Karanja oil utilization in a direct-injection engine by preheating. Part 2: experimental investigations of engine durability and lubricating oil properties

Abstract

Straight vegetable oil utilization as a diesel engine fuel has the advantages of eliminating the energy, time, and cost involved in biodiesel production. Since straight vegetable oils have quite high viscosity compared with mineral diesel, they have to be modified to bring their combustion-related properties closer to mineral diesel. In this experimental study, a heat exchanger was designed and used to utilize the waste heat of exhaust gases for reducing the viscosity of Karanja oil by preheating. Carbon deposits, wear of vital engine components, and various effects of utilizing preheated Karanja oil on lubricating oil were analysed during a long-term endurance test executed for 512h. Carbon deposits on various critical parts of the power cell were analysed by visual inspection. For pistons, the piston merit rating was determined. The effect on a lubricating oil because of heated Karanja oil vis-à-vis mineral diesel was evaluated by comparing the densities, viscosities, flash points, carbon residues, ash contents, copper corrosion effect and pentane, benzene insolubility measurements at intervals of every 128h for 512h. The wear of the cylinder liner, piston rings, gudgeon pin, and small- and big-end bearings for a Karanja-oil-fuelled engine were also measured and compared vis-à-vis mineral diesel-fuelled engine.

Keywords

biofuels lubricating oil tribology wear piston rating durability atomic absorption spectroscopy

Get full access to this article

View all access options for this article.

References

Openshaw

‘A review of Jatropha curcas: an oil plant of unfulfilled promise.’

Biomass Bioenergy 19 (1) (2000): 1–15.

Agarwal

A. K.

Das

L. M.

‘Biodiesel development and characterization for use as a fuel in compression ignition engine.’

Trans. ASME, J. Engng Gas Turbines Power 123 (2001): 440–447.

Ramadhas

A. S.

Jayaraj

Muraleedharan

‘Use of vegetable oils as I.C. engine fuels – a review.’

Renewable Energy 29 (2004): 727–742.

Agarwal

A. K.

‘Biofuels (alcohols and biodiesel) applications as fuels for internal combustion engines.’

Prog. Energy Combust. Sci. 33 (2006): 233–271.

Agarwal

A. K.

‘Scope and limitation of utilization of non-edible vegetable oils as a substitute fuel for diesel engines: an experimental study.’ Project Report, submitted to the Department of Science and Technology, Government of India, 2008.

Kumar

M. S.

Ramesh

Nagalingam

‘An experimental comparison of methods to use methanol and Jatropha oil in a compression ignition engine.’

Biomass Bioenergy 25 (2003): 309–318.

Agarwal

A. K.

Rajamanoharan

‘Experimental investigations of performance and emissions of Karanja oil and its blends in a single cylinder agricultural diesel engine.’

Appl. Energy 86 (1) (2009): 106–112.

Banapurmath

N. R.

Tewari

P. G.

Hosmath

R. S.

‘Performance and emission characteristics of a DI compression ignition engine operated on Honge, Jatropha and sesame oil methyl esters.’

Renewable Energy 33 (9) (2008): 1982–1988.

Nwafor

O. M. I.

‘Emission characteristics of diesel engine running on vegetable oil with elevated fuel inlet temperature.’

Biomass Bioenergy 27 (2004): 507–511.

10.

Bari

Lim

T. H.

C. W.

‘Effects of preheating of crude palm oil (CPO) on injection system, performance and emission of a diesel engine.’

Renewable Energy 27 (2002): 339–351.

11.

Mahanta

Mishra

S. C.

Kushwah

Y. S.

‘An experimental study of Pongamia pinnata L. oil as a diesel substitute.’

Proc. IMechE, Part A: J. Power and Energy 220 (7), 803–808 DOI: 10.1243/09576509JPE172.

12.

Labeckas

Slavinskas

‘Performance of direct-injection off-road diesel engine rapeseed oil.’

Renewable Energy 31 (2006): 849–863.

13.

Almeida

S. C. A. D.

Belchior

C. R.

Nascimento

M. V. G.

Vieira

L. D. S. R.

Fleury

‘Performance of a diesel generator fuelled with palm oil.’

Fuel 81 (2002): 2097–2102.

14.

Stanislav

Jerman

M. S.

Kegl

‘Biodiesel influence on tribology characteristics of a diesel engine.’

Fuel 88 (6) (2009): 970–979.

15.

IS 10000: 1980. Methods of tests for internal combustion engines (Bureau of Indian Standards 1980).

16.

IP/247/69. Merit rating system for engine cleanliness and wear (Institute of Petroleum).

17.

CRC manual 16, carburetor and induction system rating manual (Coordinating Research Council).

18.

CRC manual 17, Distress rating manual (Coordinating Research Council).

19.

ASTM D482. Standard test method for ash from petroleum products (ASTM International 2007).

20.

ASTM D189. Standard test method for Conradson carbon residue of petroleum products (ASTM International 2005).

21.

ASTM D130–IP 154. Standard test method for detection of copper corrosion from petroleum products by the copper strip tarnish test (ASTM International 2004).

22.

ASTM D4048. Standard test method for detection of copper corrosion from lubricating grease (ASTM International 2002).

23.

IP 112. Determination of corrosiveness to copper of lubricating grease – copper strip method (Institute of Petroleum).

24.

IP 227. Corrosiveness to silver of aviation turbine fuels (Institute of Petroleum).

25.

BS 2000 Part 112: methods of test for petroleum and its products. Determination of corrosiveness to copper of lubricating grease. Copper strip method (British Standards Institution 2002).

26.

BS 2000 Part 154: methods of test for petroleum and its products. Detection of copper corrosion from petroleum products by the copper strip tarnish test (British Standards Institution 1993).