Finite element modelling of piston-ring dynamics and blow-by estimation in a four-cylinder diesel engine

Abstract

This paper presents the results of the simulation of piston-ring behaviour in a four-cylinder diesel internal combustion engine, using explicit finite element analysis. The finite element model consists of piston, piston rings, liners, connecting rods, and a crankshaft. The gas pressure and temperature are taken into account for the simulation. The mass flow is solved by using the explicit finite difference scheme. The ring geometry, its assembly load, and its mechanical and thermal properties are properly accounted for in the simulation. The ring dynamics are greatly influenced by the piston secondary motions that depend upon the piston geometry, piston pin offset, its centre-of-gravity location, and piston-liner clearance. The ring motions in the axial and radial directions are monitored; various gap areas are calculated to estimate the blow-by and compared with the experimental results. The mass flowrate obtained from the model agrees with the experimental values. The information obtained from the analysis serves as an input for piston and ring design and their development.

Keywords

internal combustion engine piston ring dynamics finite element modelling blow-by

Get full access to this article

View all access options for this article.

References

Ruddy

B. L.

Dowson

Economou

P. N.

Baker

A. J. S.

Piston ring lubrication - Part III: The influence of ring dynamics and ring twist. In Energy Conservation through Fluid Film Lubrication Technology: Frontiers in Research and Design, Proceedings of the ASME Winter Meeting, New York, USA, 1979, pp. 191–215 (American Society of Mechanical Engineers, New York).

Ruddy

B. L.

Parsons

Dowson

Economou

P. N.

The influence of thermal distortion and wear of piston ring groove upon the lubrication of piston rings in diesel engines. In Proceedings of the Sixth Leeds-Lyon Symposium on

Tribology, Lyon, France, 1979, 1980 (Mechanical Engineering Publications Limited, London).

Namazian

Heywood

J. B.

Flow in the piston-cylinder-ring crevices of a spark-ignition engine: Effect on hydrocarbon emissions, efficiency and power. SAE paper 820088, 1982, pp. 261–287.

Keribar

Dursunkaya

Flemming

M. F.

An integrated model of ring pack performance. Trans. ASME, J. Engng Gas Turbines Power, 1991, 113, 382–389.

Furuhama

Hiruma

Tsuzita

Piston ring motion and its influence on engine tribology. SAE paper 790860, 1979, pp. 2929–2941.

Herbst

H. M.

Priebsh

H. H.

Simulation of piston ring dynamics and their effect on oil consumption. SAE paper 2000–01-0919, pp. 862–873.

Richardson

D. E.

Comparison of measured and theoretical inter-ring gas pressure on a diesel engine. SAE paper 961909, 1996.

Kurbet

S. N.

Krishna Kumar

Finite element analysis of piston tilt effects on piston ring dynamics in multicylinder IC engines. Proc. Instn Mech. Engrs, Part K: J. Multi-body Dynamics, 2004, 218, 107–117.

ABAQUS/Explicit version 5.8–1, 1998 (Hibbitt Karrlsson & Sorensen, Pawtucket, Rhode Island).

10.

Yoshida

Kusama

Sagawa

Effects of surface treatments on piston ring friction force and wear. SAE paper 900589, 1990, pp. 1236–1244.

11.

Lawry

M. H.

I-DEAS master series, 1998 (Structural Dynamic Research Corporation, Milford, Ohio).

12.

Tian

Noordzij

L. B.

Wong

V. W.

Heywood

J. B.

Modeling piston-ring dynamics, blowby, and ring twist effects. Trans. ASME, Engng Gas Turbines Power, 1998, 120, 843–853.

13.

Kuo

T.-W.

Sellnau

M. C.

Theobald

M. A.

Jones

J. D.

Calculation of flow in the piston-cylinder-ring crevices of a homogeneous-charge engine and comparison with experiment. SAE paper 890838, 1989, pp. 1469–1482.

14.

Roberts

C. E.

Matthews

R. D.

Development of an improved ring pack model for hydrocarbon emissions studies. SAE paper 961966, 1196, pp. 1485–1491.

15.

Kurbet

S. N.

Krishna Kumar

Finite element modeling of piston ring dynamics and blowby estimation in single cylinder IC engine. In Proceedings of the ASME Internal Combustion Engine Division 2002 Fall Technical Conference, ICE-Vol. 39, pp. 481–487 (American Society of Mechanical Engineers, New York).

16.

Leschiutta

M. C.

Eng

J. A.

Martin

J. K.

Dynamic piston position measurements using a laser range-finding technique. SAE paper 900482, 1990, pp. 1111–1123.

17.

Wong

V.W.

Tian

Lang

Sekiya

J. P.

Ryan

Kobayashi

Aoyama

A numerical model of piston secondary motion and piston slap in partially flooded elastohydrodynamic skirt lubrication. SAE paper 940696, 1994, pp. 1276–1289.

18.

Knoll

Peeken

Lechtape-Gruter

Lang

Computer-aided simulation of piston and piston ring dynamics. Trans. ASME, J. Engng Gas Turbines Power, 1996, 118, 880–886.

19.

Tian

Wong

V. W.

Modeling the lubrication, dynamics, and effects of piston dynamic tilt of twin-land oil control rings in internal combustion engines. Trans. ASME, J. Engng Gas Turbines Power, 2000, 122, 119–129.

20.

Truscott

Reid

Ruddy

Ring dynamics in a diesel engine and its effect on oil consumption and blowby. SAE paper 831282, 1983, pp. 3.768–3.780.

21.

Furuhama

Tada

On the flow of gas through the piston-rings. Bull. JSME, 1962, 4, 691–698.

22.

Kurbet

S. N.

Finite element analysis of the dynamics of internal combustion engine. PhD Thesis, Indian Institute of Technology, Madras, India, 2004.