The paper presents a transient analysis technique for line contact elastohydrodynamic lubrication problems using coupled elastic and hydrodynamic equations. Full coupling is made possible by use of a novel differential deflection formulation. The lubricant is treated as non-Newtonian with a non-linear Eyring-type relationship between shear stress and shear strain rate. Results are presented for moving rough surfaces where the roughness data are taken from profilometer traces of run-in ground surfaces. A complete range of slide-roll ratios has been considered and results are shown for one rough surface in rolling/sliding motion against a smooth surface with extremely low lambda ratios (ratio of minimum film clearance to r. m.s. roughness). Results are also shown for two rough surfaces in contact under severe thin-film high-roughness conditions.
GrubinA. N.Fundamentals of the hydrodynamic theory of lubrication of heavily loaded cylindrical surfaces. Book 30, 1949 (Central Scientific Research Institute for Technology and Engineering, Moscow) (DSIR Translation 337).
BairS.WinerW. O.A rheological model for elastohydrodynamic contacts based on primary laboratory dataTrans. ASME, J. Lubric. Technol., 1979, 101, 258–265.
4.
JohnsonK. L.TevaarwerkJ. L.The shear behaviour of elastohydrodynamic oil filmsProc. R. Soc. Lond. A, 1977, 356, 215–236.
5.
GogliaP. R.CusanoC.ConryT. F.The effects of surface irregularities on the elastohydrodynamic lubrication of sliding line contacts. Part I: Single irregularities; Part II: Wavy surfacesTrans. ASME, J. Tribology, 1984, 106, 104–112, 113–119.
6.
LubrechtA. A.Ten NapelW. E.BosmaR.The influence of longitudinal and transverse roughness on the elastohydrodynamic lubrication of circular contactsTrans. ASME, J. Tribology, 1988, 110, 421–426.
7.
KwehC. C.EvansH. P.SnidleR. W.Micro-elastohydrodynamic lubrication of an elliptical contact with transverse and three-dimensional sinusoidal roughnessTrans. ASME, J. Tribology, 1989, 111, 577–584.
8.
KwehC. C.PatchingM. J.EvansH. P.SnidleR. W.Simulation of elastohydrodynamic contacts between rough surfacesTrans. ASME, J. Tribology, 1992, 114, 412–419.
9.
ChangL.WebsterM. N.A study of elastohydrodynamic lubrication of rough surfacesTrans. ASME, J. Tribology, 1991, 113, 110–115.
10.
VennerC. H.LubrechtA. A.Transient analysis of surface features in an EHL line contact in the case of slidingTrans. ASME, J. Tribology, 1994, 116, 186–193.
11.
GreenwoodJ. A.Morales-EspejelG. E.The behaviour of transverse roughness in EHL contactsProc. Instn Mech. Engrs, Part J, Journal of Engineering Tribology, 1994, 208 (J2), 121–132.
12.
ChangL.WebsterM. N.JacksonA.On the pressure rippling and roughness deformation in elastohydrodynamic lubrication of rough surfacesTrans. ASME, J. Tribology, 1993, 115, 439–444.
13.
ChangL.ZhaoW.Fundamental differences between Newtonian and non-Newtonian micro-EHL resultsTrans. ASME, J. Tribology, 1995, 117, 29–35.
14.
VennerC. H.Ten NapelW. E.Surface roughness effects in an EHL line contactTrans ASME, J. Tribology, 1992, 114, 616–622.
15.
AiX.ChengH. S.A transient EHL analysis for line contacts with measured surface roughness using multigrid techniqueTrans. ASME, J. Tribology, 1994, 116, 549–556.
16.
VennerC. H.LubrechtA. A.Numerical analysis of the influence of waviness on the film thickness of a circular EHL contactTrans. ASME, J. Tribology, 1996, 118, 153–161.
17.
XuG.SadeghiF.Thermal EHL analysis of circular contacts with measured surface roughnessTrans. ASME, J. Tribology, 1995, 117, 473–483.
18.
OkamuraH.A contribution to the numerical analysis of isothermal elastohydrodynamic lubrication. InTribology of Reciprocating Engines, Proceedings of the 9th Leeds-Lyon Symposium on Tribology, Leeds, 1982, 1983, pp. 313–320 (Butterworth, London).
19.
HoupertL. G.HamrockB. J.Fast approach for calculating film thicknesses and pressures in elastohydrodynamically lubricated contacts at high loadsTrans. ASME, J. Tribology, 1986, 108, 411–420.
20.
EvansH. P.HughesT. G.Evaluation of deflection in semi-infinite bodies by a differential methodProc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 2000, 214 (C4), 563–584.
21.
HughesT. G.ElcoateC. D.EvansH. P.Coupled solution of the elastohydrodynamic line contact problem using a differential deflection methodProc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 2000, 214 (C4), 585–598.
22.
ConryT. F.WangS.CusanoC.A Reynolds-Eyring equation for elastohydrodynamic lubrication in line contactsTrans. ASME, J. Tribology, 1987, 109, 648–654.
23.
SharifK. J.MorrisS. J.EvansH. P.SnidleR. W.Comparison of non-Newtonian EHL models in high sliding applications.In Proceedings of the 27th Leeds-Lyon Symposium on Tribology, Lyon, 2000, 2001 (Elsevier, Amsterdam).
24.
RoelandsC. J. A.Correlational aspects of the viscosity-temperature-pressure relationship of lubricating oils. Druk. URB, Grönigen, 1966.
25.
HughesT. G.ElcoateC. D.EvansH. P.A novel method for integrating first and second order differential equations in elastohydrodynamic lubrication for the solution of smooth isothermal, line contact problemsInt. J. Numer. Meth. Engng, 1999, 44, 1099–1113.
26.
ElcoateC. D.Coupled solution methods for the elastohydrodynamic problem. PhD thesis, University of Wales, 1996.
27.
BrittonR. D.ElcoateC. D.AlanouM. P.EvansH. P.SnidleR. W.Effect of surface finish on gear tooth frictionTrans. ASME, J. Tribology, 2000, 122, 354–360.
28.
PatchingM. J.The effect of surface roughness on the micro-elastohydrodynamic lubrication and scuffing performance of aerospace gear tooth contacts. PhD thesis, University of Wales, 1994.
29.
ElcoateC. D.EvansH. P.HughesT. G.SnidleR. W.Fully coupled elastohydrodynamic solution techniques for the analysis of real rough line contacts using finite element and finite difference models. InLubrication at the Frontier, Proceedings of the 25th Leeds-Lyon Symposium on Tribology, Lyon, 1998, 1999, pp. 163–174 (Elsevier, Amsterdam).
30.
HolmesM.A fully coupled method for solving the Newtonian steady state isothermal elastohydrodynamic point contact problemProc. South Wales Inst. Engrs, 2000, 108.
