A thin section filling model is summarized which adopts a finite element solution to the governing equations. This is compared with three experimental case studies. Two experimental case studies were established in this work, one based on flow visualization and the second on an experiment that uses a short shot method to build an image of the metal flow pattern into a pressure die cast part. This shows how a jet forms at the gate early in the filling stage and that filling is completed in a zone opposite this gate section. When the numerical model was compared with experimental data gathered from a gravity sand casting and a simple semicylindrical section, very good agreement was displayed when a turbulent flow model was adopted. This model was also compared with results from the pressure die cast part, but with less success since at this stage of development it is not capable of capturing the hydraulic losses that are associated with sharp changes in section and flow direction.
PickinJ.TraversE. J.Practical experience with the MAGMA soft mould filling and solidification program. In Solidification Simulation 2: Simulating Casting in the Foundry, The Institute of Metals, 22–23 April 1991.
3.
AnzaiK.UchidaT.Mould filling patterns of flat plate die castings. In Proceedings of Modelling of Casting, Welding and Advanced Solidification Processes, Vol. V, 1991, pp. 741–748 (The Minerals, Metals and Materials Society).
4.
WangH. P.PerryE. M.An iterative parametric analysis tool for thin-walled investment casting. In Proceedings of Modelling of Casting, Welding and Advanced Solidification Processes, Vol. V, 1991, pp. 595–602 (The Minerals, Metals and Materials Society).
5.
ZhangY. F.LiuW. K.WangH. P.Casting filling simulations of thin-walled cavities with solidification. In Proceedings of Modelling of Casting, Welding and Advanced Solidification Processes, Vol. VI, 1993, pp. 413–420 (The Minerals, Metals and Materials Society).
6.
ChanK. S.PericleousK.CrossM.Numerical simulation of flows encountered during mould filling. Appl. Math. Modelling, 1991, 15, 624–631.
7.
XuZ. A.MampaeyF.Simulation and experimental validation of mould filling for castings. In Proceedings of COST 504 Conference on Advanced Casting and Solidification Technology, 1994, pp. 367–385.
8.
SciamaG.JournãeF.Simulation of filling by vertical tapering sprues: Experimental verification. In Proceedings of COST 504 Conference on Advanced Casting and Solidification Technology, 1994, pp. 393–408.
9.
BoothS. E.AllsopD. F.Cavity flow studies at BNF Metals Technology Centre using water modelling techniques. In Proceedings of 12th International Die Casting Congress, Minneapolis, Minnesota, 1985.
10.
SulaimanS. B.GethinD. T.A network technique for metal flow analysis in the filling system of pressure die casting and its experimental verification on a cold chamber machine. Proc. Instn Mech. Engrs, Part B, Journal of Engineering Manufacture, 1992, 206(B4), 261–275.
11.
AbdullahS.GethinD. T.Finite element formulation for filling a thin section cavity. Int. J. Numer. Meth. Heat and Fluid Flow, 1997, 7, 344–366.
12.
AnzaiK.NiyamaE.Quasi three-dimensional mould filling simulation system for prediction of defects in die castings. In Proceedings of Modelling of Casting and Welding Processes, Vol. IV, 1988, pp. 471–485 (The Minerals, Metals and Materials Society).
13.
NgC. W.PanC. H. T.A linearised turbulent lubrication theory. Trans. ASME, J. Basic Engng, 1965, 87, 675–688.
14.
HirtC. W.AmsdenA. A.CookJ. L.An arbitrary Lagrangian-Eulerian computing method for all flow speeds. J. Comput. Physics, 1974, 14, 227–253.
15.
HirtC. W.NicholsB. D.Volume of fluid (VOF) method for the dynamics of free boundaries. J. Comput. Physics, 1981, 39, 201–225.
16.
DhattG.GaoD. M.Ben CheikhA.A finite element simulation of metal flow in moulds. Int. J. Numer. Meth. Engng, 1990, 30, 821–831.
17.
ThomsonE.Use of pseudo-concentrations to follow creeping viscous flows during transient analysis. Int. J. Numer. Meth. Fluids, 1986, 6, 749–761.
18.
DoneaJ.A Taylor-Galerkin method for convective transport problems. Int. J. Numer. Meth. Engng, 1984, 20, 101–119.
19.
SirrellB.HollidayM.CampbellJ.The benchmark test 1995. In Proceedings of Modelling of Casting, Welding and Advanced Solidification Processes, Vol. VII, 1995, pp. 915–933 (The Minerals, Metals and Materials Society).
20.
CodinaR.SchäferU.OñateE.Mould filling simulation using finite elements. Int. J. Numer. Meth. Heat and Fluid Flow, 1994, 4, 291–310.
21.
LewisR. W.RavindranK.TranD. V.Finite element modelling of the benchmark. In Proceedings of 7th International Conference on Modelling of Casting, Welding and Advanced Solidification Processes, The Minerals, Metals and Materials Society, 10–15 September 1995, pp. 955–962.
22.
LewisR. W.UsmaniA. S.CrossJ. T.Efficient mould filling simulation in castings by an explicit finite element method. Int. J. Numer. Meth. Fluids, 1995, 20, 493–506.
