The present experimental investigation is aimed at studying the effect of tip injection on the performance and flow characteristics in the tip region of an axial flow fan under uniform and distorted inflow conditions. A detailed parametric study was carried out by varying injection parameters such as pitch and skew angles, jet-to-free-stream velocity ratio, number of injectors, and the axial location of the injectors. The configuration with six injectors, jet-to-free-stream velocity ratio of 3.5, 0° pitch angle, and injector skew angle of-15° (in an orientation opposing the direction of rotor rotation) resulted in the highest stall margin improvement of ∼9.4 per cent. This study was further extended to determine the effects of circumferential and combined circumferential and radial inflow distortion on fan performance and the effectiveness of tip injection under these conditions. A preliminary study of the effect of pulsed injection was also carried out at different pulsing frequencies in order to optimize injection flowrates. Interestingly, pulsed injection resulted in less stall margin improvement when compared with continuous injection. These results have been supported by flow behaviour studies carried out in the tip region using a seven-hole probe. A qualitative study was carried out using unsteady pressure transducers, and it revealed that the trailing edge of the distortion screen acts as a source of disturbances.
LiawD. C.AbedE. H.Active control of compressor stall inception: A bifurcation-theoretic approach. Automatica, 1996, 32, 109–115.
2.
GuG.SparksA.BandaS.An overview of rotating stall and surge control for axial flow compressors. IEEE Trans. Control Syst. TechnoL, 1999, 7, 639–647.
3.
MooreF. K.A theory of rotating stall of multistage axial compressors: Parts I, II and III. Trans. ASME J. Eng. Gas Turbines Power, 1984, 106, 313–336.
4.
MooreF. K.GreitzerE. M.A theory of post-stall transients in axial compression systems, part I: Development of equations. Trans. ASME J. Eng. Gas Turbines Power, 1986, 108, 69–76.
5.
MooreF. K.GreitzerE. M.A theory of post-stall transients in axial compression systems, part II: Application. Trans. ASME J. Eng. Gas Turbines Power, 1986, 108, 231–239.
6.
WilliamsJ. F. E.HarperM. F. L.AllwrightD. J.Active stabilization of compressor instability and surge in a working engine. Trans. ASME J. Turbomach., 1993, 115, 68–75.
7.
VoH. D.TanC. S.GreitzerE. M.Criteria for spike initiated rotating stall. In the ASME Turbo Expo 2005: Power for Land, Sea, and Air, Reno, Nevada, USA, 6-9 June 2005.
8.
BaeJ. W.BreuerK. S.TanC. S.Active control of tip clearance flow in axial compressors. Trans. ASME J. Turbomach., 2005, 127, 352–362.
9.
CopenhaverW. W.OkiishiT.Rotating stall performance and recoverability of a high-speed 10-stage axial flow compressor. J. Propuls. Power, 1993, 9, 281–291.
10.
HynesJ. M.HendricksG. J.EpsteinA. H.Active stabilization of rotating stall in a three-stage axial compressor. Trans. ASMEJ. Turbomach., 1994, 116, 226–239.
11.
TryfonidisM.EtcheversO.PaduanoJ. D.EpsteinA. H.HendricksG. J.Prestall behavior of several high-speed compressors. Trans. ASME J. Turbomach., 1995, 117, 62–80.
12.
JagerB. D.Rotating stall and surge control: A survey. In Proceedings of the 34th Conference on Decision and Control, New Orleans, December 1995.
13.
LinE.LiM.ChenJ.Long-to-short length-scale transition: A stall inception phenomenon in an axial compressor with inlet distortion. Trans. ASME J. Turbomach., 2006, 128, 130–140.
14.
DavisM.HaleA.BealeD.An argument for enhancement of the current inlet distortion ground test practice for aircraft gas turbine engines. Trans. ASME J. Turbomach., 2002, 124, 235–241.
15.
SchmidN. R.LeinhosD. C.FottnerL.Steady performance measurements of a turbofan engine with inlet distortions containing co- and counter-rotating swirl from an intake diffuser for hypersonic flight. Trans. ASME J. Turbomach., 2001, 123, 379–385.
16.
PazurW.FottnerL.The influence of inlet swirl distortions on the performance of a jet propulsion two-stage axial compressor. Trans. ASMEJ. Turbomach., 1991, 113, 233–240.
17.
SchalkwykC. M. V.PaduanoJ. D.GreitzerE. M.EpsteinA. H.Active stabilization of axial compressors with circumferential inlet distortion. Trans. ASMEJ. Turbomach., 1998, 120, 431–439.
18.
CampT. R.DayI. J.A study of spike and modal stall phenomena in a low speed axial compressor. Trans. ASMEJ. Turbomach., 1998, 120, 393–401.
19.
DayI. J.BreuerT.EscuretJ.CherrettM.WilsonA.Stall inception and the prospects for active control in four high speed compressors. Trans. ASME J. Turbomach., 1999, 121, 18–27.
20.
