Computational wear models need input data from valid tribological tests. For the wear model of a total hip prosthesis, the contact pressure dependence of wear and friction of ultra-high molecular weight polyethylene (UHMWPE) against polished CoCr in diluted calf serum lubricant was studied, and useful input data produced. Two test devices were designed and built: a heavy load circularly translating pin-on-disc (HL-CTPOD) wear test device and an HL-CTPOD friction measurement device. Both can be used with a wide range of loads. The wear surface diameter of the test pin was kept constant at 9 mm, whereas the load was varied so that the nominal contact pressure ranged from 0.1 to 20 MPa. The wear factor decreased with increasing contact pressure, whereas the coefficient of friction first increased with increasing contact pressure with low pressure values and then decreased. Up to the pressure of 2.0 MPa, the wear mechanisms and wear factors were in good agreement with clinical findings. In the critical range of 2.0-3.5 MPa, the wear mechanisms and wear factors started to differ from clinical ones, and the decrease of the wear factor steepened. The discrepancy became more and more evident as the pressure was gradually increased beyond 3.5 MPa. It appears that the pressure value of 2.0 MPa should not be exceeded in pin-on-disc wear tests that are to reproduce the clinical wear of UHMWPE acetabular cups.
SaikkoV.CaloniusO.Slide track analysis of the relative motion between femoral head and acetabular cup in walking and in hip simulatorsJ. Biomechanics, 2002, 35, 455–464.
2.
CaloniusO.SaikkoV.Slide track analysis of eight contemporary hip simulator designsJ. Biomechanics, 2002, 35, 1439–1450.
3.
CaloniusO.SaikkoV.Force track analysis of contemporary hip simulatorsJ. Biomechanics, 2003, 36, 1719–1726.
4.
SaikkoV.CaloniusO.An improved method of computing the wear factor for total hip prostheses involving the variation of relative motion and contact pressure with location on the bearing surfaceJ. Biomechanics, 2003, 36, 1819–1827.
5.
SaikkoV.CaloniusO.KeränenJ.Effect of slide track shape on the wear of ultra-high molecular weight polyethylene in a pin-on-disc wear simulation of total hip prosthesisJ. Biomed. Mater. Res. (Appl. Biomater.), 2004, 69B, 141–148.
6.
SaikkoV.A multidirectional motion pin-on-disk wear test method for prosthetic joint materialsJ. Biomed. Mater. Res., 1998, 41, 58–64.
7.
MatsubaraK.WatanabeM.The wear properties of high-density polyethylene irradiated by gamma raysWear, 1967, 10, 214–222.
8.
RoseR. M.GoldfarbH. V.EllisE.CrugnolaA. M.On the pressure dependence of the wear of ultrahigh molecular weight polyethyleneWear, 1983, 92, 99–111.
9.
BarbourP. S. M.BartonD. C.FisherJ.The influence of contact stress on the wear of UHMWPE for total replacement hip prosthesesWear, 1995, 181–183, 250–257.
10.
MazzuccoD.SpectorM.Effects of contact area and stress on the volumetric wear of ultrahigh molecular weight polyethyleneWear, 2003, 254, 514–522.
11.
WangA.EssnerA.KleinR.Effect of contact stress on friction and wear of ultra-high molecular weight polyethylene in total hip replacementProc. Instn Mech. Engrs, Part H: J. Engineering in Medicine, 2001, 215 (H2), 133–139.
12.
SaikkoV.AhlroosT.Type of motion and lubricant in wear simulation of polyethylene acetabular cupProc. Instn Mech. Engrs, Part H: J. Engineering in Medicine, 1999, 213 (H4), 301–310.
13.
SaikkoV.A hip wear simulator with 100 test stationsProc. IMechE, Part H: J. Engineering in Medicine, 2005, 219 (H0), 309–318.
14.
SaikkoV.AhlroosT.Wear simulation of UHMWPE for total hip replacement with a multidirectional motion pin-on-disk device: Effects of counterface material, contact area, and lubricantJ. Biomed. Mater. Res., 2000, 49, 147–154.
