Semi-active vibration isolation using a near-zero-spring-rate device: steady state analysis of a single-degree-of-freedom model

Abstract

A vibration isolator is described which incorporates a near-zero-spring-rate device within its operating range. The device is an assembly of a vertical spring in parallel with two inclined springs. A low spring rate is achieved by combining the equivalent stiffness in the vertical direction of the inclined springs with the stiffness of the vertical central spring. It is shown that there is a relation between the geometry and the stiffness of the individual springs that results in a low spring rate. Computer simulation studies of a single-degree-of-freedom model for harmonic base input show that the performance of the proposed scheme is superior to that of the passive schemes with linear springs and skyhook damping configuration. The response curves show that, for small to large amplitudes of base disturbance, the system goes into resonance at low frequencies of excitation. Thus, it is possible to achieve very good isolation over a wide low-frequency band. Also, the damper force requirements for the proposed scheme are much lower than for the damper force of a skyhook configuration or a conventional linear spring with a semi-active damper.

Keywords

zero spring rate friction damper semi-active vibration isolation

Get full access to this article

View all access options for this article.

References

Karnopp

Crosby

M. J.

Harwood

R. A.

‘Vibration control using semi-active force generators.’

Trans. ASME, J. Engng Ind. 96 (5) (1974): 619–626.

Rakheja

Sankar

‘Effectiveness of on–off damper in isolating dynamical systems.’

Shock Vibr. Bull. 56 (1986): 147–156.

Queslati

Sankar

‘A class of semi-active suspension schemes for vehicle vibration control.’

J. Sound Vibr. 172 (3) (1994): 391–411.

Jolly

M. R.

Miller

L. R.

‘The control of semi-active dampers using relative feedback signals.’ SAE paper 892483, 1989, pp. 569–577.

Karnopp

‘Design principles for vibration control systems using semi-active dampers.’

Trans. ASME, J. Dynamic Systems, Measmt Control 112 (1990): 448–455.

Karnopp

‘Active and semi-active vibration isolation.’

Trans. ASME Special 50th Anniversary Design Issue, Combined Issue of J. Med. Des. and J. Vibr. Acoust. 117 (1995): 177–185.

Griffin

Gussy

Lane

S. A.

Henderson

B. K.

Sciulli

‘Virtual skyhook vibration isolation system.’

Trans. ASME, J. Vibr. Acoust. 124 (2002): 63–67.

Liu

Matsuhisa

Utsuno

‘Semi-active vibration isolation system with variable stiffness and damping control.’

J. Sound Vibr. 313 (2008): 16–28.

Choi

Y.-T.

Wereley

N. M.

Jeon

Y.-S.

‘Semi-active vibration isolation using magnetorheological isolators.’

AIAA J. Aircr. 42 (5) (2005): 1244–1251.

10.

Youn

Hac

‘Semi-active suspension with adaptive capability.’

J. Sound Vibr. 180 (3) (1995): 475–492.

11.

Liu

Matsuhisa

Utsuno

Park

J. G.

‘Vibration isolation by a variable stiffness and damping system.’

Int. J. Japan Soc. Mech. Engng (Ser. C) 48 (2) (2005): 305–310.

12.

Liu

Matsuhisa

Utsuno

Park

J. G.

‘Vibration control by a variable damping and stiffness with magnetorheological dampers.’

Int. J. Japan Soc. Mech. Engng (Ser. C) 49 (2) (2006): 411–417.

13.

Karkoub

M. A.

Zribi

‘Active/semi-active suspension control using magnetorheological actuators.’

Int. J. Systems Sci. 37 (1) (2006): 35–44.

14.

Song

Ahmadian

‘Study of semi-active adaptive control algorithms with magnetorheological seat suspension.’ SAE paper 2004-01-1648, 2004.

15.

Boerner

E. H.

‘Constant force compression springs.’

Prod. Engng 23 (9) (1960): 129.

16.

Snowdon

J. C.

Vibration and shock in damped mechanical systems (John Wiley 1968).

17.

Crede

C. E.

Vibration and shock isolation (John Wiley 1951).

18.

Tobias

S. A.

‘Design of small isolator units for the suppression of low frequency vibration.’

Proc. Instn Mech. Engrs, J. Mechanical Engineering Science 1 (3) (1959): 280–292 DOI: 10.1243/JMES.JOUR_1959_001_032_02.

19.

Woodard

S. E.

Housner

‘Nonlinear behaviour of a passive zero spring rat suspension system.’

AIAA J. Guidance, Control Dynamics 14 (1) (1991): 84–89.

20.

Ibrahim

R. A.

‘Recent advances in nonlinear passive vibration isolators.’

J. Sound Vibr. 314 (2008): 371–452.

21.

Chironis

N. P.

Spring design and application (McGraw-Hill 1961).

22.

Carella

Brennan

M. J.

Waters

T. P.

‘Static analysis of a passive vibration isolator with quasi-zero-stiffness characteristic.’

J. Sound Vibr. 301 (2007): 678–689.