GyslingD. L.GreitzerE. M.Dynamic control of rotating stall in axial flow compressors using aerome-chanicalfeedback. Trans. ASMEJ. Turbomach., 1995, 117, 307–319.
21.
SuderK. L.HathwayM. D.ThorpS. A.StrazisarA. J.BrightM. B.Compressor stability enhancement using discrete tip injection. Trans. ASMEJ. Turbomach., 2001, 123, 14–23.
22.
NieC.XuG.ChengX.ChenJ.Micro air injection and its unsteady response in a low-speed axial compressor. Trans. ASME J. Turbomach., 2002, 124, 572–579.
23.
LuX.ChuW.ZhuJ.TongZ.Numerical and experimental investigations of steady micro-tip injection on a subsonic axial-flow compressor rotor. Int.J. Rotat. Mach., 2006, 2006, 1–11.
24.
LeinhosD.C.SchmidN. R.FottnerL.The influence of transient inlet distortions on the instability inception of a low pressure compressor in a turbo-fan engine. Trans. ASME J. Turbomach., 2001, 123, 1–8.
25.
LeinhosD. C.ScheidlerS. G.FottnerL.Experiments in active stall control of a twin-spool turbofan engine. In Proceedings of the ASME Turbo Expo-2002, Amsterdam, The Netherlands, 3-6 June 2002.
26.
VoH. D.Active suppression of rotating stall inception with distributed jet actuation. Int. J. Rotat. Mach., 2007, 2007, 1–15.
27.
SpakovszkyZ. S.WeiglH. J.PaduanoJ. D.SchalkwykC. M.SuderK. L.BrightM. M.Rotating stall control in a high-speed stage with inlet distortion: Part I -radial distortion. Trans. ASMEJ. Turbomach., 1999, 121510–516.
28.
SpakovszkyZ. S.SchalkwykC. M.WeiglH. J.PaduanoJ. D.SuderK. L.BrightM. M.Rotating stall control in a high-speed stage with inlet distortion: Part II- circumferential distortion. Trans. ASME J. Turbomach., 1999, 121, 517–524.
29.
WeiglH. J.PaduanoJ. D.FrenchetteL. G.EpsteinA. H.GreitzerE. M.BrightM. M.StrazisarA. J.Active stabilization of rotating stall and surge in a transonic single-stage axial compressor. Trans. ASME J. Turbomach., 1998, 120, 625–636.
30.
BeheshtiB. H.FarhaniehB.GhorbanianK.TeixeiraJ. A.IveyP. C.Performance enhancement in transonic axial compressors using blade tip injection coupled with casing treatment. Proc. IMechE, Part A: J. Power and Energy, 2005, 219, 321–331.
31.
ScheidlerS. G.MundtC.Active stability control of the compression system in a twin spool turbofan engine by air-injection. In the tenth International Symposium onTransport Phenomena and Dynamics of Rotating Machinery, Honolulu, Hawaii, 7-11 March 2004.
32.
RoyB.ChouhanM.KaundinyaK. V.Experimental study of boundary layer control through tip injection on straight and swept compressor blades. In the ASME Turbo Expo 2005: Power for Land, Sea, and Air, Reno, Nevada, USA, 6-9 June 2005.
33.
ReddyV. S. R. K.SalunkheP. B.PradeepA. M.Experimental investigation of rotating stall control in a single stage axial flow compressor. In Proceedings of the International Gas Turbine Congress, Tokyo, Japan, 2-7 December 2007.
TeolisC.GentD.KimC.TeolisA.PaduanoJ.BrightM.Eddy current sensor signal processing for stall detection. IEEEAC paper-1255, 2004, pp. 1–17.
36.
CulleyD. E.BrightM. M.PrahstP. S.StrazisarA. J.Active flow separation control of a stator vane using embedded injection in a multistage compressor experiment. Trans. ASMEJ. Turbomach., 2004, 126, 24–34.
MoffatR. J.Using uncertainty analysis in the planning of an experiment. Trans. ASMEJ. Fluids Eng., 1985, 107, 173–180.
39.
HolmanJ. P.Experimental methods for engineers, 1966, International Student Edition (McGraw-Hill Book Company, Tokyo).
40.
StrazisarA. J.BrightM. M.ThorpS.CulleyD. E.SuderK. L.Compressor stall control through endwall recirculation. In the ASME Turbo Expo: Power for Land, Sea, and Air, Vienna, Austria, 14-17 June 2004.
41.
AdamczykJ. J.CelestinaM. L.GreitzerE. M.The role of tip clearance in high speed fan stall. Trans. ASME J. Turbomach., 1993, 115, 28–39.
42.
HoyingD. A.TanC. S.VoH. D.GreitzerE. M.Role of blade passage flow structures in axial compressor rotating stall inception. Trans. ASME J. Turbomach., 1999, 121, 735–742.
43.
JohariH.RixonG. S.Effect of pulsing on a vortex generator jets. AIAAJ., 2003, 41, 2309–2315.
