A combined experimental model for a gravity die casting is presented. The experiments were shown to yield consistent results and confirmed earlier studies, which showed that interfacial heat transfer depends on the casting solidification state and that only its maximum value is affected by die coat thickness. The numerical model was found to capture the thermal transients when interface effects were included and when the removal of cores was accounted for in the analysis. To reflect this process, an integrated cyclic analysis is demonstrated capturing the thermal behaviour during fill, solidification and die open stages in the casting cycle.
HuangH.HillJ. L.BerryJ. T.A free thermal contraction method for modelling the heat transfer coefficient at the casting/mould interface. Cast Metals, 1993, 5, 212–216.
2.
LewisR. W.UsmaniA. S.CrossJ. T.Efficient mould filling simulation in castings by an explicit finite element method. Int. J. Numer. Meth. in Fluids, March 1995, 20, 493–506.
3.
McAdieR. L.CrossJ. T.LewisR. W.GethinD. T.A finite element enthalpy technique for solving coupled nonlinear heat conduction/mass diffusion problems with phase change. Int. J. Numer. Meth. for Heat and Fluid Flow, December 1995, 5, 907–921.
4.
ZhangJ. Y.UsmaniA. S.LewisR. W.A realistic coupled thermo-mechanical finite element model of casting systems. In Proceedings of WCCM III, The Third World Conference on Computational Mechanics, Chiba, Japan, August 1994.
5.
SunR. C.Simulation and study of surface conductance for heat flow in the early stage of casting. AFS Cast Metals Res. J., 1970, 6, 105–110.
6.
SullyL. J. D.The thermal interface between castings and chill moulds. AFS Trans., 1976, 84, 735–744.
SvenssonI. L.SchmidtP.Thermal expansion of gases at the metal-mould interface in permanent mould castings. Cast Metals, 1993, 6, 127–130.
9.
IsaacJ.ReddyG. P.SharmaG. K.Variations of heat transfer coefficients during solidification of castings in metallic moulds. Br. Foundryman, 1985, 78, 465–468.
10.
NishidaY.DrosteW.EnglerS.The air gap formation process at the casting-mould interface and the heat transfer mechanism through the gap. Metall. Trans., 1986, 17B, 833–844.
11.
ShahverdiH. R.FarhadiF.KarimitaheriA.DavaniP.AsgariK.A mathematical model for air-gap formation at the metal-mould interface in the computer simulation of the solidification of A1–12%Si in a sand mould. Cast Metals, 1994, 6, 231–236.
12.
BellF.GethinD. T.AndersonJ. T.A foundry based experimental investigation into the effect of die coats in the gravity casting process. Cast Metals, 1995, 8, 51–56.
13.
LewisR. W.RobertsP. M.Finite element simulation of solidification problems. Appl. Scient. Res., 1987, 44, 61–92.
14.
TranD. V.LewisR. W.GethinD. T.Multiadaptive finite element remeshing with specific reference to metal casting. In Proceedings of International Conference on Numerical Methods in Thermal Problems, 16–21 July 1993, pp. 955–970 (Pineridge Press).
15.
LewisR. W.GethinD. T.UsmaniA.CrossJ. T.RansingR.BellF.Technology transfer: Widening the use of finite element software. Proceedings of Conference on Advanced Casting and Solidification Technology, Helsinki, 12–13 September 1994, cost 504, pp. 445–458.
16.
MastersI.CrossJ. T.LewisR. W.Cycling analysis: Building an initial temperature for better results. In Ninth International Conference for Numerical Methods in Thermal Problems, Atlanta, Georgia, 17–21 July 1995, pp. 604–617 (Pineridge Press).
