Characteristic study of bushing compliance in consideration of stresses in a vehicle suspension system by the Taguchi method

Abstract

The dynamic loads imposed on suspension components during vehicle driving are transferred through bushings and joints. The loads from bushings are important factors in the prediction of the fatigue life of a component and the dynamic characteristics of a vehicle. In this paper, the linear characteristic of a bushing is approximated by finite element analysis and applied to a multi-body dynamic model of the vehicle. The influence of bushing compliance is investigated, considering the dynamically responsive stress of the lower control arm in a virtual proving ground test. With the bushing compliance of the front suspension as a design parameter, the Taguchi method is used in the systematic process of a robust design to reduce the stress value of the lower control arm.

Keywords

Taguchi method vehicle dynamic analysis finite element analysis S/N ratio orthogonal array table suspension system bushing compliance

Get full access to this article

View all access options for this article.

References

Haiba

Barton

D. C.

Brooks

P. C.

Levesley

M. C.

Using a quarter-vehicle multi-body model to estimate the service loads of a suspension arm for durability calculations. Proc. Instn Mech. Engrs, Part K: J. Multi-body Dynamics, 2003, 217 (2), 121–133.

Bishop

N. W. M.

Steinbeck

Sherratt

Finite element based fatigue calculations, 2000 (NAFEMS).

Kim

M. S.

Lee

C. W.

Son

S. H.

Yim

H. J.

Heo

S. J.

Shape optimization for improving fatigue life of a lower control arm using the experimental design. Trans. Korean Soc. Automot. Engrs, 2003, 11 (3), 161–166.

Blundell

M. V.

The influence of rubber bushing compliance on vehicle suspension movement. Mater. and Des., 1998, 19, 29–37.

Levesley

M. C.

Kember

S. A.

Barton

D. C.

Brooks

P. C.

Querin

O. M.

Dynamic simulation of vehicle suspension systems for durability analysis. Mater. Sci. Forum, 2003, 440, 103–110.

Song

S. J.

Tak

T. O.

Kinematic design sensitivity analysis of suspension system using a symbolic computation method. Trans. Korean Soc. Automot. Engrs, 1966, 4 (6), 247–259.

Tak

T. O.

Kinematic design sensitivity analysis of vehicle suspension systems using a numerical differentiation method. Trans. Korean Soc. Automot. Engrs, 1998, 6 (5), 128–137.

Kim

S. J.

Kim

C. J.

Park

T. W.

Suspension parameter design using a design of experiments. Trans. Korean Soc. Automot. Engrs, 1995, 4 (1), 16–27.

Sohn

J. H.

Kim

K. S.

Yoo

W. S.

Selection of toe geometry and bushing stiffness to improve the vehicle handling characteristics. Trans. Korean Soc. Automot. Engrs, 1999, 7 (5), 186–193.

10.

Ryu

J. H.

Kim

H. S.

Wang

S. M.

A method of improving dynamic stress computation for fatigue life prediction of vehicle structure. SAE paper 971534, 1997.

11.

MSC/ADAMS User Manual, 1998 (Mechanical Dynamics Inc., Ann Arbor, MI, USA).

12.

MSC/Nastran 2001 Reference Manual, 2002 (MSC Software Co., Santa Ana, CA, USA).

13.

Phadke

M. S.

AT&T Bell Laboratories, Quality engineering using robust design, 1989 (Prentice-Hall, Englewood Cliffs, New Jersey).

14.

15.

Heinrietz

Lehrke

H. P.

Rupp

A. N.

Barthel

Identification of parametric tire models for the fatigue evaluation of suspension components. SAE paper 2003–01-1276, 2003.

16.

Berzri

Dhir

Ranganathan

Balendran

Jayakumar

A new tire model for road loads simulation: Full vehicle validation. SAE paper 2004–01-1579, 2004.

17.

Ghosh

Medepalli

Effect of tire stiffness on vehicle loads. SAE paper 2005–01-0825, 2005.