Prediction of drop size distribution in a spray from a pressure swirl atomizer using maximum entropy formalism

Abstract

Drop size distribution is an important characterizing parameter of a spray. In the present work a theoretical model has been described, based on the maximum entropy formalism principle, for the determination of the drop size distribution in a spray issued from a pressure swirl atomizer. The atomization efficiency is also derived from the model, assuming the velocities of all the drop sizes to be uniform. The results show that the drop size distribution, described from the present model, resembles the Rosin-Rammler type distribution very well, with a dispersion parameter of 3.47. The atomization efficiency is found to decrease with the increase in liquid mass flowrates, when the pressure differential across the atomizer remains the same. On the other hand, an increase in the orifice diameter increases the atomization efficiency, when the liquid mass flow rate and pressure differential are the same. The ratio of the surface energy to the kinetic energy at the atomizer exit is seen to influence the atomization efficiency.

Keywords

atomization spray size distribution pressure swirl atomizer information entropy

Get full access to this article

View all access options for this article.

References

Lefebvre

A. H.

Atomization and Sprays, 1989 (Hemisphere Publishing, New York).

Rizk

N. K.

Lefebvre

A. H.

Internal flow characteristics of simplex swirl atomizers. Am. Inst. Aeronaut. Astronaut. J. Propulsion and Power, 1985, 1(3), 193–199.

Kutty

P. S.

Narasimhan

M. V.

Narayanaswamy

Design and prediction of discharge rate, cone angle and air core diameter of swirl chamber atomizers. In Proceedings of 1st International Conference on Liquid Atomization and Spray Systems, Tokyo, Japan, 1978, pp. 93.

Datta

Som

S. K.

Numerical prediction of air core diameter, coefficient of discharge and spray cone angle of a swirl spray pressure nozzle. Int. J. Heat and Fluid Flow, 2000, 21, 412–419.

Dash

S. K.

Halder

Peric

Som

S. K.

Formation of air core in nozzles with tangential entry. Trans. ASME, J. Fluid Engng, 2001, 123(4), 829–835.

Giffen

Muraszew

Atomization of Liquid Fuels, 1953 (Chapman and Hall, London).

Babu

K. R.

Narasimhan

M. V.

Narayanaswamy

Correlations for prediction of discharge rate, cone angle and air core diameter of swirl spray atomizers. In Proceedings of 2nd International Conference on Liquid Atomization and Spray Systems, Madison, Wisconsin, 1982, p. 91.

Rizk

N. K.

Lefebvre

A. H.

Prediction of velocity coefficients and spray cone angle for simplex swirl atomizers. In Proceedings of 3rd International Conference on Liquid Atomization and Spray Systems, London, 1985, pp. IIIC/2/1–16.

Wang

X. F.

Lefebvre

A. H.

Mean drop sizes from pressure swirl nozzles. Am. Inst. Aeronaut. Astronaut. J. Propulsion and Power, 1987, 3(1), 11–18.

10.

Wang

X. F.

Lefebvre

A. H.

Influence of ambient air pressure on pressure swirl atomization. Atomization and Spray Technol., 1987, 3(3), 209–226.

11.

Sellens

R. W.

Brzustowski

T. A.

A simplified prediction of droplet velocity distribution in a spray. Combust. Flame, 1986, 65, 273–279.

12.

Tankin

R. S.

Derivation of droplet size distribution in sprays using information theory. Combust. Sci. Technol., 1988, 60, 345–357.

13.

Tankin

R. S.

Prediction of droplet size and velocity distributions in sprays using maximum entropy principle. Combust. Sci. Technol., 1989, 68, 147–155.

14.

Boyaval

Dumouchel

The maximum entropy formalism and the determination of spray drop size distribution. In Proceedings of ILASS-Europe, Manchester, 1988, p. 1.

15.

Dobre

Bolle

Theoretical prediction of ultra-sonic spray characteristics using the maximum entropy formalism. In Proceedings of ILASS-Europe, Manchester, 1998, p. 7.

16.

Cousin

Yoon

S. J.

Dumouchel

Coupling of classical linear theory and maximum entropy formalism for prediction of drop size distribution in sprays: Application to pressure swirl atomizers. Atomization and Sprays, 1996, 6, 601–622.