This paper presents results from the analysis of experimental data with the aim of investigating the cyclic, instantaneous heat transfer phenomena occurring in both the cylinder head and exhaust manifold wall surfaces of a direct injection, air-cooled diesel engine, operating under transient events (long-term), viz. during a sudden change in engine speed and/or load, rather than the usual steady state. The experimental installation allowed both for long- and short-term signal types to be recorded on a common time reference base during the transient event. Processing of experimental data was accomplished using a modified version of one-dimensional heat conduction theory with Fourier analysis, capable of catering for the special characteristics of transient engine operation. Based on this model, the evolution of local surface heat flux during a transient event was calculated. Two engine transient events are examined, which present a key difference in the way the load and speed changes are imposed on each one of them. It is revealed that in the case of a ‘ramp’ transient the amplitude of wall surface temperature and heat flux variation in the combustion chamber during the first 20 engine cycles was increased by almost three times more than the corresponding ones during steady state operation. At the same time, temporal gradients of cylinder pressure and wall surface temperature are also sharply increased in the combustion chamber and exhaust manifold surfaces. The variation of cylinder pressure, surface temperature, and heat flux is altered significantly during the transient event, with their peak values either advanced or retarded compared with those for the corresponding steady state operation. The previous observations are moderated or even vanished in the case of a ‘slow pace’ transient variation, revealing the significant influence of engine speed and load triggered by the external command, on the response of heat transfer variables. During a ramp transient, the amplitude of wall temperature swing is increased significantly even at a depth of a few millimetres below the surface of the combustion chamber, thereby influencing the dissipation of heat towards its external layers. Under these circumstances, the depth of penetration for temperature oscillations inside the metal volume is also significantly increased.
AnnandW. J. D.‘Heat transfer in the cylinders of reciprocating internal combustion engines.’Proc. Instn Mech. Engrs177 (1963): 973–990.
5.
BormanG.NishiwakiK.‘Internal-combustion engine heat transfer.’Prog. Energy Combust. Sci.13 (1987): 1–46.
6.
AssanisD. N.HeywoodJ. B.‘Development and use of a computer simulation of the turbocompounded diesel engine performance and component heat transfer studies.’ SAE paper 860329, 1986.
7.
WhitehouseN. D.‘Heat transfer in a quiescent chamber diesel engine.’Proc. Instn Mech. Engrs185 (1970–71): 963–975 DOI: 10.1243/PIME_PROC_1970_185_109_02.
8.
RakopoulosC. D.RakopoulosD. C.GiakoumisE. G.KyritsisD. C.‘Validation and sensitivity analysis of a two-zone diesel engine model for combustion and emissions prediction.’Energy Conversion Mgmt45 (2004): 1471–1495.
9.
RakopoulosC. D.RakopoulosD. C.KyritsisD. C.‘Development and validation of a comprehensive two-zone model for combustion and emissions formation in a DI diesel engine.’Int. J. Energy Res.27 (2003): 1221–1249.
10.
RakopoulosC. D.AntonopoulosK. A.RakopoulosD. C.HountalasD. T.‘Multi-zone modeling of combustion and emissions formation in DI diesel engine operating on ethanol-diesel fuel blends.’Energy Conversion Mgmt49 (2008): 625–643.
11.
RakopoulosD. C.RakopoulosC. D.GiakoumisE. G.PapagiannakisR. G.KyritsisD. C.‘Experimental-stochastic investigation of the combustion cyclic variability in HSDI diesel engine using ethanol-diesel fuel blends.’Fuel87 (2008): 1478–1491.
12.
RakopoulosC. D.AntonopoulosK. A.RakopoulosD. C.‘Development and application of multi-zone model for combustion and pollutants formation in direct injection diesel engine running with vegetable oil or its bio-diesel.’Energy Conversion Mgmt48 (2007): 1881–1901.
13.
KeribarR.MorelT.‘Thermal shock calculations in I.C. engines.’ SAE paper 870162, 1987.
14.
MorelT.WahiduzzamanS.FortE. F.‘Heat transfer experiments in an insulated diesel.’ SAE paper 880186, 1988.
15.
EnomotoY.FuruhamaS.‘A study of the local heat transfer coefficient on the combustion chamber walls of a four-stroke gasoline engine.’Bull. JSME32 (1989): 107–114.
16.
KamoR.BryzikW.‘Cummins/TACOM advanced adiabatic engine.’ SAE paper 840428, 1984.
17.
AssanisD. N.‘Effect of combustion chamber insulation on the performance of a low heat rejection diesel engine with exhaust heat recovery.’Heat Recov. Syst. CHP9 (1989): 475–484.
18.
