An Automotive Engine Charge-Air Intake Conditioner System: Analysis of Fuel Economy Benefits in a Gasoline Engine Application

Abstract

A combination of analytical techniques has been used to quantify the potential fuel economy benefits of an automotive engine charge-air intake conditioner system applied to a spark-ignited gasoline engine. This system employs a compressor, intercooler, and expander to provide increased charge density with the possibility of reducing charge-air temperature below sink temperature. This reduction in charge-air temperature provides the potential for improved knock resistance at full load; thereby allowing the possibility of increasing compression ratio with corresponding benefits in thermodynamic cycle efficiency and part-load fuel economy. The four linked and interfaced models comprised a first-law thermodynamic model of the charge-air conditioner system, a one-dimensional engine cycle simulation, a two-zone combustion model, and a knock criterion model. An analysis was carried out under full load at 3000 r/min and showed that a charge-air conditioner system - with compressor, intercooler, and expander efficiencies of 0.8 - allowed the compression ratio to be increased by approximately half a ratio, which gave up to 1.5 per cent reduction in brake specific fuel consumption at 2000 r/min 2 bar brake mean effective pressure when compared with a conventional pressure charger intercooler system with no expander.

Keywords

internal combustion engine pressure charging intercooling charge-air temperature expander compression ratio knock fuel economy

Get full access to this article

View all access options for this article.

References

Taitt

D. W.

Garner

C. P.

Swain

Bassett

M. D.

Pearson

R. J.

Turner

J. W. G.

An automotive engine charge-air intake conditioner system: Thermodynamic analysis of performance characteristics. Proc. Instn Mech. Engrs, Part D: J. Automobile Engineering, 2005, 219 (D3), 389–404.

Turner

J. W. G.

Pearson

R. J.

Bassett

M. D.

Blundell

D. W.

Taitt

D. W.

The turboexpansion concept - initial dynamometer results. SAE paper 2005–01-1853, 2005.

Douaud

A. M.

Eyzat

Four-octane-number method for predicting the anti-knock behaviour of fuels and engines. SAE paper 780080, 1978.

Winterbone

D. E.

Pearson

R. J.

Design techniques for engine manifolds, 1999 (Professional Engineering Publications, London).

Winterbone

D. E.

Pearson

R. J.

Theory of engine manifold design, 2000 (Professional Engineering Publications, London).

Barnes-Moss

H. W.

A designer's viewpoint. In Proceedings of IMechE Conference on

Passenger Car Engines, 1975, pp. 133–147 (MEP, London).

Horlock

J. H.

Winterbone

D. E.

The thermodynamics and gas dynamics of internal combustion engines, Vol. 2, 1986 (Clarendon Press, Oxford).

Annand

W. J. D.

Heat transfer in the cylinder of reciprocating internal combustion engines. Proc. Instn Mech. Engrs, 1963, 177, 973–990.

10.

Baruah

P. C.

Combustion and cycle calculations in spark ignition engines. In The thermodynamics and gas dynamics of internal combustion engines, Vol. 2 (Eds. Horlock

J. H.

Winterbone

D. E.

), 1986, Ch. 14 (Clarendon Press, Oxford).

11.

Heywood

J. B.

Internal combustion engine fundamentals, 1988 (McGraw-Hill, New York).

12.

Kempinski

Rife

J. M.

Knock in spark ignition engines. SAE paper 810147, 1981.

13.

Livengood

J. C.

P. C.

Correlation of auto-ignition phenomenon in internal combustion engines and rapid compression machines. In Proceedings of Fifth International Symposium on

Combustion, Pittsburgh, Pennsylvania, 1955, p. 347.