Micro-injection moulding as a replication method is one of the key technologies for micromanufacture. The understanding of process constraints for a selected production route is essential both at the design stage and during mass production. In this research, an existing finite element analysis system is used to verify the effects of four process parameters: the melt and mould temperatures, injection speed, and part thickness. Special attention is paid to the melt flow sensitivity when filling microchannels, particularly the factors affecting the shear rate, pressure, and temperature. In particular, the simulation model was used to investigate the flow behaviour of two polymer materials, polypropylene and acrylonitrile butadiene styrene, by varying the process parameters. Then, the results of this investigation were compared with those reported in an experimental study. Conclusions are made about the accuracy and sensitivity of the proposed simulation model.
YaoD.KimB.Scaling issues in miniaturisation of injection moulded parts. J. Mfg Sci. Engng2004126733–739.
2.
ShaB.DimovS. S.GriffithsC. A.PackianatherM. S.Micro-injection moulding: Study of factors affecting achievable aspect ratios. J. Advd Mfg Technol.200733147–156.
3.
HansenH. N.TheiladeU. A.Surface microstructure replication in injection moulding. In Proceedings of First International Conference on Multi-Material Micro Manufacture, Karlsruhe, Germany2005, pp. 91–94 (ElsevierOxford).
4.
SuY. C.ShahJ.LinL.Implementation and analysis of polymetric microstructure replication by micro injection moulding. J. Micromechanics Microengng200414415–422.
InnY.WangS.Hydrodynamic slip: Polymer adsorption and desorption at melt/solid interfaces. Phys. Rev. Lett.199676467–470.
7.
LaugaE.BrennerM. P.StoneH. A.Microfluidics: The no slip boundary condition. In Handbook of experimental fluid dynamics (Eds FossJ.TropeaC.YarinA.)2005, pp. 1–27 (Springer-VerlagNew York).
8.
TaylorJ. B.KandlikarS. G.CarranoA. L.Characterisation of the effect of surface roughness and texture on fluid flow: past, present, and future. In Proceedings of Third International Conference on Microchannels and Minichannels (ICMM2005), Toronto, Ontario, Canada, 13-15 June2005, pp. 1–8 (American Society of Mechanical EngineersNew York).
9.
GriffithsC. A.DimovS. S.BrousseauE. B.HoyleR. T.The effects of tool surface quality in micro-injection moulding. J. Mater. Processing Technol.2007189418–427.
GreeneJ. P.Numerical analysis of injection moulding of glass fiber reinforced thermoplastics. Part 1: Injection flow and pressure. J. Polym. Engng Sci.199737590–602.
12.
TheiladeU. R. O.Surface micro topography replication in injection moulding, PhD ThesisDepartment of Manufacturing Engineering and Management, Technical University of Denmark2005.
13.
PoslinskiA. J.Effects of processing conditions and material models on the injection pressure and flow length in thin wall parts. In Specialized molding techniques (Eds HeimH.-P.PotenteH.)2001, pp. 99–105 (William Andrew PublishingNew York).
14.
YoungW.Effect of process parameters on injection compression molding of pickup lens. J. Appl. Math. Modelling200529955–971.
15.
HelleloidG. T.On the computation of viscosity shear rate temperature master curves for polymetric liquids. J. Appl. Math.200111–11.
16.
BillmayerF. W.Textbook of polymer science, 2nd edition1971 (John WileyNew York).
17.
TeramachiS.HasegawaA.AkatsukaM.YamashitaA.Molecular weight distribution and correlation between chemical composition and molecular weight in a high conversion copolymer of styrene-methyl acrylate. Macromolecules1978111206–1210.
18.
TadmorZ.GogosC.Principles of polymer processing1973 (John WileyNew York).
19.
NichettiD.Manas-ZloczowerI.Viscosity model for polydisperse polymer melts. J. Rheology199842951–969.
20.
InnY.WangS.Hydrodynamic slip: Polymer adsorption and desorption at melt/solid interfaces. Phys. Rev. Lett.199676467–470.
21.
HarmandarisV. A.MavantzasV. G.TheodorouD. N.KrogerM.RamirezJ.OttingerH. C.VlassopoulosD.Cross over from the Rouse to the entangled polymer melt regime: Signals from long detailed atomistic molecular dynamics simulations supported by rheological experiments. Macromolecules2003361376–1387.
22.
ShenY. K.ShieY. J.WuW. Y.Extension method and numerical simulation of micro injection moulding. Int. Commun. Heat Mass Transfer200431795–804.
23.
YuanS.HungN. P.NgoiB. K. A.AliM. Y.Development of micro replication process. J. Mater. Mfg Processes200318731–751.
GalantucciL. M.SpinaR.Evaluation of filling conditions of injection moulding by integrating numerical simulations and experimental tests. J. Mater. Processing Technol.20031412066–2075.
26.
GrilletA. M.BogaerdsA. C. B.PetersG. W. M.BaaijensF. P. T.Numerical analysis of flow mark surface defects in injection moulding flow. J. Rheology200246651–669.
27.
Mc FarlandA. W.ColtonJ. S.Production and analysis of injection moulded micro optic components. Polym. Engng Sci.200444564–579.
28.
Del VecchioR. J.Understanding design of experiments: a primer for technologists1997 (Hanser Gardner PublicationsCincinnati, Ohio).
29.
AntonyJ.Multi-response optimization in industrial experiments using Taguchi's quality loss function and principal components analysis. J. Qual. Reliability Engng2000163–8.
30.
MehtaN. M.BarryC. M. F.BibberD.TallyD.Validation of flow simulation for micro moulded parts. In Proceedings of the SPE Annual Technical Conference (ANTEC 2003), Nashville, Tennessee, USA, 4–8 May 2003, pp. 3550–3554 (Society of Plastics Engineers, BrookfieldConnecticut).