RakopoulosC. D.AntonopoulosK. A.RakopoulosD. C.GiakoumisE. G.‘Investigation of the temperature oscillations in the cylinder walls of a diesel engine with special reference to the limited cooled case.’Int. J. Energy Res.28 (2004): 977–1002.
19.
Perez-BlancoH.‘Experimental characterization of mass, work and heat flows in an air cooled, single cylinder engine.’Energy Conversion Mgmt45 (2004): 157–169.
20.
WuY.ChenB.HsiehF.KeC.‘Heat transfer model for scooter engines.’ SAE paper 2008-01-0387, 2008.
21.
NakashimaK.TodaT.IshiharaS.YamamotoM.‘Optimizing the cooling effect of fins with slits on an air-cooled cylinder by increasing natural convection.’ SAE paper 2008-01-1170, 2008.
22.
ChangJ.FilipiZ.AssanisD. N.KuoT.-W.NajtP.RaskR.‘Characterizing the thermal sensitivity of a gasoline homogeneous charge compression ignition engine with measurements of instantaneous wall temperature and heat flux.’Int. J. Engine Res.6 (2005): 289–309 DOI: 10.1243/146808705X30558.
23.
ChangJ.GüralpO.FilipiZ.AssanisD. N.KuoT.-W.NajtP.RaskR.‘New heat transfer correlation for an HCCI engine derived from measurements of instantaneous surface heat flux.’ SAE paper 2004-01-2996, 2004.
24.
AlkidasA. C.MyersJ. P.‘Transient heat-flux measurements in the combustion chamber of a spark-ignition engine.’Trans. ASME, J. Heat Transfer104 (1982): 62–67.
25.
AlkidasA. C.ColeR. M.‘Transient heat-flux measurements in a divided-chamber diesel engine.’Trans. ASME, J. Heat Transfer107 (1985): 439–444.
26.
DolzV.LujanJ. M.SerranoJ. R.ArnauF.‘Heat transfer model to calculate turbocharged HSDI diesel engines performance.’ SAE paper 2003-01-1066, 2003.
27.
LiuZ.JiangY.DongZ.PiB.LiuY.‘3-D numerical simulation of transient heat transfer among multi-component coupling system in internal combustion chamber.’ SAE paper 2008-01-1818, 2008.
28.
KandaT.‘Study on Euro IV combustion technologies for direct injection diesel engine.’ SAE paper 2004-01-0113, 2004.
29.
MureC. R.RheeK. T.‘Instantaneous heat transfer over the piston of a motored direct injection-type diesel engine.’ SAE paper 890469, 1989.
30.
SerranoJ. R.GalindoJ.BermúdezV.LópezrJ. J.‘Cycle-to-cycle diesel combustion characterization during engine transient operation.’ SAE paper 2001-01-3262, 2001.
31.
RakopoulosC. D.MavropoulosG. C.‘Study of the steady and transient temperature field and heat flow in the combustion chamber components of a medium speed diesel engine using finite element analyses.’Int. J. Energy Res.20 (1996): 437–464.
32.
RakopoulosC. D.MavropoulosG. C.‘Experimental instantaneous heat fluxes in the cylinder head and exhaust manifold of an air-cooled diesel engine.’Energy Conversion Mgmt41 (2000): 1265–1281.
33.
ChoK.-W.AssanisD.FilipiZ.SzekelyG.NajtP.RaskR.‘Experimental investigation of combustion and heat transfer in a direct-injection spark ignition engine via instantaneous combustion chamber surface temperature measurements.’Proc. IMechE, Part D: J. Automobile Engineering222 (2008): 2219–2233 DOI: 10.1243/09544070JAUTO853.
34.
Oude NijewemeD. J.KokJ. B. W.StoneC. R.WyszynskiL.‘Unsteady in-cylinder heat transfer in a spark ignition engine: experiments and modelling.’Proc. IMechE, Part D: J. Automobile Engineering215 (2001): 747–760 DOI: 10.1243/0954407011528329.
35.
BohacS. V.BakerD. M.AssanisD. N.‘A global model for steady state and transient S.I. engine heat transfer studies.’ SAE paper 960073, 1996.
36.
LinC. S.FosterD. E.‘An analysis of ignition delay, heat transfer and combustion during dynamic load changes in a diesel engine.’ SAE paper 892054, 1989.
37.
AssanisD. N.FilipiZ. S.FivelandS. B.SyrimisM.‘A methodology for cycle-by-cycle transient heat release analysis in a turbocharged direct injection diesel engine.’ SAE paper 2000-01-1185, 2000.
38.
