A dynamic wire melting phenomenon is found in rotating arc welding since self-regulation of the arc length is not fully performed. Consequently welding current and electrode extension vary rapidly in high speed rotating arc operation. This paper presents the dynamic simulation of wire melting by using the variable space network method and by modelling the heat flux from the molten end of the wire into the electrode. The simulations are compared with experimental results from other references to show a fairly good agreement. By using simulation analyses, it is clarified how the characteristics of the welding power source affect the sensitivity of the arc sensor.
SugitianiY.KobayashiY.MurayamaM.Development and application of automatic high speed rotation arc welding. Weld. Int., 1991, 7(5), 577–583.
2.
CookG. E.Robotic Arc Welding, 1987, pp. 188–194 (Springer-Verlag).
3.
KimC.-H.NaS.-J.A study on arc sensor using rotating arc in horizontal fillet welding. In The National Meeting of Spring 1997, 1997, pp. 129–132 (Korean Welding Society, Seoul).
4.
LesnewichA.Control of melting rate and metal transfer in gas-shielded metal-arc welding. Weld. J., 1958, 37(8), 343s–353s.
5.
HalmoyE.Wire melting rate, droplet temperature, and effective anode melting potential. In Arc Physics and Weld Pool Behaviour, 1980, pp. 49–54 (Welding Institute, Cambridge).
6.
MaoW.UshioM.Measurement and theoretical investigation of arc sensor sensitivity in dynamic state during gas metal arc welding. Sci. Technol. Weld. Joining, 1997, 2(5), 191–198.
7.
ShepardM. E.CookG. E.A frequency-domain model of self-regulation in gas-metal arc welding. In Third International Conference on Trends in Welding Research, 1992, pp. 899–903 (ASM International).
8.
HalmoyE.Simulation of rotational arc sensing in GMAW. IIW document 212-933-98, 1998.
9.
KimY.-S.McEligotD. M.EagarT. W.Analysis of electrode heat transfer in gas metal arc welding. Weld. J., 1991, 70(1), 20s–31s.
10.
QuinnT. P.MadiganR. B.SeiwertT. A.An electrode extension model for gas metal arc welding. Weld. J., 1994, 73(10), 241s–248s.
11.
ZhuP.RadosM.SimpsonW. W.Theoretical prediction of the start-up phase will improve weld quality. Weld. J., 1997, 76(7), 269s–274s.
12.
WaszinkJ. H.Van Den HeuvelG. J. M.Heat generation and heat flow in the filler metal in GMA welding. Weld. J., 1982, 61(8), 269s–282s.
13.
NemchinskyV. A.Heat transfer in an electrode during arc welding with a consumable electrode. J. Phys. D: Appl. Phys., 1998, 31, 730–736.
14.
WaszinkJ. H.Van Den HeuvelG. J. M.Measurement and calculations of the resistance of the wire extension in arc welding. In Arc Physics and Weld Pool Behaviour, 1980, pp. 227–239 (Welding Institute, Cambridge).
15.
PatankarS. V.Numerical Heat Transfer and Fluid Flow, 1980 (McGraw-Hill, New York).
16.
TouloukianY. S.Thermophysical Properties of High Temperature Solid Materials, Vol. 3, 1967 (Macmillan, New York).
17.
LancasterJ. F.The Physics of Welding, 2nd edition, 1986 (Pergamon, Oxford).
18.
KimY.-S.Metal transfer in gas metal arc welding. PhD thesis, MIT, 1989.
19.
MurrayW. D.LandisF.Numerical and machine solution of transient heat-conduction problems involving melting or freezing. J. Heat Transfer, 1959, 81, 106–112.
20.
NeedhamJ. C.Arc stability in gas-shielded arc welding. Weld. Res. Council Bull., 19 December 1968, 313–316.
21.
KimC.-H.NaS.-J.A study of an arc sensor model for gas metal arc welding with rotating arc. Part 2: Simulation of an arc sensor in mechanically rotating gas metal arc welding. Proc. Instn Mech. Engrs, Part B, Journal of Engineering Manufacture, 2001, 215(B9), 1281–1288.
