The asymmetric influence of the volute on the flow in a transonic, high-pressure ratio centrifugal compressor at off-design conditions was investigated. Fully three-dimensional viscous steady-state computational fluid dynamics (CFD) was applied to simulate the flow in a 4.2:1 design pressure ratio compressor for automotive application. Computed performance characteristics are presented for low- and high-pressure ratio operating conditions, with and without an overhung volute. The volute was found to severely harm aerodynamic stability of the investigated compressor when operating at lower than design mass flow. The relative narrowing effect of the volute on compressor map width increases with pressure ratio up to a 42 per cent drop in stable flow range at design speed. The inter-passage variations in performance quantities and the influence of the volute tongue region are discussed in detail. The circumferential variations of incidence angle correlate with rotational speed, which, in combination with the higher sensitivity to incidence angle at transonic inflow conditions, seems to deteriorates stability when transonic inflow conditions are reached.
HayamiH.ChunillH.Research and development of a transonic turbo compressorTurbomachinery and heat transfer1997New YorkMarcel Dekker Inc.63–82
2.
AyderE.den BraembusscheR. V.Experimental study of the swirling flow in the internal volute of a centrifugal compressor ASME paper no. 91-GT-7, 1991
3.
AyderE.Experimental and numerical analysis of the flow in centrifugal compressor and pump volutes PhD Thesis, Universiteit Gent and VKI, 1993
4.
AyderE.den BraembusscheR. V.BraszJ. J.Experimental and theoretical analysis of the flow in a centrifugal compressor voluteJ. Turbomach.1993115582–589
5.
SorokesJ.BorerC.KochJ.Investigation of the circumferential static pressure non-uniformity caused by a centrifugal compressor discharge volute ASME paper no. 98-GT-326, 1998
6.
HagelsteinD.den BraembusscheR. V.KeiperR.RautenbergM.Experimental investigation of the circumferential pressure distortion in centrifugal compressor stages ASME paper no. 97-GT-50, 1997
7.
Den BraembusscheR. V.HaendelB.Experimental and theoretical study of the swirling flow in centrifugal compressor volutesJ. Turbomach.199011238–43
8.
Den BraembusscheR. V.AyderE.HagelsteinD.RautenbergM.KeiperR.Improved model for the design and analysis of centrifugal compressor volutesJ. Turbomach.1999121619–625
9.
AyderE.Numerical analysis of the three-dimensional swirling flow in centrifugal compressor volutesJ. Turbomach.1994116462–467
10.
FlathersM.BacheG.Aerodynamically induced radial forces in a centrifugal gas compressor – part 2: Computational investigation ASME paper no. 96-GT-352, 1996
11.
HillewaertK.den BraembusscheR. V.Numerical simulation of impeller-volute interaction in centrifugal compressorJ. Turbomach.1999121603–608
12.
GuF.EngedaA.CaveM.Di LibertiJ.-L.A numerical investigation on the volute/diffuser interaction due to the axial distortion at the impeller exitJ. Fluids Eng.20011233475–483
13.
GuF.EngedaA.A numerical investigation on the volute/impeller steady-state interaction due to circumferential distortion ASME paper no. 2001-GT-0328, 2001
14.
SorokesJ.KochJ.The influence of low solidity vaned diffusers on the static pressure non-uniformity caused by a centrifugal compressor discharge volute ASME paper no. 2000-GT-0454, 2000
15.
SteglichT.KitzingerJ.SeumeJ. R.den BraembusscheR. V.PrinsierJ.Improved diffuser/volute combinations for centrifugal compressors ASME paper no. GT2005-68894, 2005
16.
PanD.WhitfieldA.WilsonM.Design considerations for the volutes of centrifugal fans and compressorsProc. IMechE, Part C: J. Mechanical Engineering Science1999213401–410 DOI: 10.1243/0954406991522356
17.
ReunanenA.Experimental and numerical analysis of different volutes in a centrifugal compressor PhD Thesis, Lappeenranta University of Technology, Lappeenranta, 2001
18.