WangX.StoneC. R.‘A study of combustion, instantaneous heat transfer, and emissions in a spark ignition engine during warm-up.’Proc. IMechE, Part D: J. Automobile Engineering222 (2008): 607–618 DOI: 10.1243/09544070JAUTO610.
39.
RakopoulosC. D.GiakoumisE. G.RakopoulosD. C.‘Study of the short-term cylinder wall temperature oscillations during transient operation of a turbocharged diesel engine with various insulation schemes.’Int. J. Engine Res.9 (2008): 177–193 DOI: 10.1243/14680874JER00608.
40.
FarrugiaM.AlkidasA. C.SangeorzanB. P.‘Cycle-averaged heat flux measurements in a straight-pipe extension of the exhaust port of a SI engine.’Trans. SAE, J. Engines115 (2006): 565–575 (SAE paper 2006-01-1033, 2006).
41.
SammutG.AlkidasA. C.‘Relative contributions of intake and exhaust tuning on SI engine breathing – a computational study.’ SAE paper 2007-01-0492, 2007.
42.
BalzanN.SangeorzanB.AlkidasA. C.‘Steady-state local heat flux measurements in a straight pipe extension of an exhaust port of a spark ignition engine.’ SAE paper 2007-01-3990, 2007.
43.
HellerS.WachtmeisterG.‘Analysis and modeling of heat transfer in the SI engine exhaust system during warm-up.’Trans. SAE, J. Engines116 (2007): 673–686 (SAE paper 2007-01-1092, 2007).
44.
RanganathanR. P.TurnerD. W.FranchettM. E.‘Exhaust manifold gas temperature predictions using system level data driven modelling.’ SAE paper 2005-01-0698, 2005.
45.
RakopoulosC. D.HountalasD. T.MavropoulosG. C.GiakoumisE. G.‘An integrated transient analysis simulation model applied in thermal loading calculations of an air-cooled diesel engine under variable speed and load conditions.’Trans. SAE, J. Engines106 (1997): 923–939 (SAE paper 970634, 1997).
46.
RakopoulosC. D.MavropoulosG. C.HountalasD. T.‘Modeling the structural thermal response of an air-cooled diesel engine under transient operation including a detailed thermodynamic description of boundary conditions.’ SAE paper 981024, 1998.
47.
RakopoulosC. D.MavropoulosG. C.‘Components heat transfer studies in a low heat rejection DI diesel engine using a hybrid thermostructural finite element model.’Appl. Thermal Engng18 (1998): 301–316.
48.
RakopoulosC. D.RakopoulosD. C.MavropoulosG. C.GiakoumisE. G.‘Experimental and theoretical study of the short term response temperature transients in the cylinder walls of a diesel engine at various operating conditions.’Appl. Thermal Engng24 (2004): 679–702.
49.
RakopoulosC. D.MavropoulosG. C.‘Experimental evaluation of local instantaneous heat transfer characteristics in the combustion chamber of air-cooled direct injection diesel engine.’Energy33 (2008): 1084–1099.
50.
MavropoulosG. C.RakopoulosC. D.HountalasD. T.‘Experimental assessment of instantaneous heat transfer in the combustion chamber and exhaust manifold walls of air-cooled direct injection diesel engine.’SAE Int. J. Engines1 (1) (2008): 888–912 (SAE paper 2008-01-1326, 2008).
51.
MavropoulosG. C.RakopoulosC. D.HountalasD. T.‘Experimental investigation of instantaneous cyclic heat transfer in the combustion chamber and exhaust manifold of a DI diesel engine under transient operating conditions.’ SAE paper 2009-01-1122, 2009.
52.
MorelT.KeribarR.BlumbergP.‘Cyclical thermal phenomena in engine combustion chamber surfaces.’ SAE paper 850360, 1985.
53.
BeckB. T.‘Demonstrations of transient conduction heat flux phenomena for the engineering laboratory.’ In Proceedings of the 32nd ASEE/IEEE Conference on Frontiers in Education, Boston, Massachusetts, 6–9 November 2002, pp. 1–6.
54.
RakopoulosC. D.MavropoulosG. C.‘Modelling the transient heat transfer in the ceramic combustion chamber walls of a low heat rejection diesel engine.’Int. J. Veh. Des.22 (1999): 195–215.
55.
WeltyJ. R.Engineering heat transfer (John Wiley1974).
56.
RakopoulosC. D.GiakoumisE. G.Diesel engine transient operation – principles of operation and simulation analysis (Springer2009).
57.
Temperature Measurement Handbook, Vol. VIII (NANMAC1997).
58.
ShuG.WeiH.‘Study of combustion noise mechanism under accelerating operation of a naturally aspirated diesel engine.’Int. J. Vehicle Des.45 (2007): 33–46.
