This paper discusses an experimental device used to investigate thermoelasto-hydrodynamic behaviour of connecting rod big-end bearing models. Theoretical results for this device are obtained by calculation with a two-dimensional thermoelastohydrodynamic model. A brief description of both theoretical development and experimental device is presented. After the presentation of measurement results, a comparison with theoretical results is discussed.
GrenteCh.LigierJ. L.ToploskyJ.BonneauD.The consequence of performance increases of automotive engines on the modelling of main and connecting-rod bearings. 27th Leeds—Lyon Symposium on Tribology, 2000, pp. 839–850.
2.
FantinoB.FrêneJ.du ParquetJ.Elastic connecting-rod bearing with a piezoviscous lubricant: Analysis of the steady-state characteristics. Trans. ASME, J. Lubrication Technol., 1979, 101, 190–200.
3.
FantinoB.GodetM.FrêneJ.Dynamic behavior of an elastic connecting-rod bearing theoretical study. Proc. Soc. Automot. Engrs, Studies of Engine Bearings and Lubrication, 1983, S. P. 539, SAE paper 830307, pp. 23–32.
4.
FantinoB.FrêneJ.du ParquetJ.Viscosity effects on the dynamic characteristics of an Elastic Engine Bearing. SAE/SP-640 Engine Lubrication, SAE paper 852074, 1985.
GoenkaP. K.An optimum short bearing theory for the elastohydrodynamic solutions of journal bearings. Trans. ASME, 1986, 108, 294.
7.
BonneauD.GuinesD.EHD analysis, including structural inertia effects and a mass-conserving cavitation model. Trans. ASME, J. Lubrication Technol., 1995, 117, 540–547.
8.
BodeoS.BookerJ. F.Finite element analysis of elastic engine bearing lubrication: Application. Rev. Eur. Éléments Finis, 2001, 10 (6–7), 725–740.
9.
BoedoS.BookerJ. F.Surface roughness and structural inertia in a mode-based mass-conserving elastohydrodynamic lubrication model. Trans. ASME, J. Tribology, 1997, 119, 449–455.
10.
UshijimaK.MotekiK.GotoT.AoyamaD.A study on bearing performance focusing on the viscosity—pressure characteristic of the lubricant and housing stiffness. SAE paper 961144, 1996.
11.
PiffeteauS.SouchetD.BonneauD.Influence of thermal and elastic deformations on connecting-rod big end bearing lubrication under dynamic loading. Trans. ASME, J. Tribology, 1999, 122, 181.
12.
SouchetD.PiffeteauS.BonneauD.Lubrification des paliers de tête de bielle de moteurs thermiques—modelisation thermoélastohydrodynamique bidimensionnelle. 19th International Conference on Science and Technology, Hanoi, Vietnam, 12–13 October 2001 (Hanoi Polytechnic Institute).
13.
SouchetD.PiffeteauS.Approche par la MEF de la lubrification thermoélastohydrodynamique des paliers de tête de bielle. Rev. Eur. Éléments Finis, 2001, 10 (6–7), 815, 847.
14.
KimB. J.KimK. W.Thermo-elastohydrodynamic analysis of connecting-rod bearing in internal combustion engine. Trans. ASME, 2001, 123.
15.
MasudaT.UshijimaK.HamaiK.A measurement of oil film pressure distribution in connecting-rod bearing with test rig. Tribology Trans., 1992, 35 (1), 71–76.
16.
BatesT. W.FantinoB.FrêneJ.Oil film thickness in a connecting-rod bearing: Comparison between calculation and experiment by total capacitance method. SAE paper 880679, 1988.
17.
TsuyoshiM.KenshiU.KyugoH.A measurement of oil film pressure distribution in connecting-rod bearing with test rig. Tribology Trans., 1992, 35 (1), 71–76.
18.
ChoiJ. K.LeeJ. H.HanD. C.Oil film thickness in engine main bearings: Comparison between calculation and experiment by total capacitance method. SAE paper 922345, 1992, pp. 147–159.
19.
ChoM. R.HanD. C.ChoiJ. K.Oil film thickness in engine connecting-rod bearing with consideration of thermal effects: Comparison between theory and experiment. J. Tribology, 1999, 121, 901.
20.
MoreauH.MaspeyrotP.Chomat-DelalexA. M.BonneauD.FrêneJ.Dynamic behaviour of elastic engine main bearings: Theory and measurements. Proc. Instn Mech. Engrs, Part J: J. Engineering Tribology, 2001, 216, 179–193.
21.
OptasanuV.BonneauD.Lubrification elastohydro-dynamique des paliers de tête de bielle—etude expérimentale utilisant des modéles photoélastiques. Colloque PhotoMécanique Poitiers, 2001, pp. 255, 262.
22.
RhodeS. M.LiD. F.A generalised short bearing theory. Trans. ASME, J. Tribology, 2000, 102 (3), 278–282.
23.
BonneauD.HajjamM.Modrélisation de la rupture et de la reformation des films lubrifiants dans les contacts élastohydrodynamiques. Rev. Eur. Éléments Finis, 2001, 10 (6–7), 679, 704.
24.
SuttonM. A.WolatersW. J.PetersW. H.RansonW. F.McNeilS. R.Determination of displacements using an improved digital correlation method. Computer Vision, 1983, 133–139.
