods, 1981 (John Wiley, New York).
18.
ZhangJ. J.EsatI. I.ShiY. H.Load analysis with varying mesh stiffnessComputers and Struct., 1999, 70, 273–280.
19.
ChoiM.DavidJ. W.Mesh stiffness and transmission error of spur and helical gears. SAE paper 901764, 1990.
20.
ChenY. C.TsayC. B.Stress analysis of helical gear set with localized bearing contactFinite Elements in Analysis and Des., 2002, 38, 707–723.
21.
RahnejatH.Influence of vibration on oil film in concentrated contacts. Doctoral thesis, Imperial College of Science and Technology, University of London, 1984.
