Evaluation of water turbine hydrodynamic thrust bearing performance on the basis of thermoelastohydrodynamic calculations and operational data

Abstract

An analysis of thrust bearing performance was taken up in order to assess the possibility of bearing installation in a modernized Kaplan turbine. Apart from analysis of the records of machine operation, thermoelastohydrodynamic calculations were carried out. A bearing design incorporating a mechanism of compensation of thermal deformation was of interest, especially as the machine and its bearings were designed earlier than 1952, while the first analyses of such mechanisms known to the authors were published in the 1960s. Apart from direct analysis of the feasibility of the bearing in new operating conditions, the authors carried out a study of the influence of the two most important design parameters on the bearing performance. Thermoelastohydrodynamic calculations showed that the bearing was surprisingly well designed, especially as it was designed without the aid of contemporary calculation methods and techniques. The main conclusion of the analysis was that the bearing pads can be used without any modifications. In addition, it was recommended that the jacking mechanism be redesigned in order to improve load distribution among the pads and facilitate bearing aligning during assembly. The bearing housing was also redesigned in order to reduce the stresses in the welded joints.

Keywords

hydrodynamic thrust bearings tilting pad thrust bearings thermohydrodynamic calculations assessment of design

Get full access to this article

View all access options for this article.

References

Ettles

Cameron

Thermal and elastic distortions in thrust-bearings. IMechE Lubr. Wear Conv., 1963, paper 7, pp. 60–71.

Raimondi

A. A.

The influence of transverse and longitudinal profile on the load capacity of pivoted bearings. Trans. ASME, 1960, 3 (2), 265–275.

Rohde

S. M.

McAllister

G. T.

On the optimization of fluid film bearings. Proc. R. Soc. (Lond.) A, 1976, 351, 481–497.

Wasilczuk

Influence of operating conditions on optimum film profile of a thrust bearing. In Proceedings of 2nd World Tribology Congress, Vienna, 2001 (CD ROM).

Ettles

C. M.

Size effects in tilting pad thrust bearings. Wear, 1980, 59, 231–245.

Okano

Furukawa

Kawaike

Recent developments in thrust bearings for large-capacity high-speed hydrogenerators. Hitachi Rev., 1979, 28 (4), 189–192.

Kawaike

Okano

Furukawa

Performance of a large thrust bearing with minimized thermal distortion. ASLE Trans., 1977, 22 (2), 125–134.

Kuhn

E. C.

Largest thrust bearings are water cooled. Mech. Transm. Lubr., Power, October 1971, 100–101.

Ettles

C. M.

Some factors affecting the design of spring supported thrust bearings in hydroelectric generators. Trans. ASME, J. Tribology, July 1991, 113, 626–632.

10.

Golebiewski

Report on operation of thrust bearings in Dychow HEPP (in Polish). Unpublished report, Czymanowo, 2001.

11.

Dabrowski

Wasilczuk

Evaluation of Dychów power plant hydrodynamic thrust bearings reliability on the basis of thermohydrodynamic calculations (in Polish). Tribologia, 2002, 157–169.

12.

Shawcross

Dudley

B. R.

The performance of tilting pad thrust bearings. Proc. Instn Mech. Engrs, Part C: J. Mechanical Engineering Science, 1971, C68/71, 105–111.

13.

Dabrowski

Multi support plate spring as a compliant support for thrust bearing pads. PhD dissertation, Faculty of Mechanical Engineering, Tech. Univ. Gdansk, 1997.

14.

Dabrowski

Wasilczuk

On the accuracy of theoretical models of hydrodynamic thrust bearings. In Proceedings of Conference BALKANTRIB 96, Thessaloniki, 1996.

15.

Ettles

C. M.

Anderson

H. G.

Three-dimensional thermoelastic solutions of thrust bearings using code Marmacl. Trans. ASME, J. Tribology, 1991, 113, 405–12.

16.

Hydrodynamische Axial-Gleitlager im stationaren Betrieb. Deutsche Industrie Normen (DIN) 31654, Part 1–3, 1991.

17.

Rayleigh

Lord

Notes on the theory of lubrication. Philosophy Mag., 1918, 35, 1–12.

18.

Prevention of the failures of gearboxes, bearings and oil systems (in French). Allianz Versicherung AG report, 1990.

19.

Bouchoule

Fillon

Frene

Nicolas

Hydrodynamic journal and thrust bearing damage. 4th International Congress MAT-TEC-93 on Improvements of Materials, Paris, 1993, pp. 109–114.