HassanA. S.Influence of the volute design parameters on the performance of a centrifugal compressor of an aircraft turbochargerProc. IMechE, Part A: J. Power and Energy2006221695–704 DOI: 10.1243/09576509JPE436
19.
DaiY.EngedaA.CaveM.Di LibertiJ.-L.Numerical study and experimental validation of the performance of two different volutes with the same compressor impellerProc. IMechE, Part B: J. Engineering Manufacture2009223157–166 DOI:10.1243/09576509JPE676
20.
DaiY.EngedaA.CaveM.Di LibertiJ.-L.A flow field study of the interaction between a centrifugal compressor impeller and two different volutesProc. IMechE, Part A: J. Power and Energy2010224345–356 DOI: 10.1243/09544062JMES1522
21.
XuC.AmanoR.Eliminating static pressure distortion by a large cut back tongue volute ASME paper no. GT2006-90001, 2006
22.
XuC.MuellerM.Development and design of a centrifugal compressor voluteInt. J. Rotat. Mach.20053190–196
23.
JamesonA.BakerT.Solutions of the Euler equations for complex configurations AIAA paper no. 83-1929, 1983
24.
JamesonA.SchmidtW.TurkelE.Numerical solutions of the Euler equations by finite volume methods using Runge–Kutta time stepping schemes AIAA paper no. 81-1259, 1981
25.
MartinelliL.Calculations of viscous flows with a multigrid method PhD Thesis, Princeton University, 1987
26.
VatsaV.WedanB.Development of an efficient multigrid code for 3-D Navier-stokes equations AIAA paper no. 89-1791, 1989
27.
SpalartP.AllmarasS.A one equation turbulence model for aerodynamic flows AIAA paper no. 92-0439, 1992
28.
AshfordG.PowellK.An unstructured grid generation and adaptative solution technique for high-Reynolds number compressible flow Lecture Series 1996-06, VKI (Von Karman Institute), 1996
29.
NUMECA International. NUMECA FINE/Turbo User Manual 7.1, 2006 (NUMECA International, Belgium). Available from www.numeca.com
30.
FatsisA.PierretS.den BraembusscheR. V.Three-dimensional unsteady flow and forces in centrifugal impellers with circumferential distortion of the outlet static pressureJ. Turbomach.199711994–102
31.
HunzikerR.DickmannH.-P.EmmrichR.Numerical and experimental investigation of a centrifugal compressor with an inducer casing bleed systemProc. IMechE, Part A: J. Power and Energy2001215783–791 DOI: 10.1243/0957650011538910
32.
YamaguchiS.YamaguchiH.GotoS.NakaoH.NakamuraF.The development of effective casing treatment for turbocharger compressors In Proceedings of the 7th International Conference on Turbochargers and turbocharging, IMechE C602/008/2002 2002
33.
KrainH.HoffmannB.RohneK.-H.EisenlohrG.RichterF.-A.Improved high pressure ratio centrifugal compressor ASME paper no. GT2007-27100, 2007
34.
KrainH.KarpinskiG.BeversdorffM.Flow analysis in a transonic centrifugal compressor rotor using 3-component laser velocimetry ASME paper no. 2001-GT-0315, 2001
35.
GuoG.ZhangY.XuJ.ZhengX.ZhugeW.Numerical simulation of a transonic centrifugal compressor blades tip clearance flow of vehicle turbocharger ASME paper no. GT2008-50957, 2008
36.
XuC.AmanoR. S.Computational analysis of scroll tongue shapes to compressor performance by using different turbulence models ASME paper no. GT2007-28224, 2007
37.
KangS.Numerical investigation of a high speed centrifugal compressor impeller ASME paper no. GT2005-68092, 2005
38.
IbarakiS.FurukawaM.IwakiriK.TakahashiK.Vortical flow structure and loss generation process in a transonic centrifugal compressor impeller ASME paper no. GT2007-27791, 2007
39.
HazbyH.XuL.Role of tip leakage in stall of transonic centrifugal compressor ASME paper no. GT2009-59372, 2009
