Film thickness predictions for elastohydrodynamic elliptical contacts over a wide range of radius ratios with consideration of side starvation

Abstract

The paper presents numerical solutions obtained for a wide range of elliptical elastohydrodynamic lubrication (EHL) problems. The conditions considered encompass relative principal radii of curvature ratios from 20:1 with entrainment in the minor axis direction, to 50:1 with entrainment in the major axis direction. The problems considered derive from investigations of practical machine elements where the width of contact (perpendicular to entrainment) is limited by the extent of the metal surfaces on either side. Two sets of results have been obtained: one with the width of the lubricated contact approximately twice that of the Hertzian dry contact, and the other where the ratio of these widths is 1.2. Taken as a whole the results present a complete range of conditions obtained using the same numerical model throughout. The film thickness predictions are compared with those given by well-known published formulae and design charts.

Keywords

elastohydrodynamic elliptical contacts side starvation

Get full access to this article

View all access options for this article.

References

Kapitza

P. L.

Hydrodynamic theory of lubrication during rolling

Zh. Tekh. Fiziki, 1955, 25, 747–762.

Archard

J. F.

Cowking

E. W.

Elastohydrodynamic lubrication at point contacts

Proc. Instn Mech. Engrs, 1965-6, 180 (3b), 47–56.

Ranger

A. P.

Ettles

C. M.M.

Cameron

The solution of the point contact elastohydrodynamic problem

Proc. R. Soc. Lond. A, 1975, 346, 227–244.

Hamrock

B. J.

Dowson

Isothermal elasto-hydrodynamic lubrication of point contacts, Part 1: Theoretical formulation

Trans. ASME, J. Lubric. Technol., 1976, 98, 223–229.

Evans

H. P.

Snidle

R. W.

The elastohydrodynamic lubrication of point contacts at heavy loads

Proc. R. Soc. Lond. A, 1982, 382, 183–199.

Chittenden

R. J.

Dowson

Dunn

J. F.

Taylor

C. M.

A theoretical analysis of the isothermal elastohydrodynamic lubrication of concentrated contacts

Proc. R. Soc. Lond. A, 397, 271–294.

ESDU Film thickness in lubricated Hertzian contacts. Part 2: point contacts. Data Item 89045, ESDU, London, 1989.

de Ling

Barragan F. d. M.

Evans

H. P.

Snidle

R. W.

Thrust cone lubrication. Part 2: Elastohydrodynamic analysis of crowned rims

Proc. Instn Mech. Engrs, Part J, Journal of Engineering Tribology, 1996, 210 (J2), 97–105.

Moes

Bosma

Film thickness and traction in EHL point contacts. In Proceedings of the Symposium on

Elastohydrodynamic Lubrication, 1972, pp. 149–152 (Institution of Mechanical Engineers, London).

10.

Newall

J. P.

Elastohydrodynamic lubrication of elliptical point contacts. PhD thesis, University of Wales, 1995.

11.

Kweh

C. C.

Evans

H. P.

Snidle

R. W.

Elastohydrodynamic lubrication of heavily loaded circular contacts

Proc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 1989, 203 (C2), 133–148.

12.

Hooke

C. J.

Minimum film thickness in lubricated point contacts operating in the elastic piezoviscous regime

Proc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 1988, 202 (C2), 73–84.

13.

Greenwood

J. A.

Film thickness in circular elastohydrodynamic contacts

Proc. Instn Mech. Engrs, Part C, Journal of Mechanical Engineering Science, 1988, 202 (C1), 11–17.