15.
AtkinsonJ. R.DowsonD.IsaacG. H.WroblewskiB. M.Laboratory wear tests and clinical observations of the penetration of femoral heads into acetabular cups in total replacement hip joints II: A microscopical study of the surfaces of Charnley polyethylene acetabular socketsWear, 1985, 104, 217–224.
16.
AtkinsonJ. R.DowsonD.IsaacJ. H.WroblewskiB. M.Laboratory wear tests and clinical observations of the penetration of femoral heads into acetabular cups in total replacement hip joints III: The measurement of internal volume changes in explanted Charnley sockets after 2–16 years in vivo and the determination of wear factorsWear, 1985, 104, 225–244.
17.
HallR. M.UnsworthA.SineyP.WroblewskiB. M.Wear in retrieved Charnley acetabular socketsProc. Instn Mech. Engrs, Part H: J. Engineering in Medicine, 1996, 210 (H3), 197–207.
18.
KaddickC.WimmerM. A.Hip simulator wear testing according to the newly introduced standard ISO 14242Proc. Instn Mech. Engrs, Part H: J. Engineering in Medicine, 2001, 215 (H5), 429–442.
19.
International standard ISO 14242–1Implants for surgery - wear of total hip-joint prostheses - Part 1: loading and displacement parameters for weartesting machines and corresponding environmental conditions for test, 2002 (International Organization for Standardization, Geneva, Switzerland).
20.
SaikkoV.A 12-station anatomic hip joint simulatorProc. IMechE, Part H: J. Engineering in Medicine, 2005, 219 (H6), 437–448.
21.
SaikkoV.Effect of lubricant protein concentration on the wear of ultra-high molecular weight polyethylene sliding against a CoCr counterfaceJ. Tribology, 2003, 125, 638–642.
22.
LivermoreJ.IlstrupD.MorreyB.Effect of femoral head size on wear of polyethylene acetabular componentJ. Bone Jt Surg., 1990, 72A, 518–528.
23.
SaikkoV.CaloniusO.KeränenJ.Effect of extent of motion and type of load on the wear of polyethylene in a biaxial hip simulatorJ. Biomed. Mater. Res. (Appl. Biomater.), 2003, 65B, 186–192.
24.
WangA.PolineniV. K.EssnerA.StarkC.DumbletonJ. H.Quantitative analysis of serum degradation and its effect on the outcome of hip joint simulator wear testing on UHMWPE. In 45th Annual Meeting of the Orthopaedic Research Society, Anaheim, California, 1–4 February 1999, p. 73.
25.
BergmannG.DeuretzbacherG.HellerM.GraichenF.RohlmannA.StraussJ.DudaG. N.Hip contact forces and gait patterns from routine activitiesJ. Biomechanics, 2001, 34, 859–871.
26.
MaxianT. A.BrownT. D.PedersenD. R.CallaghanJ. J.A sliding-distance-coupled finite element formulation for polyethylene wear in total hip arthroplastyJ. Biomechanics, 1996, 29, 687–692.
27.
TeohS. H.ChanW. H.ThampuranR.An elasto-plastic finite element model for polyethylene wear in total hip arthroplastyJ. Biomechanics, 2002, 35, 323–330.
28.
BevillS. L.BevillG. R.PenmetsaJ. R.PetrellaA. J.RullkoetterP. J.Finite element simulation of early creep and wear in total hip arthroplastyJ. Biomechanics, 2005, 38, 2365–2374.
29.
KangL.GalvinA. L.JinZ. M.FisherJ.A simple fully integrated contact-coupled wear prediction for ultra-high molecular weight polyethylene hip implantsProc. IMechE, Part H: J. Engineering in Medicine, 2006, 220 (H1), 33–46.
30.
SaikkoV.CaloniusO.Simulation of wear rates and mechanisms in total knee prostheses by ball-on-flat contact in a five-station, three-axis test rigWear, 2002, 253/4, 424–429.
