The influence of tibial tray design on the wear of fixed-bearing total knee replacements

Abstract

Debris-induced osteolysis due to surface wear is a potential long-term problem in total knee replacements (TKRs). Wear between the tibial tray and ultra-high molecular weight polyethylene insert is thought to contribute to the wear. This study investigated the influence of tibial tray design on the wear of fixed-bearing TKRs. Specifically, this study investigated the influence of the material's surface finish and design characteristics of the locking mechanism of the tibial tray on the wear in fixed-bearing knees for both cruciate-retaining (CR) and posterior-stabilized designs. A new fixed-bearing tibial tray design using Co—Cr and with an improved locking mechanism significantly reduced polyethylene wear from 22.8 ± 6.0 mm³ per 10⁶ cycles to 15.9 ± 2.9 mm³ per 10⁶ cycles compared with a previous titanium alloy tray with a CR design. The wear rates were similar to those of a fixed-bearing insert clamped into a tibial tray, suggesting that the decrease in wear was due to a reduction in backside wear. There was no significant difference between the wear rates of a cruciate-retaining design and a posterior-stabilized design under the two kinematic conditions tested.

Keywords

total knee replacement polyethylene wear backside wear

Get full access to this article

View all access options for this article.

References

Howling

G. I.

Barnett

P. I.

Tipper

J. L.

Stone

M. H.

Fisher

Ingham

Quantitative characterization of polyethylene debris isolated from periprosthetic tissue in early failure knee implants and early and late failure Charnley hip implants. J. Biomed. Mater. Res., 2001, 58(4), 415–420.

Ingham

Fisher

Biological reactions to wear debris in total joint replacement. Proc. Instn Mech. Engrs Part H: J. Engineering in Medicine, 2000, 214(1), 21–37.

McEwen

H. M. J.

Barnett

P. I.

Bell

C. J.

Farrar

Auger

D. D.

Stone

M. H.

Fisher

The influence of design, materials and kinematics on the in vitro wear of total knee replacements. J. Biomechanics, 2005, 38(2), 357–365.

Wasielewski

R. C.

The causes of insert backside wear in total knee arthroplasty. Clin. Orthop. Related Res., 2002, 404, 232–246.

Conditt

M. A.

Thompson

M. T.

Usrey

M. M.

Ismaily

S. K.

Noble

P. C.

Backside wear of polyethylene tibial inserts: Mechanism and magnitude of material loss. J. Bone Jt Surg. Am., 2005, 87(2), 326–331.

Collier

M. B.

Engh

C. A.

McAuley

J. P.

Ginn

S. D.

Engh

G. A.

Osteolysis after total knee arthroplasty: Influence of tibial baseplate surface finish and sterilization of polyethylene insert - findings at five to ten years postoperatively. J. Bone Jt Surg. Am., 2005, 87(12), 2702–2708.

Rao

A. R.

Engh

G. A.

Collier

M. B.

Lounici

Tibial interface wear in retrieved total knee components and correlations with modular insert motion. J. Bone Jt Surg. Am., 2002, 84(10), 1849–1855.

Barnett

P. I.

McEwen

H. M. J.

Auger

D. D.

Stone

M. H.

Ingham

Fisher

Investigation of wear of knee prostheses in a new displacement/force-controlled simulator. Proc. Instn Mech. Engrs Part H: J. Engineering in Medicine, 2002, 216(1), 51–61.

Lafortune

M. A.

Cavanagh

P. R.

Sommer

H. J.

Kalenak

Three-dimensional kinematics of the human knee during walking. J. Biomechanics, 1992, 25(4), 347–357.

10.

McNulty

Swope

Influence of polyethylene processing, tibial tray surface finish and modular locking mechanism design on in-vitro wear for total knee arthroplasty. In Proceedings of the Annual Meeting of the Orthopaedic Research Society, San Francisco, California, USA, 2004, p. 840 (Orthopaedic Research Society, Rosemont, Illinois).

11.

McNulty

D. E.

Swope

S. W.

DiSilvestro

M. R.

Wear of non-modular and modular total knee tibial components. In 2005 Annual Meeting Transaction of the Society for Biomaterials, Memphis, Tennessee, USA, 2005, p. 80 (Society for Biomaterials, Mt Laurel, New Jersey).